16.13102 | Front Ball Joint Dust Boot/Cover Replacement | Honda

  • 16.13102 360image 1
  • 16.13102 Front Ball Joint Dust Boots
  • 16.13102 Front Ball Joint Dust Boots
  • 16.13102 Front Ball Joint Dust Boots
  • 16.13102 Front Ball Joint Dust Boots
  • 16.13102 Front Ball Joint Dust Boots
  • 16.13102 360image large 1

Front Ball Joint Dust Boots

Manufacturer: Energy Suspension
Part Number: 16.13102

Color: (?)
Black
Red

Exclusive for DST Customers: (?)
Free Lifetime Warranty Upgrade
Price: $7.66

check_box In Stock check_box Ships Immediately


  • 2 - 13003 - Upper Ball Joint Dust Boots
  • 2 - 13005 - Lower Ball Joint Dust Boots
Suggested part for 16.13102: 9.13103
9.13103 Tie Rod Dust Boots
If your ball joints boots are worn out, chances are your tie rod boots are just as bad. Replace them both as long as you're under the car!

  • Energy Suspension warrants its products against defects in workmanship and material for 24 months when used on passenger cars and light trucks. Products that have been abused, altered, or incorrectly installed are not covered. Energy Suspension will replace defective products or component parts, if inspection for factory personnel determines the part to be defective. Warranty replacement covers only the product. Labor claims, time loss, or freight charges will not be honored.
Cross Reference from 16.13102 to 81702
Prothane 81702
Polyurethane.
Price: $7.77
Warranty: Lifetime Warranty

FitmentFront Ball Joint Dust Boots 16.13102 fits these vehicles:
Details
Polyurethane Front Ball Joint Dust Boots
Finally, someone has made a replacement ball joint dust boot! No more expenseor cost worries when the boot wears out or is damaged either from installation or from day to day use.

16.13102 | Front Ball Joint Dust Boot/Cover Replacement | Honda

Pin Opening Diameter Base Opening Diameter Height of Boot Piece Number
11.55mm
(0.455 inch)
0.5mm
(1.20 inch)
24mm
(0.945 inch)
13003
13mm
(0.511 inch)
36.35mm
(1.43 inch)
24mm
(0.945 inch)
13005
Here is our complete list of universal dust boots.
Polyurethane Front Ball Joint Dust Boots
  • Repair torn and worn out ball joint boots without having to buy the entire ball joint just to get the boot.
  • Adds both durability and that custom look attention custom show car builders!
  • Lasts longer, seals better and looks great for show vehicles!
  • Resist damage from rocks, sand, water, road salt, and oils better than many other O.E.M. rubber boots.
  • Made of Energy's HYPER FLEX performance polyurethane for added performance and durability.
Footnotes
  • One Set Will Cover the Left and Right Side

Energy Suspension Polyurethane Universal Dust Boots

Importance of Dust Boots

Many of you are finding out that the rubber boot on your ball joint or tie rod has rotted away or has split. These boots are extremely important for the suspension of your vehicle. Fortunately, Energy Suspension makes Universal Dust boots that will fit most vehicles. These dust boots are made of polyurethane and are far more durable than rubber. This will seal your boot to retain the grease in the joint, as well as protecting the joint from dirt, sand, water, and snow.

Energy Suspension Universal Dust Boots
Energy Suspension Universal Dust Boots

How to get your measurements

In order to select the proper boot, you will first need to grab a few measurements. The best way to do this is with a set of digital calipers. You will need to measure the diameter of the base where the boot will sit, the diameter of the shaft (also called the Pin Opening Diameter) and the height of the boot. Once you have gotten to your tie rod end measure these three spots. Be sure to be as exact as possible and to write down your measurements. If you have any trouble getting these measurements, give our customer service team at DST a call.

It is important to note that you do not want to choose a boot that is bigger than your measurements. You want to choose a boot that is just slightly smaller than the measurements you obtained. The elasticity of the polyurethane will allow the hole to stretch and grip the joint tightly. If you choose a boot that is too large there will be a gap which lets in debris.

Now that you have these measurements, you can verify that this is the boot that you need. If you find that your measurements do not match this boot, go to our Universal Dust Boot page to match a part to your measurements.

Choose your design

Energy Suspension offers an alternative to the traditional round bushing. There is an octagon shaped dust boot available as an option. The octagonal boots have the same specifications and perform the exact thing. They just offer a more unique look.

Energy Suspension Universal Dust Boots
Energy Suspension 16.13102

Product Reviews for 16.13102 | Front Ball Joint Dust Boot/Cover Replacement | Honda

5 Star (7)
100%
4 Star (0)
0%
3 Star (0)
0%
2 Star (0)
0%
1 Star (0)
0%
starstarstarstarstar

Energy Suspension 16.13102

5 out of 5 based on 7 user reviews. Write a Review

D
verified_user

starstarstarstarstar" Review 2 Years Later "

These parts worked very well for me, at first I thought they were too small but when I went to install them they fit perfectly and was easy to do.

verified_user Verified Buyer - Donald Trenholm - . Energy Suspension 16.13102 - 5 out of 5
M
verified_user

starstarstarstarstar" These parts was just right "

These parts made my job a lot better, thanks.

verified_user Verified Buyer - Mike Dalton - . Energy Suspension 16.13102 - 5 out of 5
J
verified_user

starstarstarstarstar" excelent "

The part fit perfectly and the quality is as expected.

verified_user Verified Buyer - JOSE LUIS DIAZ - . Energy Suspension 16.13102 - 5 out of 5
E
verified_user

starstarstarstarstar" Great value for the money "

These are the cure for the wimpy stock upper and lower ball joint boots...no more grease leaking all over!!

verified_user Verified Buyer - errol yap - . Energy Suspension 16.13102 - 5 out of 5

compare_arrows Compare with Similar Parts


This Part
16.13102 compare
$7.66
Prothane
Prothane compare
$7.77
($0.11) more expensive

question_answer Customer Questions and Answers


Question:
How do you install the ball joint dust boots? Are they just press on? Do they have the wire like the stock piece? Do you load the boot with grease before you put them on, or the ball joint itself?
Answer:
Place the boot onto the ball joint and install by hand, making sure it is snug. Fit the socket or receiver cup over the ball joint assembly and lightly tap until the boot is even and secure. Grease the ball joint itself after you install the dust boot. ...see more