Complete Front Strut Assemblies
A front strut with its spring, mount and boot already assembled, so no spring compressor is needed. AWD and FWD cars take different assemblies.
This interactive diagram shows the front suspension, steering, drive shafts and rear suspension of the 2006 Lexus RX 330. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit, down to the side.
We carry parts for it Not stocked yet Hover or tap any part.
The RX 330 uses MacPherson struts up front, each clamping the knuckle top in a two bolt clevis above an L shaped lower control arm with a bolted on ball joint. The rear is a dual link strut design: two lateral arms and a trailing arm locate each rear knuckle. On all wheel drive models a propeller shaft with a center support drives a rear differential, with a drive shaft out to each rear wheel.
We carry replacement parts for 35 of the 44 components on this diagram, 135 parts in all. See every part for the 2006 Lexus RX 330.
A front strut with its spring, mount and boot already assembled, so no spring compressor is needed. AWD and FWD cars take different assemblies.
A rear strut with its spring and mount already assembled.
Front and rear struts for the whole car in one order.
Inner and outer tie rods in one order.
A pressed steel L shaped arm. The ball joint bolts to its outer end, a short front leg pivots on a bushing at the subframe, and a long curved rear leg ends in an upright bushing at the subframe's rear corner.
Signs of wear: Clunks over bumps or under braking, wandering, or cracked bushings.
Tip: Left and right arms are different parts, and cars with the sport or performance package take their own arms. Check the fit notes.
The bushing in the arm's short front leg, on a bolt that runs front to back at the subframe.
Signs of wear: A clunk when pulling away or braking, or torn rubber.
Tip: Polyurethane sets replace both inner bushings of the arm.
See all Front Control Arm Bushings parts for the 2006 Lexus RX 330
The large upright bushing at the end of the arm's long rear leg, at the subframe's rear corner.
Signs of wear: Shimmy under braking, a clunk over bumps, or split rubber.
Tip: This bushing wears more often than any other part of the front arm. Caster correcting versions are listed.
See all Front Control Arm Bushings parts for the 2006 Lexus RX 330
The ball joint bolts to the outer end of the lower arm with one bolt and two nuts. Its stud points up into the bottom of the knuckle and is held by a castle nut and cotter pin.
Signs of wear: Clunking over bumps, uneven tire wear, or a torn boot.
Tip: Left and right joints differ. The same joints fit every 2004 to 2006 RX 330.
See all Front Lower Ball Joint parts for the 2006 Lexus RX 330
The cast knuckle carries the wheel bearing and hub. Its top sits in the strut's two bolt clevis, the ball joint stud goes into its bottom, and the tie rod joins its steering arm behind the axle.
Signs of wear: Bearing noise that a new bearing does not cure, or a bent knuckle after a curb strike.
Tip: Complete knuckle assemblies come with the bearing and hub already pressed in, so no press is needed.
See all Front Steering Knuckle Assembly parts for the 2006 Lexus RX 330
The MacPherson strut clamps the top of the knuckle in a two bolt clevis and runs up to the strut tower. It carries the coil spring, and a tab on its body holds the top of the sway bar link.
Signs of wear: Bouncing after bumps, nose dive under braking, or oil on the strut body.
Tip: Left and right struts are different parts. Cars with air suspension take other parts. Complete strut assemblies need no spring compressor.
See all Front Shock Absorber parts for the 2006 Lexus RX 330
The front coil spring sits on a seat on the strut body and pushes up against the top mount. Rubber seats sit at its ends.
Signs of wear: A sagging corner, a clunk from a broken coil end, or a squeak from a worn seat.
Tip: Spring seats and insulators are listed here. Cars with air suspension have no coil springs.
A rubber boot over the strut rod, inside the coil spring, with the bump stop at its top. It keeps dirt off the rod seal.
Signs of wear: A torn boot or a harsh bang when the suspension bottoms out.
Tip: Replace the boot and bump stop whenever the strut is replaced.
See all Front Shock Bellows Boot Kit parts for the 2006 Lexus RX 330
The rubber mount and bearing at the top of the strut, bolted to the strut tower under the hood.
Signs of wear: A knock over bumps or a creak when turning the wheel at a standstill.
Tip: Often replaced with the strut, since the strut must come out either way.
The two bolts that hold the strut's clevis to the top of the knuckle. Offset cam bolts in their place let the camber be set.
Signs of wear: Uneven wear on the inside or outside edge of the front tires.
Tip: Bolt sizes differ (15 and 17 mm). Check the fit notes, then align the car.
See all Front End Alignment Kit parts for the 2006 Lexus RX 330
The front sway bar runs across behind the subframe. Its ends bend forward to the links that rise to the struts.
Signs of wear: Body roll in corners; a broken bar is rare.
Tip: Check the links and bushings first.
Two rubber bushings in clamps hold the front bar to the subframe.
Signs of wear: A squeak or clunk over bumps.
Tip: Split bushings fit without removing the bar.
See all Front Sway Bar Bushings parts for the 2006 Lexus RX 330
A link about 250 mm long with a ball stud at each end. The top bolts to a tab on the strut body and the bottom to the end of the sway bar.
Signs of wear: A rattle or clunk over small bumps.
Tip: Hold the stud with a hex key while you turn the nut.
See all Front Sway Bar Endlinks parts for the 2006 Lexus RX 330
The front bearing is pressed into the knuckle and the hub is pressed through it.
Signs of wear: A hum or growl that changes with speed or in turns.
Tip: Pressing the bearing needs a press; a complete knuckle assembly avoids it.
See all Front Wheel Bearing Assembly parts for the 2006 Lexus RX 330
The outer tie rod end threads onto the inner rod and joins the knuckle's steering arm behind the axle.
Signs of wear: Loose steering, a clunk when turning, or a torn boot.
Tip: Count the turns when you remove it, then align the car.
See all Front Outer Tie Rod End parts for the 2006 Lexus RX 330
The inner tie rod screws into the end of the steering rack under the boot.
Signs of wear: Play in the steering or a knock over bumps.
Tip: Align the car after replacing one.
See all Front Inner Tie Rod End parts for the 2006 Lexus RX 330
A rubber boot at each end of the rack keeps dirt out of the inner tie rod joint.
Signs of wear: A torn boot or fluid at the end of the rack.
Tip: Replace the boot whenever an inner tie rod is replaced.
See all Steering Rack Bellow parts for the 2006 Lexus RX 330
The power steering rack sits behind the front axle on the subframe. Its pinion rises on the driver side to the steering column.
Signs of wear: Fluid at the boots, wander, or a knock felt in the wheel.
Tip: Align the car after any rack work.
A half shaft runs from the transaxle to each front hub. The passenger shaft is long and runs under the engine.
Signs of wear: A clicking noise in tight turns, or grease thrown from a torn boot.
Tip: Boot kits, the axle nut and complete shafts are all here.
See all CV Joint Parts - Front parts for the 2006 Lexus RX 330
The propeller shaft carries drive from the transfer case at the front to the rear differential. It runs in two pieces joined at a center support bearing under the floor.
Not on every vehicle: Fitted to all wheel drive cars only. Front wheel drive RX 330s have no rear drive shafts, differential or propeller shaft.
Signs of wear: Vibration that rises with speed, or a clunk when the drive takes up.
Tip: Not sold separately here; the center supports are.
A rubber mounted bearing in a bracket bolted to the floor holds the propeller shaft between its pieces.
Not on every vehicle: Fitted to all wheel drive cars only. Front wheel drive RX 330s have no rear drive shafts, differential or propeller shaft.
Signs of wear: Vibration or a rumble from under the middle of the car, or cracked rubber at the support.
Tip: Cars built in Japan (VIN starting with J) take a different support from Canada built cars. Mark the shaft's phasing before you take it apart.
A drive shaft runs from each side of the rear differential to the rear hub.
Not on every vehicle: Fitted to all wheel drive cars only. Front wheel drive RX 330s have no rear drive shafts, differential or propeller shaft.
Signs of wear: A click or clunk at the rear when pulling away, or grease thrown from a torn boot.
Tip: Boot kits, the rear axle nut and complete shafts are all here. The listed shaft fits cars built in Japan (VIN starting with J); check the fit notes.
See all CV Joint Parts - Rear parts for the 2006 Lexus RX 330
The rear differential hangs from the rear suspension member on rubber mounts. The propeller shaft drives its front and the rear drive shafts leave its sides.
Not on every vehicle: Fitted to all wheel drive cars only. Front wheel drive RX 330s have no rear drive shafts, differential or propeller shaft.
Signs of wear: Whine that changes with speed, or oil at the seals.
Tip: Not sold separately here.
A long rod from a bushing in a body bracket ahead of the wheel back to the knuckle's lower front, where it bolts through the knuckle bushing. It keeps the wheel from moving fore and aft.
Signs of wear: A clunk at the rear under braking or when pulling away.
Tip: All wheel drive and front wheel drive cars take different arms (Moog RK643094 AWD, RK642807 FWD). Check the fit notes.
A straight lateral link from the rear suspension member out to the bottom front of the knuckle.
Signs of wear: Uneven rear tire wear or a clunk from the rear.
Tip: Align the car after replacing any rear arm. AWD and FWD cars take different arms.
The rear lateral link from the suspension member out to the bottom rear of the knuckle. On FWD cars it has a threaded sleeve that sets the rear toe.
Signs of wear: Uneven rear tire wear.
Tip: Cars with HID headlights carry the headlight leveling sensor on one arm and take their own part. AWD and FWD cars differ too. Align the car after replacing it.
A bushing pressed into the lower front eye of the rear knuckle, where the trailing arm bolts on.
Signs of wear: A clunk or a shift at the rear over bumps, a common wear point on this car.
Tip: It presses in and out with a tool.
See all Rear Control Arm Bushings parts for the 2006 Lexus RX 330
The rear knuckle (axle carrier) carries the hub and brake. The strut clamps its top, and both lateral arms and the trailing arm bolt to its bottom.
Signs of wear: Rarely fails; check its bushing.
Tip: Not sold separately here.
The rear strut clamps the top of the knuckle in a two bolt clevis and runs up to the body. It carries the coil spring and a tab for the sway bar link.
Signs of wear: Bouncing or a floaty rear, or oil on the strut body.
Tip: AWD and FWD struts differ. Cars with air suspension take other parts.
The rear coil spring sits on a seat on the strut body, so it comes out with the strut. Rubber insulators sit at both ends.
Signs of wear: A sagging rear or a clunk from a broken coil.
Tip: Spring seat insulators are listed here. Replace springs in pairs.
The rubber mount at the top of the rear strut, bolted to the body.
Signs of wear: A knock from the rear over bumps.
Tip: Left and right mounts are listed separately. Change them with the struts.
A rubber boot over the rear strut rod with the bump stop at its top.
Signs of wear: A torn boot or a bang when the rear bottoms out.
Tip: Replace it with the strut.
The bolts that hold the rear strut's clevis to the top of the knuckle. Offset cam bolts in their place let the rear camber be set.
Signs of wear: Uneven wear on the inside edge of the rear tires.
Tip: Check the bolt size in the fit notes, then align the car.
See all Rear End Alignment Kit parts for the 2006 Lexus RX 330
The rear bar runs across behind the axle line, with its ends out to links that rise to the struts.
Signs of wear: Body roll; a broken bar is rare.
Tip: Check the links and bushings first.
Two rubber bushings in clamps hold the rear bar to the suspension member.
Signs of wear: A squeak or clunk from the rear.
Tip: AWD and FWD cars use different bar sizes, so their bushings differ. Check the fit notes.
See all Rear Sway Bar Bushings parts for the 2006 Lexus RX 330
A link with ball studs from the bar end up to a tab on the rear strut body.
Signs of wear: A rattle from the rear over small bumps.
Tip: Hold the stud with a hex key while you turn the nut.
See all Rear Sway Bar Endlinks parts for the 2006 Lexus RX 330
A bolt on hub and bearing unit on the rear knuckle, with five wheel studs. On AWD cars the rear drive shaft is splined into it.
Signs of wear: A hum from the rear that changes with speed.
Tip: AWD cars take one splined hub for both sides; FWD hubs are left and right parts.
See all Rear Wheel Bearing and Hub Assembly parts for the 2006 Lexus RX 330
A 319 mm vented rotor on the front hub.
Signs of wear: Pulsing in the pedal or a grinding noise.
Tip: Japan built cars (VIN starting with J) and Canada built cars take different part numbers. Check the fit notes.
The caliper on its bracket bolted to the knuckle.
Signs of wear: A pull to one side when braking, or a sticking pad.
Tip: Bleed the brakes after replacing one.
The pads sit in the caliper bracket either side of the rotor.
Signs of wear: Squealing, grinding, or a long pedal.
Tip: Replace pads on both sides together.
A 288 mm solid rotor on the rear hub. Its hat is a small drum for the parking brake shoes inside it.
Signs of wear: Pulsing under light braking, or a scraped rotor face.
Tip: Check the parking brake shoes when the rotor is off.
A caliper on a bracket bolted to the rear knuckle.
Signs of wear: A dragging rear brake or uneven pad wear.
Tip: The parking brake works on separate shoes, so the piston pushes straight back.
The rear pads sit in the caliper bracket either side of the rotor.
Signs of wear: Squealing or grinding from the rear.
Tip: Replace pads on both sides together.
Two small shoes inside the hat of each rear rotor work the parking brake.
Signs of wear: A parking brake that no longer holds.
Tip: They sit inside the rotor hat, so the rotor comes off first.
Sway bar links, the upright rear bushing of the front lower control arm, struts and strut mounts, and the rear knuckle bushings are the usual ones. A rattle over small bumps is most often a link.
The front suspension and steering are the same. At the rear, AWD and FWD models take different lateral arms, trailing arms, hubs and sway bar bushings, and only AWD models have rear drive shafts, a differential and a propeller shaft. Check the fit notes on each part.
No. Both ends are strut designs. Each front corner has one lower control arm and a lower ball joint, and each rear corner has two lateral arms and a trailing arm.
Yes, after tie rods, control arms, struts or rear arms. Front toe is set at the tie rods, and cam bolts at the strut clevis let you correct camber front and rear.
Some do. The parts on this diagram are for models with coil springs; struts and springs for air suspension models are different parts.
Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.