Suspension Restoration Parts


Go back to the index page

Yes, WE have it in stock!
 We have all these bushings in stock in the color Black & Red.
 Polyurethane bushing sets include enough bushings to do both sides of the vehicle.

If you wanted it today, you should have order it from us yesterday.

Pontiac Fiero

YEAR
FRONT CONTROL ARM BUSHING SET
REAR CONTROL ARM BUSHING SET
REAR TRAILING ARM LINK BUSHING SET
FRONT SWAY BAR FRAME BUSHINGS
 $13.00 pr.
sm. bracket. design
Please measure the diameter of the sway bar before ordering.
FRONT SWAY BAR ENDLINK SET
$15.00 pair
ENGINE CRADLE MOUNTS
ENGINE TORQUE STRUT BUSHING
TIE ROD END or BALL JOINT BOOTS (PAIR)
$3.00 pair
84-87
7-207
$55.00
7-304
$27.00
N/A
See Energy Suspension Page
9-8117
$16.00
Energy Suspension
part number
7-502
$56.00
7-501
 84-88 (4 cyl.)
 85-86 (6 cyl.)
$19.00
 round style
9-13101
pair
$3.00
88 only
7-207

$55.00
*
7-305
$72.00
See Energy Suspension Page
See Energy Suspension Page
*
7-501 (4 cyl.)
$19.00
 round style
9-13101
pair
$3.00
These polyurethane bushings for the Fiero, are all made by Prothane.
 Prothane does not make graphite-impregnated polyurethane.
 The '88 Fiero uses the same front control arm bushings even though the control arm design was changed.
The 7.207 will fit Chevy Citation

Some of the '88 Fiero G.T. cars use a 1-1/8" diameter front sway bar.
Unfortunately, neither Energy Suspension or Prothane will make a small bracket sway bar frame bushing in the 1-1/8" size.
Because the bushing would have an extremely thin side wall.
The only sway bar frame bushings that willl work on this application is modified small bracket design #9-5129-G (1.00").
YOU will have to place this bushing and bracket in a drill press vise and drill press to drill out the 1.00" hole to 1-1/8".
You must be very careful to center the drill bit to the 1.00" hole in the bushing.  
Because the side walls will be very thin, it is easy to end up with a hole in the side of the bushing.  
I have successfully drilled out a few, and have ruined a few bushings, so be careful.
Use a flat-bladed wood boring bit. NO NOT use a fluted bit that you would normally use to drill metal.
You could also us a large round bastard file to enlarge the hole if you want too.

When ordering a rear sway bar endlink for the '88 Fiero, please measure the length of the sleeve that seperates the grommets,
so we can provide the correct part number.

How to identify which dogbone(Engine torque strut rod) you have.
There are 3 different factory dogbones.
1. One has a continuous "rib" around the outside of it, this one will accept polyurethane bushings(7-501),
because the inside area where the bushings go, are relatively smooth and has a straight bore.
2. The other one has smooth circular outer surface and a rib on the center section.
There is a taper inside the area where the bushings fit. The 7-501 polyurethane bushings will not fit the taper.
We have talked to customers who have successfully modiifed the #7-501 to fit the tapered dogbone.
3. There are at least two different lengths of dogbones.
Here is a link to article about Fiero torque strut/dogbones: http://home.sprynet.com/~theogre/tunnel6/index.htm
Then click on the engine menu and pick torque strut.

If anyone has any more information about the fit of these parts please contact us.
Prothane makes these parts, when we have confronted them with application questions
concerning design changes during a model year, they say there were no changes they know of.
Therefore, there is no reason to make any other style dogbone bushings.

McQuay-Norris brand ball joints & tie rod ends for
Fiero - Are in stock.

YEAR
FRONT UPPER
BALL JOINT
FRONT LOWER
BALL JOINT
FRONT OUTER TIE
ROD END
FRONT INNER
TIE ROD END
REAR LOWER
BALL JOINT
REAR TIE
ROD END
TIE ROD END or
BALL JOINT BOOTS (PAIR)
$3.00 pair

84-87
McQuay-Norris
FA-1021
$29.00
McQuay-Norris
FA-1006
$24.00
McQuay-Norris
ES-2232-R
$39.00
McQuay-Norris
ES-2286-R
$40.00
with 14 mm threaded
rack only
McQuay-Norris
FA-1146
$42.00
McQuay-Norris
ES-2255-R
$31.00
9-13101
pair
$3.00
88
n/a
McQuay-Norris
FA-1467
$42.00
Moog
 ES-3238-RL
$31.00
not available
not required
not required
9-13101
pair
$3.00
YEAR
COMPLETE SUSPENSION KIT
PRICE
84-87
 only
Front & rear control arm bushings, front sway bar frame(please measure the diameter of your front sway bar)
& endlinks, engine cradle mounts,
engine strut torque(dogbone) bushings, poly tie rod end boots, poly ball joint boots,
 Front upper & lower ball joints, front outer tie rod ends,
rear lower ball joints and rear outer tie rod ends.
$455.00
1988
Front & rear control arm bushings, front sway bar frame bushings(state diameter of front sway bar) & endlinks,
engine strut torque(dogbone) bushings, poly tie rod end boots, poly ball joint boots,
front LOWER ball joints, front outer tie rod ends.
This kit does not include upper ball joints, because we can not supply them.


$290.00

SUSPENSION tips & suggestion page

PRODUCT WEIGHT
is now included in the charts above.  
1.2# means that the part number listed weighs 1 pound & 2 ounces.  
This is not the shipping weight, just the weight of the part.  
To estimate your shipping cost, you should round up to the next pound and usually add about a pound for shipping weight.  
When we ship via FED-EX we have to round up to the next pound.
 Fed-ex does not accept ounce weight.  
We will always weigh your order on our electronic scale and charge you for the exact weight, rounded up to the next pound.  
For USPS shipping we also round up to the next pound.

SHIPPING COST TO THE EAST COAST OF THE USA,
AS OF AUGUST 10, 2005,
We are providing you with this information, so that you can estimate your shipping cost before you place your order.
This is the cost of shipping from our warehouse in Modesto, California to any address on the east coast of the USA.
 If your address is in a zone west of the east coast zone, your cost will be less.
If Fed-ex will charge us less to ship to your address, then we will charge you less.
It is NOT our goal to make money off of shipping.
We just charge you what the shipping costs us.
(Prices are subject to change)

PACKAGE WEIGHT
 GROUND
 3 DAY AIR
 2 DAY AIR
 1 DAY AIR
1 POUND (1.0#)
 8.65
 15.31
 17.05
 34.38
2 POUNDS (2.0#)
 9.47
 17.16
 19.41
 38.03
3 POUNDS (3.0#)
 10.10
 18.85
 21.33
 40.84
4 POUNDS (4.0#)
 10.52
 20.99
 23.69
 44.50
5 POUNDS (5.0#)
 10.95
 23.07
 26.39
 47.59
6 POUNDS (6.0#)
 11.23
 25.49
 29.31
 51.25
7 POUNDS (7.0#)
 11.56
 27.63
 31.90
 54.06
8 POUNDS (8.0#)
 12.12
 29.93
 34.60
 56.88
9 POUNDS ( 9.0#)
 12.68
 32.24
 37.41
 60.81
10 POUNDS (10.0#)
 13.30
 34.49
 40.00
 63.91
These prices are for packages with a value under $100.00
For orders over $100.00 please add:
 $1.20 per $100.00 value
 $2.50 per $100.00 value
 		$2.50 per $100.00 value
 		$2.50 per $100.00 value
For international orders we normally ship via the United States Postal Service, Airmail Parcel Post.
Here is a link to the USPS website for their rates: http://ircalc.usps.gov/default.asp?Mode=Intl_Single&CID=12268


Yes, we have these bushings in stock, for immediate shipment.
But, remember, if you wanted it today, you should have ordered it from SUSPENSION yesterday.

California residents please add 7.375% sales tax
We DO NOT have a handling charge.
We do charge for the actual cost of shipping.
We normally ship via FED-EX within the U.S.A.
AK or HI and outside of the states we will attempt to use the U.S. POSTAL SERVICE.
You will pay any of your countries duties.

Do you need to order sway bar frame bushings?
 Be sure to measure the diameter of the sway bar before calling us.  
Don't ask someone on the internet, your sister or your mother.  
Grab a caliper or an adjustable wrench(crecent wrench) or a hand full of open wrenches and measure the diameter.  
The sway bar could have been changed in its' past or the factory might have installed an incorrect size.

(209) 578-5101
Tech questions & orders

1(800)-291-5340 ORDERS ONLY

(209) 578-0562 (FAX)
Hours: 8:00 a.m. to 6:00 p.m (P.S.T.)
Pacific Standard Time, West coast of USA, or 'California Time'.
(East Coast times : 11.00 a.m. to 9:00 p.m.)
Monday - Friday,
sometimes, we are here on saturdays


Order Form
 (Quantity x Part #)

Your Name(as it appears on your credit card):

 Your Telephone Number:

 Your Street Address(credit card billing address):

 Your City:

 Your State/Province:

 Your Country:

 Your Zip/Mailing Code:
Your Shipping Instructions:

Please Indicate Method of Payment:
 We do not ship orders C.O.D.

 Your Credit Card Number:
(This is not a secure form, so if you would rather
leave this blank please call us at (209) 578-5101, with your credit card information.)

 Your Credit Card Expiration Date (mm/yy):

If you see a standard email box, your browser will not submit the form.  
Please give us your order information in the email box.  
We will not double your order.
SUSPENSION RESTORATION PARTS COMPANY
319-B MOTOR CITY COURT
MODESTO, CALIFORNIA 95356
Copyright © 2006 SUSPENSION RESTORATION PARTS CO. All Rights Reserved