BUMP STOPS
Go
back to the index page
Yes, WE have
it in stock!
If you wanted it today,
you should have order it from us yesterday.
ALL BUMP STOPS FEATURE:
Specially designed
mechanical interlock
3/8" x 16 course
thread stud, unless discription says otherwise.
Nylon locking nut
Bumpstops are always packaged in pairs.
9.9101 All purpose bump stop for control arms, traction bars and leaf springs, designed to be easily trimmed for custom fits. A must for tuning traction bars. 2-1/8" Tall, 2" Dia. 2 per set. $11.00 .7# |
9.9102 Low profile button head bump stop for use where area is limited due to suspension height change, such as control arms on mini trucks. 11/16" Tall, 2" Dia. 2 per set. $9.00 .5# |
9.9103 Smaller general purpose bullet shaped bump stop, ideal for control arms. 1-9/16" Tall, 1-1/2" Dia. 2 per set. $9.00 .5# |
|
|
RACE STYLE 
9.9104* Designed with a large reinforced metal plate welded to mounting plate and molded in. 4-1/2" Tall, 4-1/2" Length, 2-1/2" Wide. 2 per set. $60.00 *Special formula to absorb energy on impact One of these can be used as a pinion snubber on some Mopar B-body cars. 4.3# |
9.9109* Low profile competition style bump stop. 2-1/2" Tall, 4-1/2" Length, 2-1/2" Wide. 2 per set. $37.00 *Special formula to absorb energy on impact 3.2# |
9.9116 Button head bump stop 1" Tall, 2" dia.. (similar 9-9121, only larger) 2 per set. $9.00 .5# |
|
9.9117 Flat head bump stop. 1" Tall, 2-15/16" Dia $16.00 .9# |
9.9118 Low profile rectangular bump stop. 7/8" Tall. 1-7/8" Length x 1-3/8" Wide. 2 per set. $9.00 .5# |
9.9119 Rectangular bump stop. 1-3/8" Tall. 2-3/8 Length, 2" Wide. 2 per set. Same as Mopar lower control arm bump stop 5-6101, can also be used on G.M cars. $9.00 .6# |
|
9.9120 Rectangular pyramid bump stop. 2-11/16" Tall, 2-1/4" Length, 2" Wide. 2 per set. $13.00 1.0# |
9.9121 Low profile button head bump stop. 11/16" Tall, 1-5/8" dia. 2 per set. $9.00 .4# |
9.9132 Ultra low profile bump stop. Similar in design as the 9-9102, only as thin as possible. Use on lowered cars & trucks where clear- is a major problem. 3/8" Tall, 2" Dia. 2 per set. $9.00 .4# |
|
|
(6074.02) red only, it appears as though E.S. is going to discontinue this part number. Button head bump stop, with metric stud (10 mm) 1" tall x 2" dia. $9.00 .5# |
Stepped style bump stop. 2-1/2" tall x 2-7/16" dia. Designed to accept 3/8" dia. socket head bolt. Hardware not included. Easily timmed for custom fitting 2 per set $21.00 1.0# |
Square tapered style bump stop. 2" tall x 2" square. 7/8" long stud 2 per set $11.00 1.0# |
|
|
2 bolt style, fits 1976-86 Jeep CJ-5-7 front and rear position. 1-7/8" tall x 5" overall length x 1-3/4" wide. Designed to accept 3/8" dia. bolts with center to center of 4-1/2" max to 4.00" min. Hardware not included 2 per set. $21.00 1.2# |
Round head bump stop 1-7/8" tall x 2-1/4" dia. Designed to accept 1/2" dia. socket head bolt. Hardware not included. 2 per set. $17.00 .9# |
Stepped style bump stop 3-1/8" tall x 2-7/16" dia. Designed to accept 3/8" dia. socket head bolt. Hardware not included. Easily trimmed for custom fitting 2 per set. $26.00 1.3#
|
9.9145 GM rear bump stop 2 per set $11.00 Same as 3.9103 #6130 .5# |
|
Flat head pad 3/4" tall x 2-3/4" dia. Designed to accept 5/16" dia. socket head bolt. Hardware not included 2 per set. Not to be used as a control arm or axle bump stop. $10.00 .6# |
Button head pad 3/4" tall x 2" dia. Designed to accept 3/8" socket head bolt. Hard ware not included. 2 per set. Not to be used as a control arm or axle bump stop. $7.00 .3# |
G.M Style bump stop. Fits many 1970-99 cars & trucks. 1-3/4" tall x 2-1/4" long x 1-1/16" wide 1" long stud with a 5/16" dia. locating pin at 1.00" offset 2 per set $14.00 .8# |
|
|
Round pull thru bump stop. Fits many G.M. vehicles 1970-99. Also fits 9/16" hole(1/8" thick) 1-9/16" tall x 1-13/16" dia. 2 per set. $9.00 .7 |
Single hump early GM style. Lower control arm direct replacement for: '64-'72 Chevelle, '68-'72 Nova and '67-'69 Camaro. .7# |
9.9155
2000-01 Ford Excursion 4 wd front & rear axle bump stop set- pair 3-1/8" tall $23.00 1.4# |
|
|
9.9156 2000-01 Ford Excursion 4 wd rear axle overload snubber set - pair 2-1/2" tall $27.00 1.2# |
picture n/a 9.9158 .4#
|
picture n/a 9.9165 GM style pull thru bump stop. fits many GM models. 3" tall x 2-7/16" long x 2-3/8" wide. 2 per set. $19.00 1.3# |
picture n/a 9.9166 .6#
|
|
Jeep front bump stop set. Fits 1997-99 Jeep Wrangler. Must reuse all metal parts 2 per set. $26.00 1.0# |
3.9101 G.M Style pull thru bump stop. Fits many 1978-88 RWD cars and trucks 2-5/8" tall x 1-13/16" long x 1-15/16"wide 2 per set $17.00 .8# |
3.9102 same
as 9.9139
Fits many 1978-99 G.M. RWD cars and trucks. 1-1/4" tall x 1-1/2" long x 1-9/16" wide 2 per set $8.00 .4# |
3.9103 G.M style pull thru bump stop. Fits many 1978-88 G.M RWD cars and trucks. 1-5/8" tall x 1-13/16" long x 1-15/16" wide $11.00 .6# |
|
Jeep front bump stop set fits 1997-03 Jeep Wrangler TJ. Must re-use ALL metal parts. 2 per set. $26.00 1.0# |
Fits many Ford cars 1979-99. Front position with 7/8" shaft dia.. 1-7/16" tall, 2-3/16" X 7/8" ID. 2 per set. $10.00 .5# |
Fits most 1970-78 Nissan cars with 3/4" shaft diameter. 1-3/4" tall, 2" OD X 3/4" ID. 2 per set. $9.00 .4# |
|
9.6109 Fits many McPherson strut style and standard shock absorbers with 11/16" dia. shaft. 1-9/16" tall, 1-1/2" OD X 11/16" ID 2 per set. $10.00 .3# |
9.6110 Fits many McPherson strut style and standard shock absorbers with 5/8" dia. shaft. 1-2/16" tall, 1-1/2" OD X 5/8" ID 2 per set. $5.00 .3# |
9.6111 Fits many McPherson strut style and standard shock absorbers with 1/2" dia. shaft. 1-1/4" tall, 1-3/8" OD X 1/2" ID 2 per set. $4.00 .2# |
|
picture n/a Fits many McPherson strut style & standard shock absorbers with 12 mm dia. shaft. 1-9/16" tall, 2.00" o.d. X 12 mm i.d. 2 per set $9.00 .6# |
picture n/a Fits many McPherson strut style & standard shock absorbers with 12 mm dia. shaft. 2.00" tall 1-3/4" o.d. X 12 mm i.d. 2 per set. $8.00 .4# |
