Front End Steering Rebuild Kits
Package kits bundle the wearing front end parts in one order, usually for less than buying them one by one.
This interactive diagram shows the front suspension, steering and rear suspension of the 2011 Kia Sorento. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit your Sorento, down to the side and position.
We carry parts for it Not stocked yet Hover or tap any part.
The 2011 Sorento uses MacPherson struts at the front, each bolted to the knuckle by a two bolt clevis, with the coil spring on the strut and long links from the struts down to the front sway bar. A stamped steel A shaped lower arm sits under each corner with a press-in lower ball joint, and the steering rack sits behind the front axle. The rear is a multi-link design on its own crossmember: a wide lower arm behind the axle carries the coil spring, a lower forward arm and an aluminum upper arm run out to ball joints in the knuckle, and a trailing arm runs forward from the knuckle to the body. The rear shocks are separate from the springs and sit ahead of the axle. All wheel drive models add a power transfer unit, a propshaft, a rear drive unit and two rear halfshafts, marked on the views.
We carry replacement parts for 31 of the 40 components on this diagram, 96 parts in all. See every part for the 2011 Kia Sorento.
Package kits bundle the wearing front end parts in one order, usually for less than buying them one by one.
Front struts and rear shocks for the whole vehicle in one order.
A strut with its spring, mount and bellows already assembled, so no spring compressor is needed.
The strut is the shock absorber and the upper locating part of the front corner in one. Its lower end is a clevis held to the top of the knuckle by two bolts, the coil spring sits on a seat on its tube, a tab on the tube takes the sway bar link, and its top is held in the strut tower by three studs.
Signs of wear: Bouncing after bumps, nose dive under braking, fluid on the tube, or a creak or knock from the top of the strut when turning at low speed.
Tip: Sorentos with the Sport Package take a different strut and spring assembly. A complete assembly comes with the spring and mount already fitted.
The front coil spring sits on a seat on the strut tube and pushes up against the top mount, with a rubber isolator at each end. It carries the weight of the front of the vehicle.
Signs of wear: A front corner sitting lower than the other, a broken coil end, or a clunk when turning the wheel at a stop.
Tip: The upper and lower isolators are different parts. Replace springs in pairs.
The strut mount is the rubber insulator and bearing at the top of the strut. Three studs hold it under the strut tower, and its bearing lets the strut turn with the steering.
Signs of wear: A creak from the front when turning the wheel quickly at low speed, a clunk over bumps, or a steering wheel that does not return to center. Kia replaced the front strut bearings on many 2011-2013 Sorentos for a creaking noise.
Tip: The mount is often replaced along with the strut, since the strut has to come out either way.
A plastic bellows covers the strut rod and a bump stop inside it stops the strut from bottoming out.
Signs of wear: A torn or missing bellows, or a hard thump over large bumps.
Tip: Bellows kits usually include the bump stop.
See all Front Shock Bellows Boot Kit parts for the 2011 Kia Sorento
A stamped steel A shaped arm under each front corner. Its long front leg runs forward to a vertical bushing on the front corner of the cradle, its short rear leg ends in a bushing held in a housing behind the axle, and the lower ball joint is pressed into its outer end.
Signs of wear: Clunks over bumps or under braking, steering that wanders, or uneven tire wear on the inner edge.
Tip: Complete arms come with both bushings and the ball joint fitted. Left and right arms are different.
Each lower arm has two bushings: a large vertical one at the end of its long front leg, bolted up into the cradle's front corner, and a smaller one on a front to back axis in a housing at the end of its short rear leg, behind the axle.
Signs of wear: Clunks when braking or pulling away, a shimmy at highway speed, or rubber that is cracked or torn.
Tip: The front and rear bushings are different parts.
See all Front Control Arm Bushings parts for the 2011 Kia Sorento
The ball joint is pressed into the outer end of the lower arm. Its stud points up into the bottom of the knuckle and is held by a castle nut and cotter pin.
Signs of wear: A clunk over bumps, play in the wheel when rocked top to bottom, or a torn boot.
Tip: A press-in joint needs a ball joint press to change without replacing the arm.
See all Front Lower Ball Joint parts for the 2011 Kia Sorento
The knuckle carries the hub bearing and the brake caliper. The strut clevis bolts to its top, the ball joint stud sits in its bottom, and its rear arm takes the outer tie rod end.
Signs of wear: Knuckles rarely wear out. A bent knuckle after a curb strike shows as a pull that an alignment will not fix.
Tip: Camber bolt kits replace the strut to knuckle bolts.
The front sway bar runs across the rear of the front cradle, behind the steering rack, in two rubber bushings. Its arms come forward and out to long links up to the struts.
Signs of wear: Body roll in turns or a knock over uneven bumps.
Two rubber bushings in steel clamps hold the bar to the rear of the front cradle.
Signs of wear: A squeak or knock over bumps, worst in cold weather.
Tip: The bushings fit a 24 mm bar.
See all Front Sway Bar Bushings parts for the 2011 Kia Sorento
A long link with a ball stud at each end runs from the end of the sway bar up to a tab on the strut tube.
Signs of wear: A knock from the front over small bumps, or a torn ball stud boot.
Tip: Left and right links are different parts. Replace them in pairs.
See all Front Sway Bar Endlinks parts for the 2011 Kia Sorento
Eccentric bolts that replace the strut to knuckle bolts so the front camber can be set.
Signs of wear: A front camber that cannot be brought into range after a strut or arm change.
See all Front End Alignment Kit parts for the 2011 Kia Sorento
The rack sits behind the front axle line on the rear of the front cradle. It pushes the inner tie rods left and right, with a rubber bellows over each end.
Signs of wear: A knock through the steering wheel, play in the steering, or a torn bellows letting dirt into the rack.
The inner tie rod screws into the end of the rack under the bellows and runs out to the outer tie rod end.
Signs of wear: Play in the steering, a clunk when turning, or uneven tire wear.
Tip: Set the toe after replacing one.
See all Front Inner Tie Rod End parts for the 2011 Kia Sorento
The outer tie rod end threads onto the inner tie rod and its stud fits the steering arm at the rear of the knuckle.
Signs of wear: Play in the wheel when rocked side to side, a clunk when steering, or a torn boot.
Tip: Left and right ends are different parts. Count the turns when you remove the old end, then get an alignment.
See all Front Outer Tie Rod End parts for the 2011 Kia Sorento
A CV axle runs from the transaxle to each front hub, with a boot over the joint at each end.
Signs of wear: Clicking when turning under power, a vibration when accelerating, or grease on the inside of the wheel.
Tip: Left and right axles are different parts.
See all CV Joint Parts - Front parts for the 2011 Kia Sorento
On all wheel drive models a power transfer unit on the transaxle sends drive back through a propshaft to the rear drive unit.
Not on every vehicle: Fitted only to all wheel drive models. Front wheel drive models have no power transfer unit, propshaft, rear drive unit or rear halfshafts.
Signs of wear: A whine or grinding from the front of the vehicle on AWD models.
On all wheel drive models a propshaft carries power back to the rear drive unit at the center of the rear crossmember, which drives the rear halfshafts.
Not on every vehicle: Fitted only to all wheel drive models. Front wheel drive models have no power transfer unit, propshaft, rear drive unit or rear halfshafts.
Signs of wear: A whine, shudder or clunk from the rear on AWD models.
On all wheel drive models a halfshaft runs from the rear drive unit to each rear hub.
Not on every vehicle: Fitted only to all wheel drive models. Front wheel drive models have no power transfer unit, propshaft, rear drive unit or rear halfshafts.
Signs of wear: Clicking or a vibration from the rear under power, or grease from a split boot.
See all CV Joint Parts - Rear parts for the 2011 Kia Sorento
A rubber coupler in the propshaft line on all wheel drive models.
Not on every vehicle: Fitted only to all wheel drive models; the coupler we carry is listed for 2011 and 2012.
Signs of wear: A clunk when pulling away, or a vibration on AWD models.
Tip: Listed for 2011 and 2012 AWD models.
The rear knuckle carries the hub and the rear caliper. The spring arm, the lower forward arm, the upper arm, the trailing arm and the shock all attach to it; the two front arms through ball joints at their outer ends.
Signs of wear: A clunk from the rear over bumps, or rear tires wearing on the edges.
A wide stamped arm behind the axle line. The rear coil spring sits on it, its inner end pivots on a bushing at the rear corner of the crossmember and its outer end bolts through the lower bushing in the knuckle.
Signs of wear: A clunk over bumps, a rear corner sitting low, or rust through the spring seat.
The rear coil spring sits between the spring arm and a seat on the body. The shock is separate.
Signs of wear: A rear corner sitting low, a broken coil end, or a clunk over bumps.
Tip: Replace rear springs in pairs.
A straight arm ahead of the axle line, from a bushing on the crossmember's front bracket out to a ball joint in the knuckle. The rear sway bar link bolts to it.
Signs of wear: A clunk over bumps, a worn ball joint, or rear toe that will not hold.
Eccentric cam bolts for the inner ends of the rear arms, used to set the rear camber and toe.
Signs of wear: A rear alignment that cannot be set, or a cam bolt seized by rust.
Tip: Seized cam bolts often have to be cut out, so a new kit is worth having on hand.
See all Rear End Alignment Kit parts for the 2011 Kia Sorento
An aluminum arm above the axle line, from a bushing on the rear crossmember out to a ball joint in the top of the knuckle.
Signs of wear: A clunk from the rear, a worn ball joint, or rear tires wearing on the inner edge.
Tip: Left and right upper arms are different parts.
A stamped steel arm bolted to the front of the rear knuckle and running forward and inboard to a bushing in a bracket on the body.
Signs of wear: A clunk when pulling away or braking, or a rear wheel that steers itself over bumps.
The rear shock is separate from the spring. It sits ahead of the axle with a bushed eye at each end, the lower one in a clevis on the knuckle and the upper one on a bracket on the body, leaning well inboard.
Signs of wear: Bouncing at the rear, fluid on the body, or a knock over bumps.
Tip: Replace rear shocks in pairs.
The rear sway bar runs across the front of the rear crossmember in two bushings, and short links connect its ends to the lower forward arms.
Signs of wear: Body roll at the rear or a knock over uneven bumps.
Two rubber bushings in steel clamps hold the rear bar to the crossmember.
Signs of wear: A squeak or knock from the rear over bumps.
Tip: The 2.4 L and 3.5 L models use different bar sizes, so the bushings differ by engine.
See all Rear Sway Bar Bushings parts for the 2011 Kia Sorento
A short link with a ball stud at the bar end and a bushed bolt through the lower forward arm at the other.
Signs of wear: A rattle or knock from the rear over small bumps.
See all Rear Sway Bar Endlinks parts for the 2011 Kia Sorento
A sealed bearing and hub bolted to the face of the knuckle with four bolts. The wheel studs are pressed into its flange and the CV axle is splined through it.
Signs of wear: A hum or growl that changes with speed or when turning, or play in the wheel.
See all Front Wheel Bearing and Hub Assembly parts for the 2011 Kia Sorento
The vented front rotor (300 mm) sits over the hub, clamped by the wheel.
Signs of wear: Pulsing in the pedal, grooves or a lip on the disc, or squealing.
The single piston caliper sits on its bracket at the rear of the rotor, behind the axle line, and squeezes the pads against the rotor.
Signs of wear: Pulling to one side, a sticking brake, or fluid at the caliper.
Tip: Left and right calipers are different parts.
Two pads in the caliper bracket, one each side of the rotor, with a wear sensor tab on the inner pad.
Signs of wear: Squealing from the wear indicator, grinding, or a longer pedal.
A sealed bearing and hub bolted to the rear knuckle, with the wheel speed sensor built in.
Signs of wear: A hum or growl from the rear that changes with speed.
Tip: Front wheel drive and all wheel drive models take different rear hubs; the AWD hub is splined for the halfshaft.
See all Rear Wheel Bearing and Hub Assembly parts for the 2011 Kia Sorento
The solid rear rotor (302 mm) sits over the rear hub. Its deep center hat is the drum for the parking brake shoes inside it.
Signs of wear: Pulsing, grooves, or a parking brake that does not hold.
The single piston aluminum rear caliper sits on its bracket at the rear of the rotor.
Signs of wear: A dragging rear brake or fluid at the caliper.
Tip: Left and right calipers are different parts.
Two pads in the rear caliper bracket.
Signs of wear: Squealing or grinding from the rear.
Two small shoes inside the hat of each rear rotor work as a drum brake for the parking brake.
Signs of wear: A parking brake that will not hold the vehicle on a slope.
Front sway bar links, the lower control arm bushings, lower ball joints, tie rod ends, the front strut mounts and bearings, struts and rear shocks are the usual wear parts on this suspension. Kia replaced the front strut bearings on many 2011-2013 Sorentos for a creak when turning.
No. The front uses struts, so the strut itself locates the top of the knuckle. There is one lower control arm and one lower ball joint per side. The rear does have an upper arm on each side.
No. Sorentos with the Sport Package take a different front strut and spring assembly from the others. Check the package on each strut listing before ordering.
Yes, for a few parts. The rear hubs differ, because the AWD hub is splined for the rear halfshaft, and only AWD models have the rear drive unit, propshaft and halfshafts. The rear arms, springs, shocks and brakes are shared.
Yes, after replacing tie rods, struts, control arms or rear arms. Front toe is set at the tie rods, front camber can be set with the cam bolt kits that replace the strut to knuckle bolts, and the rear has its own camber and toe kits.
Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.