Complete Strut Assemblies
A strut, coil spring and top mount already assembled, so no spring compressor is needed.
This interactive diagram shows the front suspension, steering, axles and rear suspension of the 2018 Acura ILX. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit your car, down to the side.
We carry parts for it Not stocked yet Hover or tap any part.
The 2018 ILX uses MacPherson struts up front. Each strut's clevis foot bolts to the top of the knuckle with two bolts, and an L shaped lower arm with a bolt on ball joint holds the bottom. The steering rack sits behind the front axle. The rear is a multi-link design: a wide lower arm carries the coil spring, a straight link sits ahead of it, an arched upper arm sits on top, and the knuckle's own long forward leg runs to a bushing on the body. The rear shock stands apart from the spring.
We carry replacement parts for 22 of the 33 components on this diagram, 60 parts in all. See every part for the 2018 Acura ILX.
A strut, coil spring and top mount already assembled, so no spring compressor is needed.
An L shaped pressed steel arm under each front corner. Its long front leg pivots on an eye bushing under the subframe, its short rear leg holds a large upright bushing, and the ball joint bolts to the pad at its outer end.
Signs of wear: Clunks over bumps, a loose or wandering feel, torn bushings or uneven tire wear.
Tip: Left and right arms are different parts. The 2016 to 2022 ILX arm is not the same as the 2013 to 2015 arm, so check the years before you order.
The large upright bushing pressed into the round boss at the end of the arm's short rear leg. A vertical bolt holds it to the subframe. It lets the arm swing and soaks up road shock.
Signs of wear: A clunk when braking or over bumps, steering that wanders under braking, or cracked rubber you can see from under the car.
Tip: Suppliers list this bushing as the forward bushing; on this car it is the large vertical one in the arm's round boss. It must be pressed out and in, so many owners fit a complete arm instead.
See all Front Control Arm Bushings parts for the 2018 Acura ILX
A ball joint bolted by its three hole flange to the pad at the outer end of the lower arm. Its stud rises into the bottom of the knuckle.
Signs of wear: Clunks over bumps, play when the wheel is rocked top to bottom, or uneven tire wear.
Tip: It bolts to the arm, so it can be changed without replacing the arm.
The upright that carries the wheel bearing and hub. Its top ear sits in the strut's clevis on two bolts, the ball joint holds its bottom, and its rear arm takes the outer tie rod.
Signs of wear: Rarely a wear item. Check it after a hard curb strike.
Tip: The knuckle on the diagram is a simplified shape.
A MacPherson strut. Its clevis foot bolts to the top of the knuckle with two bolts, and its top goes through the coil spring to the top mount under the cowl. The sway bar link bolts to a tab on its body.
Signs of wear: Bouncing after bumps, nose dive on braking, fluid on the strut body, or cupped tires.
Tip: Complete strut assemblies with the spring and mount fitted save using a spring compressor. Plan an alignment afterwards.
The coil spring sits on a seat on the strut body and pushes up against the top mount.
Signs of wear: A front end that sits low on one side, or a clunk from a broken coil end.
Tip: Replace springs in pairs. Lowering springs change the ride height, so plan an alignment.
The rubber mount and bearing at the top of the strut. Three studs hold it to the strut tower under the cowl cover, and the strut turns on it when you steer.
Signs of wear: A knock or creak from the top of the tower when turning or over bumps.
Tip: Replace the mounts when you replace the struts, because the strut has to come apart anyway.
The two 16 mm bolts that hold the strut's clevis to the top of the knuckle. An offset cam bolt in place of the upper one lets the camber be set.
Signs of wear: Uneven wear on the inside or outside edge of the front tires, or camber out of range after a curb strike or on a lowered car.
Tip: Fit the cam bolt in the upper hole, then align the car.
See all Front End Alignment Kit parts for the 2018 Acura ILX
A 20 mm tubular bar across the back of the front subframe, held in two rubber bushings. Its ends come forward to the links on the struts and keep the car flatter in turns.
Signs of wear: Rarely a wear item. Noise usually comes from its bushings or links.
Tip: A thicker aftermarket bar reduces roll further. Bushings must match the bar diameter.
A short rod with a ball stud at each end, from the end of the sway bar up to a tab on the strut body.
Signs of wear: A rattle or clunk over small bumps, usually from a worn ball stud.
Tip: Replace the links in pairs.
See all Front Sway Bar Endlinks parts for the 2018 Acura ILX
The bent outer end of the tie rod. Its ball stud fits up into the steering arm at the back of the knuckle.
Signs of wear: Loose or wandering steering, a clunk when turning, or wear on the inner or outer tire edges.
Tip: Count the turns when you remove it, so the toe stays close until the alignment.
See all Front Outer Tie Rod End parts for the 2018 Acura ILX
The straight inner rod, with a ball socket that threads onto the end of the steering rack under the rack boot.
Signs of wear: Play in the steering, a knock over bumps, or a wandering feel.
Tip: Turbo and non turbo cars can use different inner rods. Check the fit notes.
See all Front Inner Tie Rod End parts for the 2018 Acura ILX
The rubber bellows that seals each end of the steering rack over the inner tie rod.
Signs of wear: A torn boot lets dirt and water into the inner tie rod and the rack.
Tip: Replace a torn boot quickly, before the inner joint wears.
The electric power steering rack, across the car behind the front axle above the subframe. It moves the tie rods to steer the front wheels.
Signs of wear: Heavy or uneven steering effort, or a knock from the rack.
The half shafts drive the front wheels. The passenger shaft runs behind the engine on an intermediate shaft with a carrier bearing.
Signs of wear: Clicking on tight turns, a vibration when accelerating, or grease thrown from a torn boot.
Tip: Boot kits, axle nuts and the carrier bearing are listed here.
An arched arm at the top of each rear knuckle. Its inner end pivots in a bracket on the body. It sets the rear camber.
Signs of wear: Uneven inner tire wear at the rear, or a knock over bumps from a worn bushing.
Tip: Adjustable arms are sold for lowered cars that need the rear camber brought back. Align the car after fitting.
A straight link ahead of the spring arm, from the subframe to the knuckle. It helps hold the rear toe.
Signs of wear: Clunks over bumps, or a rear end that feels loose in corners.
The wide lower arm from the subframe to the bottom of the knuckle. The coil spring sits in its pocket.
Signs of wear: Clunks over bumps, worn bushings or rear tires wearing on one edge.
Tip: Left and right arms are different parts.
The bracket and bolt that hold the inner end of the rear upper arm to the body. A camber kit swaps them for a slotted bracket and an offset bolt, so the rear camber can be set.
Signs of wear: Rear tires wearing on the inside edge, often on a lowered car.
Tip: Fit one per side, then align the car.
An offset bolt with cam washers, greased, that lets the rear toe be set at the inner end of a lower link.
Signs of wear: Rear tires that wear on the edges, or a rear toe setting that will not hold.
Tip: Adjust both sides, then align the car.
The rear upright that carries the hub and brake. Every rear link bolts to it, and its long forward leg runs to a bushing on the body, so it also does the job of a trailing arm.
Signs of wear: Rarely a wear item.
Tip: The knuckle on the diagram is a simplified shape.
The rear shock stands apart from the spring, from an eye low on the knuckle up through the wheel house to a nut under the trunk trim.
Signs of wear: Bouncing after bumps, a rear that floats at speed, or fluid on the shock body.
Tip: Replace shocks in pairs.
The rear coil spring sits between the pocket of the spring arm and a seat in the body, with a rubber isolator at each end.
Signs of wear: A rear that sits low on one side, or a clunk from a broken coil.
Tip: Replace springs in pairs.
A 15 mm bar across the rear subframe, held in two rubber bushings, with its ends out to short links on the knuckles.
Signs of wear: Rarely a wear item. Noise usually comes from the links or bushings.
Tip: Some aftermarket bars fit front wheel drive models only. Check the fit notes.
A short link with a ball stud at each end, from the end of the rear sway bar out to a boss on the knuckle's forward leg.
Signs of wear: A rattle from the rear over small bumps.
Tip: Replace the links in pairs.
A sealed bearing pressed into the knuckle. The hub with the wheel studs is pressed through it.
Signs of wear: A hum or growl that rises with speed and changes when the car turns.
Tip: Pressing the bearing in and out needs a press or a bearing tool.
See all Front Wheel Bearing Assembly parts for the 2018 Acura ILX
A sealed hub and bearing unit that bolts to the rear knuckle with four bolts and carries the five wheel studs.
Signs of wear: A hum or growl from the rear that rises with speed.
Tip: The unit bolts on, so no press is needed.
See all Rear Wheel Bearing and Hub Assembly parts for the 2018 Acura ILX
The vented front brake disc, 282 mm across.
Signs of wear: Pulsing in the pedal, grooves, or a lip at the outer edge.
Tip: Replace rotors in pairs, with new pads.
The floating caliper on its bracket, ahead of the front axle.
Signs of wear: A pull to one side when braking, a sticking brake, or a fluid leak.
Tip: Bleed the brakes after fitting a caliper.
The pads, shown lifted out of the caliper.
Signs of wear: Squealing, grinding, or a long pedal.
The solid rear brake disc.
Signs of wear: Grooves, rust ridges or a pulsing pedal.
Tip: Replace rotors in pairs, with new pads.
The rear caliper, behind and above the rear axle. The electronic parking brake works through it.
Signs of wear: A dragging rear brake or a parking brake fault light.
Tip: Cars with the electric parking brake need a scan tool to retract the piston.
The rear pads, shown lifted out of the caliper.
Signs of wear: Squealing or grinding from the rear.
Sway bar links, the large rear bushing of the front lower control arm, struts and strut mounts are the usual ones. A clunk over small bumps is most often a link.
No. The front is a strut design, so each front corner has only a lower control arm and a lower ball joint. The rear has an upper arm on each side.
No. From 2016 the ILX uses a different front lower arm, ball joint and larger front brakes, so parts for the 2013 to 2015 car do not fit. Check the years in the fit notes.
Yes, after tie rods, control arms, struts or rear arms. Front camber cam bolts and rear camber and toe kits are available when you need more adjustment, for example on a lowered car.
The 2016, 2017 and 2018 ILX share this drawing. The 2019 to 2022 cars use different front brake pads and are checked separately.
Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.