Suspension Restoration Parts Co. - 4 - Bar bushings,Fabricators page

If you have a polyurethane bushing and you want to replace it,
look for a part number molded into the end of the bushing.
ALL Energy Suspension bushings have 4 numbers (but could be 5 numbers) no letters, molded into the end of the bushing.
We can usually help with Energy Suspension bushings.
We have a data base of Energy Suspension part numbers and dimensions, for all their 2000 series bushings.

Prothane has 5 numbers no letters. We can order these but we usually have to order a minimum of 50.
So that can be a problem.

If the bushing has 2 letters and then 4 numbers,
like MO 2165, it is made by Daystar.
Call Daystar @ 800-595-7659.

O.K. you still can not find the bushing you want,
check out this page(click on the link):
See this page if you require a special size bushing or sleeve.
We can check our Energy Suspension data base and attempt to find a comparable bushing made by them.

UNIVERSAL BODY MOUNTS - See also the Body Mount Bushing Page
For use as isolator mounts on applications such as -
obsolete body mounts, kit car, truck beds, tool boxes and many other similar applications.
(see diagram for specific parameters)
Each part number includes 2 complete mounts per set, 4 washers, 2 sleeves and 4 bushings.

#9-4101
Firm Bushing - 88A Durometer
Off Road parameter, Drag Strip, Road Racers, Extreme Use Vehicles,
Various Applications Which Require Firmer Mounting.
$23.00

9-4102
Soft Bushing - 70A Durometer
Applications which require higher degree of isolation.
Universal Transmission/Motor Mounts, Cab/Body/Bed Mounts, Restorations Daily Drivers, Custom Body, Kit Cars,
Also Isolators for Air Compressors, Tool boxes, Generators, Independent Engines, Etc.
$28.00

We suggest the #2-4101 early Jeep CJ body mounts.
These are simple flat bushings with a hole in them.
1-15/16" O.D. x 9/16"I.D. x 21/32"thick.
Both sides are flat.
14 grommets only per set
$23.00

Energy Suspension suggests these bushings for those who are building aftermarket control arms.
The following recommendations are for using standard off the shelf Energy Suspension parts,
when you are designing aftermarket control arms/track(panhard) rod, for the 82-95 GM F-body.
These recommendations have been made after extensive research and testing.
Track Bar (9.9484)
Energy Suspension bushings part number 2134 is recommended for use in aftermarket track rods.
These bushings should be used with Energy Suspension sleeve part number 15-188.
For the proper fit and performance Energy Suspension recommends the following:

The tubing must be chamfered, all burrs and sharp edges removed and there must not be
any weld or weld splatter located where the bushing contacts the tubing.
For a proper fit the following tubing dimensions are recommended:
- a tube I.D. of 1.732" + .000 - .005(Std. tolerance for D.O. M. tubing.)
- a tube O.D. of 2.00" minimum.
- a tube length of 1.380 + .005 - .005
- This tubing must have a smooth and round I.D.
(D.O.M. tubing or machining the I.D. is recommended.)

These recommendations are for the bushings to fit properly and distribute the loads properly
throughout the bushings, sleeve and tubing.

Control Arms
Energy Suspension bushings part number 2156 is recommended for use in aftermarket control arms. These bushings should be used with Energy Suspension sleeve part number 15-010 (.750" X .500" X 2.425") for standard bolts or 15-241 (.750" X .480" x 2.425" for metric bolts. for the proper fit and performance Energy Suspension recommends the following:

The tubing must be chamfered, all burrs and sharp edges removed and there must not be
any weld or weld splatter located where the bushing contacts the tubing.
For a proper fit the following tubing dimensions are recommended:
- a tube I.D. of 1.750" + .000 - .005(Std. tolerance for D.O. M. tubing.)
- a tube O.D. of 2.250" minimum.
- a tube length of 1.920 + .005 - .005
- This tubing must have a smooth and round I.D.
(D.O.M. tubing or machining the I.D. is recommended.)

These recommendations are for the bushings to fit properly and distribute the loads properly
throughout the bushings, sleeve and tubing.

The following recommendations are for using standard off the shelf Energy Suspension
parts, when you are designing aftermarket control arms for the '79 - '96 Ford Mustang.
These recommendations have been made after extensive research and testing.
Lower control arms
The following recommendations are for a 3 piece bushing.
This design will help eliminate the rear suspension from binding during the suspension travel.

For a proper fit we recommend the following:
- D.O.M. tubing or a machined I.D.(a welded seam in the I.D. will tear up a bushings quickly.)
- A tube O.D. of 2.375" min.
- A tube I.D. of 1.937" +.000 - .010"
- A tube length of 2.220" + .005" - .015
- This tubing must have a smooth and round I.D.
(D.O.M. tubing or machining the I.D. is recommended.)
- The tubing must be chamfered, all burrs and sharp edges removed and there must not be
any weld or weld splatter located where the bushing contacts the tubing.
- The grease fitting hole, if used, must be located .800" + .010 -.010" from the edge of the tube.
The offsetting of the grease fitting is essential for proper grease distribution and bushings longevity.

With the tubing recommended above, the following Energy Suspension bushings and sleeves can be used.
The quantity listed will be enough for one set of lower control arms:

OTHER INTERESTING PRODUCTS

#9-9005
Dampener donuts inserted in coil springs allow for a progressive rate
of compression while preventing spring bottoming. Great for competition
use and for vehicles equipped with winches. Available in all standard colors.
2-1/4" tall. 3- 9/16" dia. 2 per set
SRP Price $28.00

Formula 5 Prelube is a versatile, waterproof, non-melting grease containing Teflon.
Formula 5 Prelube forms a tough, durable, chemical resistant firm of lubricant
that prevents metal-to-metal contact even under sever shock loads.
Only a small amount is required to properly lubricate and prevent corrosion.
8 oz. White container in picture above #9-11104 $12.00
3) 1/2 oz. squeeze tubes #9.11110 $3.00
100) 1/2 oz. squeeze tubes #9.11111 $75.00
Note from SRP: The Formula 5 PreLube offered by Energy Suspension and included in most sets where grease is required,
is actually MARINE BOAT TRAILER GREASE.
This is a high paraffin(wax) based grease that sticks to anything it touches.
We do not like this grease because it contains wax(paraffin).
We prefer to use Permatex or Loctite Anti Seize(never seize) grease.
You can purchase it at most all auto parts stores or hardware stores
This grease has graphite in it, but does not have the wax.
Anti-Seize grease is normally recommended for use on sparkplug threads when installed on aluminum heads,
so the threads will not seize. It is a hi-temp and hi-pressure grease.

Universal Products: UNIVERSAL #3: Motor & Transmission Mounts

Color Code for motor and transmission mounts only, add: G- black, R- red.
Example- #3.1114R = red

Performance Motor Mounts- General Motors Co. Style
Performance HYPER-FLEX™ polyurethane motor mounts give both performance gains and longevity benefits.
These babies will handle any and all torque.
This "Early GM" style mount has a built-in torque-ready safety interlock.
Fits GM V-8s (small and big blocks) and some GM V6s.
To determine the mount required- use the following application charts below first.
If your application is not listed use the diagrams and dimensions shown here.

Short & Wide Type, available in 2 finishes:
#3.1114 has a zinc finish $33.00 each
#3.1115 has a chrome finish $49.00 each

See diagram: Inside Width- 2 5/8" Height Base to Bolt Center- 1 3/4"
Replaces O.E. part numbers: 3990914, 3960768, 6258154
Replaces aftermarket numbers: 2267, 2285, 2142

Tall & Narrow Type, available in 2 finishes:
#3.1117 has a zinc finish $35.00 each

#3.1118 has a chrome finish $52.00 each
See diagram: Inside Width- 2 3/8"
Height Base to Bolt Center- 2 3/16"

Replaces O.E. part numbers: 3962740, 3990918, 3962748
Replaces aftermarket number- 2283

Energy Suspension ® automotive transmission mounts were the first to have a
built-in metal safety interlock design- for added confidence from breakage.
Bushing material made of performance HYPER-FLEX™ polyurethane.

NOTE- To Custom Chassis Fabricators- The dimensions shown above are for reference only.
You should obtain the mounts before final fabricating of your particular chassis area.

Universal Mount-#2.1102 Heavy duty mount for custom installations.
Made from HYPER-FLEX™ formula polyurethane–for extreme durability.
Incorporates our patented metal interlock–for safety. Heavy duty metal construction.

Hole To Hole- 4.406" min. to 4.781" max. (4 13/23" min. To 4 25/32" max.)- using a 3/8" bolt.
Stud Size- 7/16"-14, .915" (15/16")

PRODUCT WEIGHT
is now included in the charts above.
1.2# means that the part number listed weighs 1 pound & 2 tenths of a pound.
We are giving this measurement, because this is how Energy Suspension has chosen to give us the weight of each part number.
1 Pound(lb.or #) = 16 ounces(oz.) divided by 10 = 1.6 oz.
This is not the shipping weight, just the weight of the part.
To estimate your shipping cost, you should round up to the next pound and usually add about a pound for shipping weight.
When we ship via UPS(United Parcel Service) we have to round up to the next pound.
UPS does not accept ounce weight, or increments of tenths.
We will always weigh your order on an electronic scale and charge you for the exact weight, rounded up to the next pound.
For USPS(United States Postal Service) shipping we also round up to the next pound.

ABOUT THE COST OF SHIPPING VIA
UPS (United Parcel Service)
AS OF July, 29, 2010.
We are providing you with this information, so that you can ESTIMATE your shipping cost before you place your order.
The prices in the table below represent the cost of shipping a package from our warehouse in
Modesto, California to a residential address in Maine, the furthest point from CA.
Each Monday UPS updates their software with fuel surcharges that change the rates on a weekly basis. This is why we can only give you an estimate of charges.
UPS will charge extra for some rural addresses.
If your address is in a zone west of the east coast zone(Maine to Florida), say in the Midwest or on the West Coast, your shipping cost will be less.
Of course Alaska & Hawaii are exceptions, call us for the rates.
When UPS charges us less to ship to your address, we will charge you less.
If they charge us more than is on the chart below, we charge you more.
We charge you the exact cost of shipping.
After you have placed your order:
1. We will weigh your order
2. Put the weight and your address into the UPS shipping computer
3. Assign the level of shipping you request, Ground, 1 day, 2 day or 3 day
4. Enter the value if it is over $100.00
5. Charge you exactly what the UPS computer says it will cost to ship your order to you.
It is NOT our goal to make money off of shipping.
The UPS prices below are ESTIMATES.
They do not include rural surcharges that could apply to some addresses.
For Alaska & Hawaii please call us for rates.
YOUR SHIPPING OPTIONS

PACKAGE WEIGHT

United Parcel Service
UPS
GROUND
Modesto, CA. to Maine

UPS
3 DAY AIR
Modesto, CA. to Maine

UPS
2 DAY AIR
Modesto, CA. to Maine

UPS
1 DAY AIR
Modesto, CA. to Maine

ADD:
$12.50 for Saturday delivery.

United States Postal Service
USPS PRIORITY MAIL
DELIVERY TO ANY USA
ADDRESSES ONLY.
(2 - 4 DAYS)
For over seas orders
See the USPS website: http://ircalc.usps.gov/
to calculate the cost to ship your order to your country.

United States Postal Service
USPS FLAT RATE BOX SPECIFICATIONS
AND
INSURANCE INFORMATION

1 POUND
(1.0#)

8.49

14.58

18.98

44.94

$5.00 Small #1
Flat Rate Box.

$5.00

UNITED STATES POSTAL SERVICE (USPS)
Required USPS boxes for flat rate service:
USPS PRIORITY BOXES

New small Flat Rate Box is now available
20 pound weight limit
Box #1 = 8-5/8" x 5-3/8" x 1-5/8"
$5.00

Box #2 = 11-7/8 x 3-3/8 x 13-5/8 inches
70 pound wieght limit.
$11.00
Box #3 = 11 x 8-1/2 x 5-1/2 inches.
70 pound wieght limit.
$11.00
even bigger Flat Rate Box now available
70 pound wieght limit.
Box #4 = 12" x 12" x 5-1/5"
$15.00

There is a limit as to how much we can fit
into USPS flat rate boxes.
Rates above are for USA addresses only.
Domestic Insurance
United Parcel Service(UPS) includes insurance.

USPS does NOT include INSURANCE.
If USPS loses your package and your order is not insured,
you will have to place another order.
We will not offer to pay for the lost part or for another shipment.
If you want to add insurance
to your USPS shipment,
ask us for it.
Here are the USPS insurance rates:
$0.01 TO $50.00 value of your order
$1.75

$50.01 TO $100.00 value of your order
$2.25

$100.01 to $200.00 value of your order.
$2.75

$200.01 to $300.00 value of your order
$4.70

$300.01 to $400.00 value of your order
$5.70

A note about USPS shipments. The USPS carrier usually picks up packages at our business every morning by 10:30 A.M. Monday - Friday (we are not open Saturday or Sunday). This means that your order may not leave until the next day, so figure on 3-4 days for delivery to USA addresses.

UNITED STATES POSTAL SERVICE (USPS)
rates to CANADA
1 Pound = $20.00
2 Pounds = $22.00
3 Pounds = $24.00
4 Pounds = $26.00
5 Pounds = $27.00
New small Flat Rate Box is now available
4 pound limit
Box #1 = 8-5/8" x 5-3/8" x 1-5/8"
$12.00
Box #2 = 11-7/8 x 3-3/8 x 13-5/8 inches
20 pound limit
$27.00
Box #3 = 11 x 8-1/2 x 5-1/2 inches.
20 pound limit
$27.00
bigger Flat Rate Box now available
Box #4 = 12" x 12" x 5-1/5"
20 pound limit
$34.00

Flat rate service is available for
some other countries.
See this website: http://ircalc.usps.gov/
for rates to your country.

Indemnity Limit Not Over	Canada *	All Other Countries
$50	$1.75	$2.50
100	2.25	3.40
200	2.75	4.40
300	4.70	5.40
400	5.70	6.40
500	6.70	7.40
600	7.70	8.40
675	8.70	N/A
700	N/A	9.40
Additional Indemnity *	N/A	1.00

Insurance is not available for all countries. Check with USPS or check with us to determine if Insurance is available to your country.

2 POUNDS
(2.0#)

9.43

16.61

21.95

49.78

$5.00 Small #1
Flat Rate Box.

$9.00

3 POUNDS
(3.0#)

10.70

18.65

24.81

54.18

$5.00 Small #1
Flat Rate Box.

$11.00 Flat rate. Must be able to fit into a USPS flat rate box.

$15.00 Flat rate. Must be able to fit into the a USPS flat rate box.

4 POUNDS
(4.0#)

10.71

20.41

27.83

59.02

$5.00 Small #1
Flat Rate Box.

$11.00 Flat rate. Must be able to fit into a USPS flat rate box.

$15.00 Flat rate. Must be able to fit into the a USPS flat rate box.

5 POUNDS
(5.0#)

11.21

22.17

31.35

63.42

$11.00 Flat rate. Must be able to fit into a USPS flat rate box.

$15.00 Flat rate. Must be able to fit into the a USPS flat rate box.

6 POUNDS
(6.0#)

11.45

24.20

34.05

68.2

$11.00 Flat rate. Must be able to fit into a USPS flat rate box.

$15.00 Flat rate. Must be able to fit into the a USPS flat rate box.

7 POUNDS
(7.0#)

11.78

26.29

37.13

72.66

$11.00 Flat rate. Must be able to fit into a USPS flat rate box.

$15.00 Flat rate. Must be able to fit into the a USPS flat rate box.

8 POUNDS
(8.0#)

12.38

28.49

40.65

77.17

$11.00 Flat rate. Must be able to fit into a USPS flat rate box.

$15.00 Flat rate. Must be able to fit into the a USPS flat rate box.

9 POUNDS
( 9.0#)

13.04

30.36

44.33

81.95

$11.00 Flat rate. Must be able to fit into a USPS flat rate box.

$15.00 Flat rate. Must be able to fit into the a USPS flat rate box.

10 POUNDS (10.0#)

13.76

32.45

47.80

86.68

$11.00 Flat rate. Must be able to fit into a USPS flat rate box.

$15.00 Flat rate. Must be able to fit into the a USPS flat rate box.

UPS INSURANCE
is included for the first $100.00 value
For orders over $100.00 please add:

Add $0.60 for each additional $100.00 value.

INSURANCE IS NOT INCLUDED WITH USPS SHIPMENTS.
YOU MUST REQUEST INSURANCE COVERAGE.

We accept:
Visa, MasterCard, American Express or Discover credit cards.
At this time, we do not accept PayPal.
To process your order we will need:
1. Your NAME as it appears on the credit card.
2. The BILLING address of the credit card.
3. Your PHONE number
4. The CREDIT CARD number
5. The EXPIRATION date of the credit card.
6. The three(3) digit CVV2 security code on the BACK of the credit card. AMEX 4 digits on top right hand corner of the card.
7. How do you want us to ship your order? USPS or UPS?
Yes, you can give us an alternate ship to address.
But we must have the billing address to process your order.

FOR OUR INTERNATIONAL CUSTOMERS
For international orders we normally ship via the United States Postal Service(USPS).
United Parcel Service(UPS)next day air and second day air is also available, upon request.
Every countries Customs authorities require us to declare the parts we sell to you as merchandise.
We are required to send a commercial invoice that lists the value of each part ordered.
We will charge you for the value of the parts plus the cost of shipping to you.
We will not show a reduced price on the invoice or declare the parts as gifts or samples.
You are responsible for all of your countries duties and taxes.
If you want to estimate of the cost of shipping:
1. Add up the total weight of the parts you want to order(the weight is under every part number),
add 1 pound for packaging material.
2. Go to the USPS website http://ircalc.usps.gov/ and enter the country where you want the parts shipped.
3. Enter the weight of your order.
4. Check out the different shipping options, and choose the one that is best for you.

Call us with your order, or we would prefer that you EMAIL your order to sales@suspension.com.
This way we will know the correct spelling of your name and address.

We only stock these bushings in the color black.

Yes, we have all of these bushings in stock, for immediate shipment.
But, remember, if you wanted it today, you should have ordered it from SUSPENSION yesterday.

California residents please add 8.375% sales tax.
We normally ship via U.P.S. within the U.S.A.
U.S.P.S. Priority Mail is available upon request

Suspension Restoration Parts Co.
319-C Motor City Ct.
Modesto, California 95356 USA
East Coast Hours: 11:00 A.M. to 8:00 P.M.(EST) Monday - Friday
West Coast Hours: 8:00 a.m. to 5:00 p.m (PST) Monday - Friday.

(209) 578-5101 Tech questions & order line.
10:00 AM to 5:00 PM(PST), M-F.
(800) 291-5340 Orders Only. 8:00 A.M. - 5:00 P.M.(PST) Monday - Friday.
NO tech questions answered here.
(209) 578-0562 (FAX) Anytime

BUSHING O.D.	SLEEVE I.D.	SLEEVE LENGTH	BARREL LENGTH	FLANGE LENGTH	SET PART NUMBER	SRP SET PRICE	POLY BUSHING ONLY specs.	INNER SLEEVE ONLY specs.
1-1/8"	1/2"	1.400"	1/2"	3/16"	9-9105	$9.00	9001 .744" i.d. x 1.138" o.d. x .665" o.a.l.	15.10.03.39 .500" i.d. x .750" o.d. x 1.400" o.a.l.
1-1/8"	9/16"	1.400"	1/2"	3/16"	9-9106	$9.00	9001 .744" i.d. x 1.138" o.d. x .665" o.a.l.	15.10.42.39 .5625" i.d. x .750" o.d. x 1.400" o.a.l.
1-1/4" (1.252")	1/2"	1.750"	0.614"	7/32"	9-9107	$9.00	9002 .744" i.d. x 1.252" o.d. x .846" o.a.l.	15.10.04.39 .500" i.d. x .750" o.d. x 1.750" o.a.l.
1-1/4" (1.252")	9/16"	1.750"	0.614"	7/32"	9-9108	$9.00	9002 .744" i.d. x 1.252" o.d. x .846" o.a.l.	15.10.05.39 .5625" i.d. x .750" o.d. x 1.750" o.a.l.
1-1/4" (1.252")	5/8"	1.750"	0.614"	7/32"	special order	$13.00	9002 .744" i.d. x 1.252" o.d. x .846" o.a.l.	15.10.192.39 .625" i.d. x .750" o.d. x 1.750" o.a.l.
1-1/8"	5/8"	1.750"	3/4"	1/8"	9-9111	$9.00	9072 0.813" i.d.x 1.145" o.d. x 0.856" o.a.l.	15.10.199.39 .625" i.d. x .813"o.d. x 1.750" o.a.l.

Part #	Outside Dimension of the bushing barrel or sleeve	Inside Dimension	Barrel Length	Flange Thickness	Flange Outside Dimension	Overall Length	Price Each	Suggested Companion Part Number	What is it?
2121	0.875"	0.500"	0.900"	0.125"	1.00"	1.025"	$1.50	Not available	special Hot rod spring eye bushing
2122	0.750"	0.500"	1.00"	0.125"	1.00"	1.125"	$1.75	Not Available	special Hot rod spring eye bushing
2404	0.748"	0.498"	0.675"	0.140"	1.00"	0.807"	$1.75	Not Available	leaf spring bushing
2180	0.997"	0.501"	1.200"	0.340"	1.302"	1.528"	$2.50	Not Available	leaf spring bushing
7028	1.066"	0.742"	0.640"	0.217"	1.507"	0.853"	$3.36	15.10.04.39 15.10.05.39 15.10.192.39 sleeve	control arm bushing
2054	1.624"	0.865"	1.482"	0.236"	2.496"	1.718"	$2.91	15.10.48.39	leaf spring bushing
15.10.48.39	0.875"	0.625"				3.500"	$4.50	2054	sleeve
2134	1.758"	0.875"	0.600"	0.250"	2.178"	0.850"	$3.25	15.10.188.39	leaf spring bushing
15.10.188.39	0.875"	0.562"	*	*	*	1.875"	$3.25	2134	sleeve
2156	1.765"	0.750"	0.830"	0.295"	2.180"	1.125"	$3.10	15.10.354.39	leaf spring bushing
15.10.354.39	0.750"	0.500"	*	*	*	2.250"	$3.25	2156	sleeve
15-10.241.39	0.750"	0.480"	*	*	*	2.453"	$3.90		sleeve
15-10.10.39	0.750"	0.500"	*	*	*	2.425"	$3.90		sleeve
2239	1.963"	0.747"	*	*	*	0.566"	$6.51	15.10.171.39	leaf spring bushing
2238	1.974"	0.747"	0.803"	.331"	2.391"	1.123"	$4.00	15.10.171.39	leaf spring bushing
15-10.171.39	0.750"	0.480"	*	*	*	2.87"	$3.50	2238 & 2239	sleeve
3029	*	*	*	*	*	*	$7.00	15.10.170.39	15.12.98.01 complete assembly
3098	*	*	*	*	*	*	$2.80	3029	thrust washer
15.10.170.39	0.750"	0.480"	*	*	*	2.40"	$3.70	3029	sleeve
2009	1.375"	0.750"	1.170"	.325"	1.775"	1.500"	$3.50	15.10.08.39 (9/16" i.d.) or 15.10.45.39 (1/2" i.d.)	leaf spring bushing
2130	1.519"	0.751"	0.712"	0.212"	1.979"	0.918"	$2.75	use with 1.500" I.D. d.o.m tubing	consider using with the 2004 or 2123 for unique lengths.
2123	1.510"	0.750"	0.963"	0.211"	1.982"	1.165"	$3.64	15.10.170.39	consider using with the 2004 or 2130 for unique lengths.
2004	1.515"	0.750"	1.220"	.250"	1.975"	1.470"	$2.99	15.10.08.39 (9/16" i.d.) or 15.10.45.39 (1/2" i.d.)	leaf spring bushing w/ flutes on I.D. consider using with the 2130 or 2123 for unique lengths.
2002	1.524"	0.749"	0.967"	0.510"	1.970"	1.470"	$3.61		leaf spring bushing w/ flutes on I.D.
2006	1.517"	0.745"	1.475"	0.213"	1.900"	1.677"	$6.54		Leaf spring bushing w/ smooth bore I.D.
2076	1.750"	0.750"	1.245"	0.255"	2.200"	1.500"	$2.99	15.10.08.39 (9/16" i.d.) or 15.10.45.39 (1/2" i.d.)	leaf spring bushing
2223	1.520"	0.733" Flutes inside	1.246"	0.268"	1.963"	1.490"	$3.85	15.10.08.39 (9/16" i.d.) or 15.10.45.39 (1/2" i.d.)	used on aftermarket springs for Jeeps
15.10.08.39	0.750"	0.565	*	*	*	3.00"	$3.00	use w/2) 2009 or 2004 or 2076	sleeve
15.10.45.39	0.750"	0.500	*	*	*	3.00"	$3.00	use w/2) 2009 or 2004 or 2076	sleeve
15.10.346.39	0.750"	0.625"	*	*	*	3.50"	$3.75	use with 2006, 2007, 2008	sleeve
2008	1.104"	0.625"	1.461"	0.256"	1.496"	1.727"	$2.50	15.10.28.39	leaf spring bushing
15.10.28.39	0.625"	0.438"	*	*	*	3.500"	$1.75	use with 2008	sleeve
15.10.159.39	0.750"	0.500"	*	*	*	3.500"	$3.75	use with 2006, 2007, 2008	sleeve
15.10.09.39	0.750"	0.563"	*	*	*	3.500"	$3.75	use with 2006, 2007, 2008	sleeve
15.10.01.39	0.750"	0.500"	*	*	*	3.700"	$3.25		sleeve
15.10.123.39	1.00"	0.750"	*	*	*	3.335"	$4.15		sleeve
2170	1.125"	0.750"	0.974"	0.198"	1.373"	1.167"	$2.99	Use with sleeve #15.10.516.39 (0.750" X 0.500" X 2.350")	Leaf spring bushing w/ smooth bore I.D.
9001	1.138"	0.744"				0.665"	$1.70	15.10.03.39 or 15.10.42.39	4 bar bushing
15.10.03.39	0.750"	0.500"	*	*	*	1.400"	$1.75	9001	sleeve
15.10.42.39	0.750"	0.5625"	*	*	*	1.400"	$1.75	9001	sleeve
9002	1.252"	0.744"				0.846"	$1.75	15.10.04.39 or 15.10.05.39	4 bar bushing
15.10.04.39	0.750	0.500"	*	*	*	1.750"	$1.75	#9002	sleeve
15.10.05.39	0.750"	0.5625"	*	*	*	1.750"	$2.25	#9002	sleeve
15.10.192.39	0.750"	0.625"	*	*	*	1.750"	$2.50	#9002 & 5/8" bolt.	sleeve
9072	1.145"	0.813"	0.730"	.0140"	1.398"	0.856"	$1.80	15.10.199.39	4 bar bushing
15.10.199.39	0.813"	0.625"	*	8	*	1.750"	$2.75	#9072	sleeve
7013	1.791"	0.623"	0.769"	0.290"	2.059"	1.053"	$ ?	15.10.52.39	3.7103 Pont. Fiero torque strut bushing
15.10.52.39	0.625"	0.438"	*	*	*	2.100"	$ ?	7013	sleeve
Part #	Outside Dimension of the bushing barrel or sleeve	Inside Dimension	Barrel Length	Flange Thickness	Flange Outside Dimension	Overall Length	Price Each	Suggested Companion Part Number	What is it?

Quantity	Part Number	Description	Price
4	2239	Center position	$6.51 ea.
8	2238	Outside position	$4.00 ea.
4	15.10.171.39	Pivot sleeve	$3.50 ea.

Quantity	Part Number	Description	Price	Found in set #
2	3029	axle end(mounts in axle)	$7.00 ea.	B4-3129G ($20.00)
2	3098	thrust washer axle end	$2.80 ea.	B4-3129G ($20.00)
4	15.10.170.39	pivot sleeve	$3.70 ea.	B4-3129G ($20.00)
4	2123	frame end	$3.64 ea.	9.9483G ($14.00)