• 13026 Universal Dust Boots 13026

Universal Dust Boots 13026

Manufacturer: Energy Suspension
Part Number: 13026
Rating 168 Reviews


Made in Black Only: (Learn More)
Exclusive for DST Customers: (Learn More)
Free Lifetime Warranty Upgrade
Price: $6.60

In Stock Ships Immediately

Volume Pricing

Qty: 1-99

Qty: 100-499

Qty: 500+


Universal Dust Boots | 21.25mm pin ID x 51mm base id

Pin Opening Diameter Base Opening Diameter Height of Boot Piece Number
21.25mm (0.83 inches) 51.00mm (2.00 inches) 40.30mm (1.58 inches) 13026
  • 1 - 13026 - Dust Boot
  • Energy Suspension warrants its products against defects in workmanship and material for 24 months when used on passenger cars and light trucks. Products that have been abused, altered, or incorrectly installed are not covered. Energy Suspension will replace defective products or component parts, if inspection for factory personnel determines the part to be defective. Warranty replacement covers only the product. Labor claims, time loss, or freight charges will not be honored.

Energy Suspension Polyurethane Universal Dust Boots

Importance of Dust Boots

Many of you are finding out that the rubber boot on your ball joint or tie rod has rotted away or has split. These boots are extremely important for the suspension of your vehicle. Fortunately, Energy Suspension makes Universal Dust boots that will fit most vehicles. These dust boots are made of polyurethane and are far more durable than rubber. This will seal your boot to retain the grease in the joint, as well as protecting the joint from dirt, sand, water and snow.

Energy Suspension Universal Dust Boots

Energy Suspension Universal Dust Boots

How to get your measurements

In order to select the proper boot, you will first need to grab a few measurements. The best way to do this is with a set of digital calipers. You will need to measure the diameter of the base where the boot will sit, the diameter of the shaft (also called the Pin Opening Diameter) and the height of the boot. Once you have gotten to your tie rod end measure these three spots. Be sure to be as exact as possible and to write down your measurements. If you have any trouble getting these measurements, give our customer service team at DST a call.

It is important to note that you do not want to choose a boot that is bigger than your measurements. You want to choose a boot that is just slightly smaller than the measurements you obtained. The elasticity of the polyurethane will allow the hole to stretch and grip the joint tightly. If you choose a boot that is too large there will be a gap which lets in debris.

Now that you have these measurements, you can verify that this is the boot that you need. If you find that your measurements do not match this boot, go to our Universal Dust Boot page to match a part to your measurements.

Choose your design

Energy Suspension offers an alternative to the traditional round bushing. There is an octagon shaped dust boot available as on option. The octagonal boots have the same specifications and perform the exact thing. They just offer a more unique look.

Energy Suspension Universal Dust Boots
Energy Suspension 13026

Product Reviews for Ball Joint Dust Boots 13026

Energy Suspension 13026

5 out of 5 based on 168 user reviews. Write a Review

Very good.
5 out of 5 - Review 1 Year Later
Roland Brukx - . Energy Suspension 13026
The review is not based on the product itself but the poor customer service I received. Not to mention it took over three weeks for me to receive my order. Plus I only received 1 not the two that I ordered.Editors Note: At the time of the order the kit he ordered was on back order. He was notified of the issue. He was given the option of keeping the order and wait 7-14 days or cancel. He chose to wait. DST does notify you when we have back order issues.
1 out of 5 - Review 1 Year Later
Peter Ferber - . Energy Suspension 13026

Product Reviews for Energy Suspension Ball Joint Dust Boots

Fit as they should, urethane should last better than rubber.
5 out of 5 - look to be good quality
Gerald Sheppard - . Energy Suspension 5.13102
These parts worked very well for me, at first I thought they were too small but when I went to install them they fit perfectly and was easy to do.
5 out of 5 - Review 2 Years Later
Donald Trenholm - . Energy Suspension 16.13102
These boots are very high quality, my factory boots were thin sheet rubber and ripped apart over time. These replacements will last the lifetime of the car.
5 out of 5 - Highest quality
jeffrey daley - . Energy Suspension 9.13127
Love em as I had the rubber dust covers which were ripping within the first few months leaking grease as well as letting road grime in at the same time. These have held up well with no visual signs of cracks or distortion.
5 out of 5 - Review 1 Year Later
WALTER FURIAN - . Energy Suspension 5.13102
These are quality ball joint boots. Super simple to install and a much more durable product than the OEM boots. Im very satisfied with the purchase process and the product.
5 out of 5 - Review 1 Year Later
Michael Pruden - . Energy Suspension 9.13130
Great fit great service.
5 out of 5 - well made part better than om boots
Adrian colin Martin - . Energy Suspension 9.13130
One year later and the dust boots are going strong with no signs of deterioration.
5 out of 5 - Review 1 Year Later
Glenn wright - . Energy Suspension 5.13102
Fit my 1970 Chevelle like a glove!
5 out of 5 - Good quality
Timothy Killworth - . Energy Suspension 9.13125
Very good.
5 out of 5 - Review 1 Year Later
Roland Brukx - . Energy Suspension 13025
OK on a collector car. Never drive much.
5 out of 5 - Review 2 Years Later
James K Bottoms - . Energy Suspension 9.13125