Front End Steering Rebuild Kits
Package kits bundle the wearing front end parts for this truck in one order.
This interactive diagram shows the front suspension, steering, driveline and rear suspension of the 2016 Ford F-150 4x4. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit your truck, down to the side and position.
We carry parts for it Not stocked yet Hover or tap any part.
The 2016 F-150 4x4 uses independent front suspension. A wide forged lower arm and an upper arm hold each knuckle, and a coilover strut stands on the lower arm ahead of the CV axle. The CV axles bolt to a differential carried on the frame. Steering is a rack and pinion with electric assist, mounted ahead of the differential, and the sway bar runs behind the lower arms. At the rear, a solid axle sits on leaf springs just outboard of the frame rails, with the shocks leaning forward from the axle ends.
We carry replacement parts for 30 of the 38 components on this diagram, 127 parts in all. See every part for the 2016 Ford F-150 4WD.
Package kits bundle the wearing front end parts for this truck in one order.
Front and rear shock sets for the whole truck.
A strut, coil spring and top mount already assembled, so no spring compressor is needed.
Kits that raise the front to level the truck, or lower it.
The upper ball joint is pressed into the forged steel upper arm. Its stud points down into the top of the tall steering knuckle.
Signs of wear: Clunking over bumps, wandering steering, uneven tire wear, or play when the wheel is rocked top to bottom.
Tip: The factory upper joint comes with the arm. Separate press-in joints fit replacement arms only, so check which arm is on the truck.
See all Front Upper Ball Joint parts for the 2016 Ford F-150 4WD
The lower ball joint is pressed into the outer end of the lower arm and held with a snap ring. Its stud points up into the bottom of the knuckle.
Signs of wear: Clunking over bumps, wandering steering, uneven tire wear, or play when the wheel is rocked top to bottom.
Tip: The SVT Raptor uses a different lower joint; the parts listed here fit the other trims.
See all Front Lower Ball Joint parts for the 2016 Ford F-150 4WD
A curved forged arm that arches over the coilover. Its two bushings bolt to the strut tower bracket ahead of and behind the coilover top, and the ball joint sits at its outer end.
Signs of wear: Clunks, a torn ball joint boot, or cracked bushings.
A wide A-arm with a long front leg. Its front and rear bushings bolt into brackets under the frame, the coilover's lower eye bolts into a clevis on top of the arm, and the ball joint is at the outer end.
Signs of wear: Clunks on bumps or braking, shimmy, or bushings that are cracked or pushed out of their eyes.
Rubber bushings in the two eyes of the upper arm.
Signs of wear: Squeaks, clunks, or cracked rubber at the arm's inner end.
See all Front Control Arm Bushings parts for the 2016 Ford F-150 4WD
Rubber bushings in the front and rear eyes of the lower arm.
Signs of wear: Clunks over bumps, a pull under braking, or torn rubber.
See all Front Control Arm Bushings parts for the 2016 Ford F-150 4WD
The lower arm pivot bolts carry the cams that set caster and camber.
Signs of wear: The truck will not hold an alignment, or a cam bolt is seized.
Tip: After a lift or leveling kit, a cam kit with more range can bring the alignment back.
See all Front End Alignment Kit parts for the 2016 Ford F-150 4WD
The front strut carries the coil spring, its seats and a bumper. An eye at its bottom bolts fore and aft into a clevis on the lower arm, ahead of the CV shaft, and the top plate's three studs go up through the strut tower.
Signs of wear: Bouncing after bumps, nose dive under braking, or oil on the shock body.
See all Front Shock Absorber parts for the 2016 Ford F-150 4WD
The coil spring sits on the shock between its lower seat and the top mount.
Signs of wear: A front end that sits low or leans, or a broken coil.
Tip: Replacing the spring needs a spring compressor, or a complete coilover assembly.
See all Front Coil Springs parts for the 2016 Ford F-150 4WD
The top plate of the coilover, with three studs into the strut tower and a rubber insulator.
Signs of wear: A clunk at the top of the front corner or a torn insulator.
The front sway bar runs across behind the lower arms' rear crossmember, held under the frame in two bushings. Its ends reach forward and up to links above the lower arms.
Signs of wear: Body lean in turns.
The bar's two 34 mm bushings, in clamps under the frame.
Signs of wear: Clunks or squeaks over bumps.
See all Front Sway Bar Bushings parts for the 2016 Ford F-150 4WD
A long bolt through two ball socket housings, from the end of the sway bar down to the rear leg of the lower arm.
Signs of wear: A rattle or clunk over small bumps.
Tip: The SVT Raptor uses a different link.
See all Front Sway Bar Endlinks parts for the 2016 Ford F-150 4WD
The outer end of the tie rod. Its stud goes into the knuckle's steering arm, ahead of the axle.
Signs of wear: Loose steering, toe wear on the tires, or a torn boot.
Tip: Count the turns when unscrewing it, so the alignment stays close until it can be set.
See all Front Outer Tie Rod End parts for the 2016 Ford F-150 4WD
The inner tie rod screws into the end of the rack inside the boot.
Signs of wear: Play in the steering, or a knock when turning the wheel by hand.
Tip: Trucks with the 6.2L V8 keep hydraulic power steering; check the engine when ordering.
See all Front Inner Tie Rod End parts for the 2016 Ford F-150 4WD
A rack and pinion ahead of the front differential, with an electric assist unit on the passenger end and a rubber boot over each inner tie rod. Trucks with the 6.2L V8 use a hydraulic rack.
Signs of wear: Fluid leaks, a torn boot, or free play in the wheel.
Each CV axle plugs into the differential on a splined stub and drives the hub. The driver and passenger axles are different parts.
Signs of wear: Clicking in turns, a torn boot, or grease thrown around the wheel.
See all CV Joint Parts - Front parts for the 2016 Ford F-150 4WD
The U-joint at the front differential end of the front driveshaft.
Signs of wear: Clunks when shifting into four wheel drive, or a vibration in four wheel drive.
The U-joint where the front driveshaft leaves the transfer case.
Signs of wear: A squeak or clunk in four wheel drive.
The U-joint at the front end of the rear driveshaft, behind the transfer case.
Signs of wear: A clunk taking off, or a vibration that grows with speed.
The U-joint behind the center support bearing, where the two halves of the rear driveshaft meet.
Not on every vehicle: Trucks with a two piece rear driveshaft, such as the long wheelbase SuperCab and SuperCrew.
Signs of wear: A vibration at highway speed or a clunk on take off.
A rubber cushioned bearing on a crossmember that carries the middle of the two piece rear driveshaft.
Not on every vehicle: Trucks with a two piece rear driveshaft.
Signs of wear: A rumble or vibration at speed, or torn rubber.
The U-joint at the rear axle pinion.
Signs of wear: A chirp at low speed, or a clunk on take off.
The leaf springs run just outboard of the frame rails, under the axle. The front eye bolts into a hanger and the rear eye hangs from a shackle.
Signs of wear: Sagging, a broken leaf, or the truck sitting low on one side.
The rubber bushing in the spring's front eye.
Signs of wear: Clunks at the rear on take off and braking.
See all Rear Leaf Spring Bushings parts for the 2016 Ford F-150 4WD
The shackle links the spring's rear eye to a bracket on the frame so the spring can change length as it flexes. Its bushing sits in the bracket.
Signs of wear: A clunk at the rear or a squeak over bumps.
Two U-bolts on each side go over the axle tube and down past the spring to a plate under it.
Signs of wear: A shifted axle or a clunk on take off.
The rear shocks run from the axle up and forward to brackets on the frame, outboard of the springs, with an eye at each end.
Signs of wear: Bouncing, bottoming out, or oil on the shock body.
See all Rear Shock Absorber parts for the 2016 Ford F-150 4WD
A rubber bumper under the frame rail over the axle.
Signs of wear: A harsh bang over big bumps.
A sealed hub and bearing bolted to the knuckle with four bolts, with the ABS sensor wire built in. The CV axle's splined end runs through it.
Signs of wear: A hum that changes in turns, play in the wheel, or an ABS light.
Tip: Six stud and seven stud (heavy duty payload) hubs both exist.
See all Front Wheel Bearing and Hub Assembly parts for the 2016 Ford F-150 4WD
A 350 mm vented rotor over the hub studs.
Signs of wear: Pulsing in the pedal or a scored face.
Tip: Order the six or seven lug rotor to match the wheels.
A twin piston sliding caliper on a bracket bolted to the knuckle behind the axle.
Signs of wear: A pull to one side, a stuck caliper, or a fluid leak.
See all Front Brake Caliper parts for the 2016 Ford F-150 4WD
Two pads inside the caliper, one either side of the rotor.
Signs of wear: Squealing, grinding, or a long pedal.
A 348 mm rotor whose hat is also the parking brake drum.
Signs of wear: Pulsing in the pedal, or a parking brake that won't hold.
A single piston sliding caliper on the axle flange.
Signs of wear: A pull under braking or a seized slide.
See all Rear Brake Caliper parts for the 2016 Ford F-150 4WD
Two pads in each rear caliper.
Signs of wear: Squealing or grinding from the rear.
Tip: Trucks with the electric parking brake use a different rear pad and rotor than trucks with the manual parking brake; the parts listed for your year show which fit.
Two small shoes inside the rear rotor hat, used only by the parking brake.
Signs of wear: The parking brake will not hold the truck.
See all Parking Brake Shoes parts for the 2016 Ford F-150 4WD
Rubber cushions between the frame brackets and the cab and bed.
Signs of wear: Clunks from the body, or a cab that moves on the frame.
Lower ball joints, upper control arms, inner and outer tie rod ends and sway bar links are the usual ones. Check them with the wheels off the ground, because a worn joint shows up as play you can feel by hand.
The factory upper ball joint comes with the upper control arm, so most repairs replace the whole arm. A separate upper joint is listed too, for arms that accept a press-in joint.
All 2016 F-150 4x4 trucks have electric power steering, with the assist unit on the rack, so the rack and inner tie rod parts shown here fit every engine.
No. The Raptor has its own control arms, upper ball joints, sway bar links, hubs and tie rods, so this diagram's parts are for the other 4x4 trims.
Yes. Trucks with the manual parking brake use a drum in the rear rotor hat with parking shoes, and trucks with the electric parking brake use a different rear rotor, pad and caliper. The parts listed for your year and trim show which fit.
Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.