BODY MOUNT BUSHINGS
If you have reached this page, it is because you are desperate.
No one makes body mounts bushings for your vehicle.
This is a
Do It Yourself
web page.
This is not going to be easy,
In fact it is going to be damn hard to figure out what bushings will fit your vehicle,
but now you will at least have the size of the body mount bushings that Energy Suspension makes,
so maybe you can figure out which one of their bushings might fit your vehicle.
All of these bushings are
SPECIAL ORDER
BODY MOUNT BUSHINGS
Body mounts are usually made of 70-A durometer Hyper-Flex polyurethane material.
70-A durometer Hyper-Flex polyurethane material that are black or red, do not contain graphite.
To assure accurate measurements, we measured each bushing with a digital caliper.
The measurement of the bushings you receive may vary slightly due to the differences in the mold used to make the bushing.
There could also be slight differences in the height of the bushing, as these are cut by several individuals, very rapidly.
It is possible for you to modify any polyurethane bushing.
Use a Lathe, mill, drill press, belt sander, or whittle it with your pen knife.
When you have figured out what bushings will fit your vehicle, call us at 800-291-5340 to place your order.
Please do not call us and ask which one of these bushings will fit your vehicle.
| last Update: August 6, 2007. The information listed here is actually still a work in progress. We are still compiling data for this page. We hope to add the pictures later. 148 part numbers listed so far. It took us more than two months to compile this information. PRICE OF BUSHINGS: We have provided you with the last price that we had from Energy Suspension if we have purchased this bushing in the past. This should be considered a PRICE ESTIMATE, not your final price. Energy Suspension could increase the price(and we expect that they will). Some of the prices we have are several years old. If there is a '?' where the price should be, this means we have never ordered this part and do not know what Energy Suspension will charge us for the part. |
||||||||
| PART NUMBER THAT IS MOLDED INTO THE BUSHING |
A OUTSIDE DIAMETER |
B OUTSIDE DIAMETER OF STEP. THIS IS THE PART THAT WOULD FIT INTO ANOTHER BUSHING OR A HOLE IN THE FRAME OF THE CAR. |
C INSIDE DIAMETER OF HOLE IN BUSHING |
D THICKNESS. THIS WILL GIVE YOU THE THICKNESS OF THE BUSHING BETWEEN THE FRAME AND THE BODY. |
E OVERALL THICKNESS INCLUDING THE STEP. (SEE B) |
ESTIMATED PRICE See note above. Expect price to be more than is listed here. |
THE INSTRUCTIONS IN THE BODY MOUNT SET SAID TO PAIR THIS BUSHING(OR BUSHINGS) WITH THE ONE YOU ARE INTERESTED IN. |
THE BODY MOUNT SET WE FOUND THE BUSHING IN. |
| 4001 bottom #1 post. |
2.470" |
1.385" |
1.065" |
0.550" |
0.905" |
$4.15 |
4002 15.02.29.39(1.282" O.A.L. shell) |
3.4101 & 3.4142 |
| 4002 top #1 post. |
1.855" |
1.368" I.D of recessed hole. depth of hole is 0.200" |
1.035" |
0.355" |
0.555" |
$3.32 |
4001 |
3.4101 & 3.4142 |
| 4003 top #3 post. |
2.180" |
1.515" |
1.170" |
0.655" |
1.015" |
$4.15 |
4004 |
3.4101, 3.4103 & 3.4142 |
| 4004 bottom #2 & 3 post. |
2.167" |
1.500" I.D of recessed hole. depth of hole 0.245" |
1.160" |
0.385" |
0.630" |
$4.15 |
4005, 4003 15.02.30.39 (1.495" O.A.L. shell) 15.03.14.39 (0.500" i.d. x 2.500" o.d. flat washer) |
3.4101, 3.4142, 3.4144 |
| 4005 top #2 post. |
2.485" |
1.520" |
1.180" |
0.795" |
1.150" |
$4.90 |
4004 15.02.31.39 ( 1.410" O.A.L. shell) 15.03.24.39 .(625" i.d. x 2.500" o.d. flat washer) |
3.4101 & 3.4142 |
| 4006 Graphite impregnated 95-A durometer |
1.933" |
1.088" |
0.660" |
0.435" |
0.568" |
$? |
4007Use with sleeve #15.10.99.39 0.688" o.d. x 0.500" i.d. x 0.937" L |
3.4102, 3.4152 |
| 4007 Graphite impregnated 95-A durometer |
1.587" |
N/A |
0.653" |
0.498" |
N/A |
$1.66 |
4006 |
3.4102, 3.4152 |
| 4008B |
2.897" |
1.392" |
0.960" |
2.637" |
2.845" |
$? |
3.4107 |
|
| 4008 |
2.905" |
1.400" |
0.965" |
2.605" |
2.820" |
$14.89 |
3.4103 |
|
| 4009 |
2.340" |
1.630" |
0.930" |
tapered O.D. or Cone-shaped |
1.265" |
$4.15 |
4031, 4062 use with 0.878" O.D. x 0.565" I.D. x 1.2.150" L |
3.4137 |
| 4010 |
2.880" |
1.395" |
0.880" |
1.115" |
1.310" |
$5.01 |
4026, 4030 use with .875" O.D. x 0.750" I.D. x 2.00" L sleeve |
3.4103, 3.4149 |
| 4011 |
2.330" |
1.500 |
0.835" |
tapered O.D. or Cone-shaped |
1.265" |
$4.15 |
Does not normally use either an inner sleeve or flat washers. |
3.4140, 3.4160 |
| 4012 |
1.975" |
0.815" |
0.560" |
0.833" |
1.024" |
$3.32 |
||
| 4013 |
2.387" |
0.945" |
0.615" |
0.890" |
1.080" |
$? | 4014 use with sleeve 0.630" O.D. x 0.500" I.D. x 1.653" long Flat washer: 2.5" O.D. x 0.375" I.D x 0.120" th. |
8.4101 |
| 4014 |
1.640" |
- |
0.615" |
- |
0.860" |
$? | 4013 |
8.4101 |
| 4015 |
1.793" |
0.960" |
0.615" |
0.760" |
0.935" |
$? | 4014 |
8.4101 |
| 4016 |
$? | |||||||
| 4017 |
2.016" |
1.055" |
0.680" |
0.560" |
0.730" |
$2.91 |
||
| 4019 Simple flat puck style |
1.954" |
- |
0.680" |
- |
0.385" |
$2.49 |
||
| 4021 Simple flat puck style |
1.960" |
n/a |
0.875" |
n/a |
0.470" |
$1.95 |
2.00" OD. x 0.437" ID. x 0.120" TH #15.03.09.39 round flat washer. | 3.4155, 3.4160 |
| 4025 |
2.340" |
1.387" |
0.882" |
0.780" |
0.960" |
$3.74 |
4026, 4028, 4056 use sleeve # 15.10.59.39 (7/8" x 3/4" x 1.50") 15.03.14.39 (2.5" OD x 0.500" ID x 0.120"TH) round flat washer. or 15.03.28.39 ( 2.5" OD x 0.750" ID x 0.120" TH) round flat washer. |
3.4104, 3.4107, 3.4110, 3.4138, 3.4149, 6.4101, 3.4160 |
| 4026 |
2.270" |
1.300" I.D recessed step |
0.935" |
0.610" |
0.760" |
$3.74 |
4010, 4059, 4025 |
3.4138, 3.4149 |
| 4027 |
2.230" |
1.390" |
1.030" |
0.752" |
0.960" |
$? |
4028 (c) |
4.4102 |
| 4028 |
2.00" Tapered O.D. |
1.800" |
0.890" I.D of recessed hole on backside 1.395" Depth 0.100" |
0.589" |
0.700" |
$? |
4027 use sleeve # 15.10.59.39 (7/8" x 3/4" x 1.50"). 4025 use sleeve #15.10.91.39 (0.875" x 0.750" x 1.375"). 15.03.09.39 (2.0" OD x 0.437" ID x 0.120"TH) round flat washer. |
3.4149, 3.4160 |
| 4029 |
3.025" |
1.760" |
1.035" |
1.310" |
1.520" |
$? |
4030 |
4.4102 |
| 4030 |
2.680" |
1.390" I.D of recessed hole
on backside. 0.130" depth of recessed hole, on backside. |
0.900" |
0.730" |
0.860" |
$4.57 |
4010, 4031, 4071 |
3.4149 |
| 4031 |
3.030" |
1.387" |
1.027" |
1.182" |
1.390" |
$7.89 |
4009, 4030 |
4.4102 |
| 4032 |
2.455" |
1.315" |
0.865" |
1.144" |
1.520" |
$? |
4033 |
4.4103 |
| 4033 |
2.415" |
1.310" I.D of recessed hole
on backside. 0.236" depth of recessed hole, on backside. |
0.610" |
0.571" |
0.807" |
$? |
4032 |
4.4103 |
| 4034 |
2.908" |
1.380" |
1.055" |
1.207" |
1.590" |
$6.23 |
4035 |
4.4103 |
| 4035 |
2.660" |
1.370" I.D of recessed hole
on backside. 0.266" depth of recessed hole, on backside. |
0.925" |
0.676" |
0.942" | $? |
4034 |
4.4103 |
| 4036 |
2.465" |
1.380" |
1.047" |
2.334" |
2.723" |
$? |
4037 |
4.4103 |
| 4037 Simple flat puck style |
2.262" |
n/a |
0.918" |
n/a |
0.952" |
$3.24 |
4036 |
4.4103 |
| 4038 |
2.270" |
1.251" |
0.873" |
0.524" |
0.698" |
$? |
4039 7/8" x 11/16" x 1.060" sleeve 0.875" O.D. x 0.750"I.D. x 1.060" L sleeve |
3.4120 |
| 4039 Simple flat puck style |
1.892" |
n/a |
0.875" |
n/a |
0.575" |
$? |
4057, 4038 2.00" OD. x 0.437" ID. x 0.120" TH #15.03.09.39 round flat washer. |
3.4120 |
| 4040 |
2.255" |
1.481" |
0.498 |
1.006" |
1.315" |
$? |
||
| 4041 |
2.071" |
1.475" |
0.997" |
0.793" |
0.939 |
$3.24 |
4044 |
3.4113 |
| 4042 |
2.010" |
1.480" |
0.745" |
0.889" |
1.045" |
$3.49 |
4045 |
3.4113 |
| 4044 Simple flat puck style |
2.015" |
n/a |
0.997" |
n/a |
0.588" |
$2.49 |
4041 |
3.4113 |
| 4045 Simple flat puck style |
2.002" |
n/a |
0.743" |
n/a |
0.575" |
$2.66 |
4042 |
3.4113 |
| 4048 Simple flat puck style |
1-15/16" |
n/a |
9/16" |
n/a |
21/32" |
$1.50 |
Does not normally use either an inner sleeve or flat washers. | 2.4101 14 of #4048 in set. |
| 4049 |
1.953" |
1.374" |
0.742" |
0.603" |
0.716" |
$2.91 |
4050 |
3.4111, 3.4112, 3.4127, 3.4128 |
| 4050 Simple flat puck style |
1.774" |
n/a |
0.746" |
n/a |
0.711" |
$2.91 |
4052 |
3.4111, 3.4112, 3.4127, 3.4128 These sets do not have any hardware. |
| 4052 |
2.011" |
1.246" |
0.745" |
0.461" |
0.599" |
$? |
||
| 4053 |
2.925" |
1.407" |
0.910" |
0.940" |
1.085" |
$? |
4055 |
3.4110 |
| 4054 |
2.925" |
1.397" |
0.910" |
0.504" |
0.665" |
$? |
4056 |
3.4110 |
| 4056 |
$6.47 |
|||||||
| 4057 |
1.725" W x 2.455" L rectangle |
1.255" |
0.870" |
0.475" |
0.680" |
$? |
4039, 4021 2.00" OD. x 0.437" ID. x 0.120" TH #15.03.09.39 round flat washer. 2.500"L x 1.750"W x 0.125"TH rec. flat washer #15.03.104.39. |
3.4120, 3.4160 |
| 4059 |
2.892" |
1.376" |
0.860" |
0.947" |
1.146" |
$5.81 |
3.4103, 3.4107 |
|
| 4060 |
2.000" |
1.320" I.D of recessed hole
on backside. 0.280" depth of recessed hole, on backside. |
0.575" | 0.390" |
0.670" |
$? |
4065 |
4.4107 |
| 4061 |
2.945" |
1.780" |
1.070" |
1.255" |
1.438" |
$? |
4062 |
4.4107 |
| 4062 |
2.600" |
n/a |
0.913" |
n/a |
0.945" |
$? |
4009 |
3.4137 |
| 4063 |
2.925" |
1.712" |
1.025" |
2.505" |
2.900" |
$? |
4064 |
4.4107 |
| 4064 |
2.580" |
1.705" I.D of recessed hole
on backside. 0.453" depth of recessed hole, on backside. |
0.910" |
0.531" |
0.984" |
$? |
4063 |
4.4107 |
| 4065 |
2.455" |
1.318" |
0.600" |
0.680" |
1.006" |
$? |
4060 |
|
| 4067 |
3.019" |
1.880" |
1.315" x0.838" Rectangle hole |
1.122" |
1.745" |
$5.81 |
4068 |
|
| 4068 Simple flat puck style |
2.859" |
n/a |
1.858" |
n/a |
1.261" |
$5.40 |
||
| 4069 |
2.445" |
1.007" |
0.754" |
1.130" |
1.522" |
$6.56 |
4070 |
4.4109 |
| 4070 |
2.400" |
0.998" I.D of recessed hole
on backside. 0.272" depth of recessed hole, on backside. |
0.623" |
0.528" |
0.800" |
$? |
4069 |
4.4109 |
| 4071 |
2.922" |
1.776" |
1.072" |
1.010" |
1.210" |
$? |
4030 |
4.4109 |
| 4072 |
2.00" |
1.134" |
0.875" |
0.625" |
0.759" |
$2.08 |
7019, 4073 use with sleeve 7/8" x 3/4" x 1.375" Long |
3.4126, 3.4138 |
| 4073 Simple flat puck style |
1.785" |
n/a |
0.875" |
n/a |
0.715" |
$1.99 |
||
| $? |
||||||||
| $? |
||||||||
| 4076 |
3.030" |
1.880" |
1.085" |
1.608" |
2.278" |
$? |
4078 |
3.4148 |
| 4077 |
3.030" |
1.880" |
1.085" |
2.050" |
2.735" |
$? |
4079 |
|
| 4078 |
2.845" |
N/A |
1.860" |
N/A |
1.136" |
$? |
4076, 4117 |
3.4148, 5.4106 |
| 4079 |
3.030" |
2.346" I.D recessed step 1.820" I.D of recessed hole. 0.500" depth of recessed hole, on backside. |
1.918" |
0.750" |
1.130" |
$? |
4076, 4077 |
3.4148 |
| 4084 |
2.195" |
1.383" |
1.020' |
0.807" |
1.120" |
$? |
4090 (c) 1.00" O.D. x 0.750" I.D. x 1.500" L sleeve |
3.4129 |
| 4085 |
2.500" |
1.500" |
0.915" |
1.256" |
1.655" |
$7.06 |
4068, 4078 |
3.4131, 5.4106 |
| 4088 |
2.530" |
1.508" |
1.025" |
0.878" |
1.236' |
$? |
4091 1.00" O.D. x 0.750" I.D. x 1.500" L sleeve |
3.4129 |
| 4089 |
2.530" |
1.510" |
1.028" |
0.624" |
0.979" |
$? |
4091 & 1.00" O.D. x 0.750" I.D. x 1.250" L sleeve 4090 & 1.00" O.D. x 0.750" I.D. x 1.375"" L sleeve |
3.4129 |
| 4090 |
2.224" |
1.500' recessed hole on backside |
1.000" |
0.491" |
0.754" |
$2.49 |
4084 (c) |
3.4129 |
| 4091 |
2.525" |
1.500" I.D. 0.208" deep recess on backside. |
1.000" |
0.528" From bottom of recess to top of bushing |
0.754" |
$4.40 |
3.4129 |
|
| 4092 |
2.325" |
1.360" |
0.865" |
0.765" |
0.925" |
$3.49 |
3.4104 |
|
| 4093 |
2.390" |
1.150" |
0.695" |
0.940" |
1.061" |
$? |
4096 use w/2.5" dia. washer |
5.4101 |
| 4094 |
2.390" |
1.145" |
0.700" |
1.380" |
1.512" |
$? |
4096 use w/2.5" dia. washer |
5.4101 |
| 4095 Simple flat puck style |
1.940" |
n/a |
0.670" |
n/a |
0.495" |
$2.41 |
4095 use with 1.20" long sleeve. 2.00" O.D. flat washer |
5.4101 |
| 4096 |
2.417" |
1.975" Chamfered taper side |
0.685" |
n/a |
1.555" |
$? |
4094 |
5.4101 |
| $? |
||||||||
| 4098 Simple flat puck style |
1.625" x 2.415" rectangle |
n/a |
0.488" |
n/a |
0.500" |
$? |
4099 |
|
| 4099 Simple flat puck style |
1.520" x 4023" rectangle |
n/a |
2 x 0.495" 2.52" c to c |
n/a |
0.275" |
$? |
4098 |
|
| 4100 Simple flat puck style |
1.095" |
n/a |
2 x 0.495" 2.52" c to c |
n/a |
0.278" |
$? |
||
| 4102 |
2.328" |
1.508" |
0.865" |
1.038" |
1.266" |
$? |
4103 |
3.4136 |
| 4103 |
2.211" |
1.500" I.D of recessed hole on backside. 0.195" depth of recessed hole. |
0.930" |
0.450" |
0.645" |
$? |
4102 |
3.4136 |
| 4109 |
1.670" |
1.195" |
0.750" |
0.240" |
0.935" |
$? |
4110 (c) 0.750" O.D x 0.625" I.D x 1.00" L sleeve |
3.4138 |
| 4110 |
1.960" |
1.390"I.D of recessed hole. 0.500" depth of hole |
0.750" |
0.200" |
0.700" |
$? |
4109 (c) |
3.4138 |
| 4111 |
2.355" |
1.370" |
0.65" |
0.900" |
1.100" |
$5.64 |
3.4138 |
|
| 4112 |
2.921" |
1.263" |
0.900" |
0.950" |
1.115" |
$? |
4062 use with 0.878" O.D. x 0.565" I.D. x 1.865" L Sleeve |
3.4137 |
| 4113 |
2.200" |
1.500" |
0.880" |
0.840" |
1.150" |
$2.91 |
4114 |
3.4136, 3.4145 |
| 4114 |
2.200" |
1.500" I.D of recessed hole on backside. 0.2.45" depth of recessed hole. |
0.940" |
0.530" |
0.780" |
$2.08 |
4113 |
3.4136, 3.4145 |
| 4115 |
2.190" |
1.508" |
0.885" |
0.840" |
1.150" |
$3.98 |
4116 (c) |
3.4136, 3.4145 |
| 4116 |
1.824" |
1.560" I.D of recessed hole on backside. 0.170" depth of recessed hole. |
0.820" |
0.906" |
1.076" |
$? |
4115 (c) |
3.4136, 3.4145 |
| 4117 |
2.925" |
1.890" |
0.900" |
1.092" |
1.732" |
$? |
4078 |
5.4106 |
| 4122 |
Dimensions of flange: 2.550" x 2.040" Oval. |
1.990" x 1.488" oval |
1.625" x 1.138" oval |
1.320" |
1.660" |
$1.25 |
||
| 4123 |
2.470" |
1.318" |
0.870" |
0.910" |
1.310" |
$? |
4033 |
4.4105 |
| 4124 |
2.900" |
1.380" |
||||||