Complete Front Strut Assemblies
A strut with its spring, mount and boot already assembled, so no spring compressor is needed.
This interactive diagram shows the front suspension, steering, driveline and rear suspension of the 2011 Honda CR-V 2WD (front wheel drive). Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit your SUV, down to the side and position.
We carry parts for it Not stocked yet Hover or tap any part.
The third generation CR-V uses MacPherson struts at the front, with the coil spring on the strut and a stamped steel A shaped lower arm under each corner. The steering rack sits low on the rear of the front cradle, behind the axle, and the front brake caliper sits behind the axle. The rear is a multi-link design on its own cross frame: a bent tube trailing arm carries the coil-over strut, a flat stamped lower arm and a short adjustable upper arm locate the knuckle, and a toe link sets the rear toe. The diagram also shows the all wheel drive parts, a rear differential, a prop shaft and two rear CV shafts, marked as optional; your front wheel drive car does not have them.
We carry replacement parts for 31 of the 40 components on this diagram, 104 parts in all. See every part for the 2011 Honda CR-V 2WD.
A strut with its spring, mount and boot already assembled, so no spring compressor is needed.
A rear strut with its spring already assembled, so no spring compressor is needed.
Front and rear struts for the whole car in one order.
Package kits bundle the wearing front end parts in one order, usually for less than buying them one by one.
The strut is the shock absorber and the upper locating part of the front corner in one. Its bottom clamps to the top of the knuckle with two bolts, the coil spring sits on its seat, and its top bolts into the strut tower.
Signs of wear: Bouncing after bumps, nose dive under braking, fluid on the body, or a knock from the top of the strut over rough roads.
Tip: Struts are sold bare or as a complete assembly with the spring and mount already fitted. The complete assembly needs no spring compressor.
See all Front Shock Absorber parts for the 2011 Honda CR-V 2WD
The front coil spring rides on the strut between the lower seat on the strut body and the upper seat under the mount. It holds the front of the car at its ride height.
Signs of wear: A front corner sitting lower than the other, a clunk over bumps from a broken end coil, or tires rubbing on full lock.
Tip: Springs are replaced in pairs. A spring compressor is needed unless you fit a complete strut assembly.
The strut mount bolts the top of the strut to the body. It holds a bearing so the strut and spring can turn with the steering, and rubber to keep road noise out of the car.
Signs of wear: A clunk or creak from the top of the strut when turning, or steering that springs back unevenly.
Tip: Mounts are often replaced with the struts, since the strut has to come out anyway.
A rubber bellows covers the strut rod above the spring seat and keeps dirt off its seal. A bump stop inside it cushions the strut at full compression.
Signs of wear: A torn boot, or a harsh bang when the front hits a big bump.
Tip: Fit new boots when replacing struts; a split boot shortens the life of the new strut.
See all Front Shock Bellows Boot Kit parts for the 2011 Honda CR-V 2WD
The upper of the two bolts that clamp the strut to the knuckle. An eccentric replacement bolt lets the shop adjust front camber, which is otherwise fixed.
Signs of wear: Inner or outer edge tire wear that an ordinary alignment cannot correct.
Tip: Replace one bolt per side with the eccentric bolt and have the car aligned.
See all Front End Alignment Kit parts for the 2011 Honda CR-V 2WD
The stamped steel lower arm is an A shape: it runs from the bottom of the knuckle to the cradle with a bushing at its front leg and a bracket bushing at its rear leg. The ball joint bolts to its outer end.
Signs of wear: A clunk over bumps or when braking, steering wander, uneven tire wear, or a torn ball joint boot.
Tip: The arms come with the ball joint and the bushings fitted. An alignment is needed afterwards.
Each lower arm sits in two rubber bushings, a large one at its front leg and a bracket bushing at its rear leg.
Signs of wear: A clunk when accelerating or braking, a loose feel over bumps, or the car pulling on braking.
Tip: The arm comes with new bushings, so pressing bushings alone saves money only if the arm and ball joint are good.
See all Front Control Arm Bushings parts for the 2011 Honda CR-V 2WD
The ball joint bolts to the outer end of the lower arm with three bolts. Its stud rises into the knuckle and is held by a castle nut.
Signs of wear: A knock over bumps, a loose steering feel, or grease leaking from a split boot.
Tip: 2007 to 2009 cars use one joint for both sides; 2010 and 2011 cars use a left and a right joint. The listings carry the note.
See all Front Lower Ball Joint parts for the 2011 Honda CR-V 2WD
The knuckle carries the hub and brake. The strut clamps to its top, the ball joint holds its bottom, and the outer tie rod turns it through the steering arm at its rear.
Signs of wear: Usually replaced only after damage; a bent knuckle shows up as an alignment that will not set.
Tip: The wheel bearing is pressed into the knuckle.
The front sway bar crosses the car on the rear of the cradle behind the steering rack. Long links at its ends reach up to the struts, so the bar resists body roll in corners.
Signs of wear: Heavy body roll, or a clunk from a worn link or bushing.
Tip: The bar rarely fails. Its bushings and links are the wear parts.
Two rubber bushings in clamps hold the front sway bar to the cradle.
Signs of wear: A squeak or clunk from under the front over bumps.
Tip: Buy the bushing for your bar's diameter.
See all Front Sway Bar Bushings parts for the 2011 Honda CR-V 2WD
A long link with a ball stud at each end joins each end of the front sway bar to a tab on the strut body.
Signs of wear: A knock or rattle from the front over small bumps, often the first front end noise on these cars.
Tip: Hold the stud with a hex key while turning the nut.
See all Front Sway Bar Endlinks parts for the 2011 Honda CR-V 2WD
The rack and pinion sits low on the rear of the cradle, behind the axle. Rubber boots at each end cover the inner tie rods and keep dirt out of the rack.
Signs of wear: A torn boot, a clunk when turning, or steering fluid on the boot.
Tip: Boots differ for cars built in Japan (VIN starts with J) and in North America.
See all Steering Rack Bellow parts for the 2011 Honda CR-V 2WD
The inner tie rod screws into the end of the rack under the boot and carries the outer tie rod end on its threaded end.
Signs of wear: A clunk or play in the steering, or the car wandering on the road.
Tip: Japan built and North American cars take different inner rods; check the VIN note.
See all Front Inner Tie Rod End parts for the 2011 Honda CR-V 2WD
The outer tie rod end joins the inner tie rod to the steering arm at the rear of the knuckle with a ball stud.
Signs of wear: Loose steering, a knock over bumps, or wear on the edges of the front tires.
Tip: An alignment is needed after replacing either tie rod. Japan built and North American cars take different ends.
See all Front Outer Tie Rod End parts for the 2011 Honda CR-V 2WD
A CV shaft runs from the transaxle out to each front hub, with a constant velocity joint at each end under a rubber boot.
Signs of wear: A clicking noise when turning, a vibration when accelerating, or grease thrown from a split boot.
Tip: The shafts are different lengths. Boot kits are sold for each joint.
See all CV Joint Parts - Front parts for the 2011 Honda CR-V 2WD
On all wheel drive cars the rear differential hangs from the rear cross frame on rubber mounts and drives the rear CV shafts through the prop shaft.
Not on every vehicle: All wheel drive cars only
Signs of wear: A clunk or vibration from the rear when accelerating.
Tip: Only on all wheel drive cars.
On all wheel drive cars a CV shaft runs from the rear differential out to each rear hub.
Not on every vehicle: All wheel drive cars only
Signs of wear: A clicking noise on turns, or grease thrown from a split boot.
Tip: Only on all wheel drive cars; front wheel drive cars have no rear shafts.
See all CV Joint Parts - Rear parts for the 2011 Honda CR-V 2WD
The rear knuckle carries the hub. The trailing arm bolts to a bracket at the hub, the lower arm to its bottom, the upper arm to its top and the toe link to a front ear.
Signs of wear: Usually replaced only after damage.
Tip: Mark the alignment bolts before taking the rear apart.
The bent tube trailing arm runs forward from the knuckle to a bushing at the body. The rear strut's lower eye bolts to a plate on it.
Signs of wear: A clunk from the rear under braking or over bumps, or a rear wheel that wanders.
Tip: The arm is a dealer part. Honda has a recall on 2007 to 2011 cars for corrosion where the arm mounts to the frame.
The flat stamped lower arm runs across from the rear cross member to the bottom of the rear knuckle. The rear sway bar links stand on it.
Signs of wear: A knock from the rear over bumps, or tire wear on the rear edges.
Tip: The arm is a dealer part. An alignment is needed after replacing any rear arm.
A short rod from the cross frame to the front of the knuckle sets the rear toe. The greasable adjuster has an eccentric that moves the wheel in or out.
Signs of wear: Rear tires wearing on one edge, or a car that tracks crooked.
Tip: An alignment is needed after fitting an adjuster.
See all Rear End Alignment Kit parts for the 2011 Honda CR-V 2WD
The short upper arm joins the top of the rear knuckle to the cross frame. Adjustable arms change rear camber by 2 degrees negative to 4 degrees positive.
Signs of wear: Rear tires wearing on their inside edges, a clunk from the rear, or a rear camber that cannot be set.
Tip: Fit adjustable arms when the factory arm cannot bring camber into range after lowering or wear.
The rear strut is a shock absorber with the coil spring around it. Its lower eye bolts to a plate on the trailing arm and its top goes into the rear tower.
Signs of wear: Bouncing after bumps, a floaty rear on the highway, or fluid on the body.
Tip: Replace in pairs. The same strut fits both sides.
See all Rear Shock Absorber parts for the 2011 Honda CR-V 2WD
The rear coil spring sits around the rear strut, between a seat on the strut body and the isolator under the top mount.
Signs of wear: A sagging rear corner or a clunk from a broken coil.
Tip: Replace springs in pairs.
A rubber ring between the top of the coil spring and the strut mount stops the spring from rattling against the metal.
Signs of wear: A creak or rattle from the rear on bumps.
Tip: Fit new isolators with new springs or struts.
See all Rear Coil Spring Isolator Pads parts for the 2011 Honda CR-V 2WD
A rubber bellows over the rear strut rod keeps dirt off its seal, with a bump stop inside.
Signs of wear: A torn boot, or a bang from the rear over big bumps.
Tip: Fit with new struts.
Rubber bushings, a sleeve and retainer washers hold the top of the rear strut in the body.
Signs of wear: A knock from the rear over bumps.
Tip: Fit new mount rubbers with new struts.
The rear sway bar runs across behind the rear cross member. Short links drop from its ends to the rear lower arms.
Signs of wear: Body roll in corners, or a clunk from the rear.
Tip: The bar rarely fails. Its bushings and links are the wear parts.
Two rubber bushings in clamps hold the rear bar to the cross frame.
Signs of wear: A squeak or knock from the rear.
Tip: Replace both bushings together.
See all Rear Sway Bar Bushings parts for the 2011 Honda CR-V 2WD
A short link with a ball stud at each end joins each end of the rear sway bar to a bracket on the rear lower arm.
Signs of wear: A rattle from the rear over small bumps.
Tip: The links are handed, one for each side.
See all Rear Sway Bar Endlinks parts for the 2011 Honda CR-V 2WD
The front wheel bearing is pressed into the knuckle behind the hub, which carries the wheel studs and the CV shaft splines.
Signs of wear: A hum or growl that changes with speed or when turning, play at the wheel, or an ABS light.
Tip: The bearing is pressed out of the knuckle, so it is a shop job. Use a new axle nut.
See all Front Wheel Bearing Assembly parts for the 2011 Honda CR-V 2WD
A 296 mm vented rotor on the front hub.
Signs of wear: A pulsing brake pedal, a vibration under braking, or a grooved or rusted disc.
Tip: Replace rotors in pairs and fit new pads with them.
A two piston floating caliper on a bracket behind the axle.
Signs of wear: The car pulling under braking, a dragging wheel, or a brake fluid leak.
Tip: Bleed the brakes after replacing a caliper.
See all Front Brake Caliper parts for the 2011 Honda CR-V 2WD
The pads sit in the caliper bracket either side of the rotor.
Signs of wear: A squeal from the wear indicator, grinding, or a longer stop.
Tip: Replace pads on both sides together.
The rear hub assembly bolts to the rear knuckle and carries the wheel studs and the bearing. Front wheel drive and all wheel drive cars use different hubs (the AWD hub takes the CV shaft).
Signs of wear: A hum or growl from the rear that changes with speed.
Tip: The hub bolts on as a unit. Check the notes for your drive.
See all Rear Wheel Bearing and Hub Assembly parts for the 2011 Honda CR-V 2WD
A 305 mm solid rotor on the rear hub. Its hat is a small drum for the parking brake shoes inside it.
Signs of wear: A pulsing pedal, a grooved rotor, or a parking brake that does not hold.
Tip: Cars built in the USA take a different rear rotor from those built in Japan; check the notes.
A single piston caliper on a bracket on the rear knuckle, behind the axle.
Signs of wear: A dragging rear wheel, or a leak.
Tip: The parking brake works on separate shoes, so the piston pushes straight back. Japan built cars take a different caliper from USA built cars.
See all Rear Brake Caliper parts for the 2011 Honda CR-V 2WD
The rear pads sit in the caliper bracket either side of the rotor.
Signs of wear: Squealing or grinding from the rear.
Tip: Replace pads on both sides together.
Two small shoes inside the hat of each rear rotor work the parking brake.
Signs of wear: A parking brake lever that pulls up too far, or a car that rolls with the brake set.
Tip: They sit inside the rotor hat, so the rotor comes off first.
See all Parking Brake Shoes parts for the 2011 Honda CR-V 2WD
Front sway bar links and front lower control arm bushings are the parts most often replaced, followed by the rear sway bar links, strut mounts, tie rod ends and the rear upper arms. A knock over small bumps at the front is most often a sway bar link.
No. The front uses struts, so the strut itself locates the top of the knuckle. There is one lower control arm per side. The rear does have a short upper arm on each side.
Yes for the struts, springs, arms, sway bars, brakes and tie rods. All wheel drive cars add a rear differential, a prop shaft and two rear CV shafts, and they use a different rear wheel bearing and hub, so check the fit notes on each part.
Not always. Tie rod ends, inner tie rods, steering rack boots, some brake calipers and the rear rotors are different on cars built in Japan (the VIN starts with J) and in North America. The listings carry a note for those parts.
The 2010 facelift changed the lower ball joint number. 2007 to 2009 cars take one joint for both sides and 2010 and 2011 cars take a left and a right joint. The lower arm assemblies, struts and springs did not change.
Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.