Complete Strut Assemblies
A strut with its spring, mount and boot already assembled, so no spring compressor is needed.
This interactive diagram shows the front suspension, steering and rear suspension of the 2015 Nissan Altima sedan. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit your car, down to the side and position.
We carry parts for it Not stocked yet Hover or tap any part.
The 2013 to 2018 Altima sedan uses MacPherson struts at the front, with the coil spring on the strut and a cast aluminium lower arm under each corner. The steering rack sits behind the front axle, and long links join the front sway bar to the struts. The rear is a multi-link design on its own subframe: a wide rear lower link carries the coil spring and the knuckle, a front lower link bolts to it from the subframe, an arched upper link sits on top, and the rear shocks are separate from the springs.
We carry replacement parts for 29 of the 38 components on this diagram, 86 parts in all. See every part for the 2015 Nissan Altima.
A strut with its spring, mount and boot already assembled, so no spring compressor is needed.
Front struts and rear shocks for the whole car in one order.
Package kits bundle the wearing front end parts in one order, usually for less than buying them one by one.
The strut is the shock absorber and the upper locating part of the front corner in one. Its bottom clamps to the top of the knuckle with two bolts, the coil spring sits on its perforated seat, and its top bolts into the strut tower.
Signs of wear: Bouncing after bumps, nose dive under braking, fluid on the body, or a knock from the top of the strut over rough roads.
Tip: Struts are sold bare or as a complete assembly with the spring and mount already fitted. The complete assembly needs no spring compressor.
See all Front Shock Absorber parts for the 2015 Nissan Altima
The front coil spring rides on the strut between the lower seat on the strut body and the upper seat under the mount. It holds the front of the car at its ride height.
Signs of wear: A front corner sitting lower than the other, a clunk over bumps from a broken end coil, or tires rubbing on full lock.
Tip: Springs are replaced in pairs. A spring compressor is needed unless you fit a complete strut assembly.
A rubber seat sits between the bottom coil of the front spring and the lower seat on the strut, so the spring does not rattle against the metal.
Signs of wear: A creak or tick from the front when turning the wheel or going over bumps.
Tip: Replace the seats whenever the springs or struts come apart.
See all Front Coil Spring Isolator Pads parts for the 2015 Nissan Altima
The strut mount bolts the top of the strut to the body. It holds a bearing so the strut and spring can turn with the steering, and rubber to keep road noise out of the car.
Signs of wear: A clunk or creak from the top of the strut when turning, or steering that springs back unevenly.
Tip: Mounts are often replaced with the struts, since the strut has to come out anyway.
A rubber bellows covers the strut rod above the spring seat and keeps dirt off its seal. A bump stop inside it cushions the strut at full compression.
Signs of wear: A torn boot, or a harsh bang when the front hits a big bump.
Tip: Fit new boots when replacing struts; a split boot shortens the life of the new strut.
See all Front Shock Bellows Boot Kit parts for the 2015 Nissan Altima
The upper of the two bolts that clamp the strut to the knuckle. An eccentric replacement bolt lets the shop adjust front camber, which is otherwise fixed.
Signs of wear: Inner or outer edge tire wear that an ordinary alignment cannot correct.
Tip: Replace one bolt per side with the eccentric bolt and have the car aligned.
See all Front End Alignment Kit parts for the 2015 Nissan Altima
The cast aluminium lower arm runs from the bottom of the knuckle to the subframe. Its front leg ends in a small bushing on a fore and aft bolt, and its rear leg sweeps back to a large upright bushing. The ball joint is part of the arm.
Signs of wear: A clunk over bumps or when braking, steering wander, uneven tire wear, or a torn ball joint boot.
Tip: The 2015 to 2017 arms come with the ball joint and both bushings fitted. An alignment is needed afterwards.
Each lower arm sits in two rubber bushings: a small one at the front leg and a large upright one at the rear leg.
Signs of wear: A clunk when accelerating or braking, a loose feel over bumps, or the car pulling on braking.
Tip: The arm comes with new bushings, so pressing bushings alone saves money only if the arm and ball joint are good.
See all Front Control Arm Bushings parts for the 2015 Nissan Altima
The ball joint is pressed into the outer end of the lower arm. Its stud rises into the knuckle, where a pinch bolt holds it.
Signs of wear: A knock over bumps, a loose steering feel, or grease leaking from a split boot.
Tip: On this car the joint is sold as part of the lower arm.
The knuckle carries the hub and brake. The strut clamps to its top, the ball joint holds its bottom, and the outer tie rod turns it through the steering arm at its rear.
Signs of wear: Usually replaced only after damage; a bent knuckle shows up as an alignment that will not set.
Tip: The hub bolts to the knuckle from behind with four bolts.
The front sway bar crosses the car on the subframe behind the engine. Long links at its ends reach up to the struts, so the bar resists body roll in corners.
Signs of wear: Heavy body roll, or a clunk from a worn link or bushing.
Tip: The bar rarely fails. Its bushings and links are the wear parts.
Two rubber bushings in clamps hold the front sway bar to the subframe.
Signs of wear: A squeak or clunk from under the front over bumps.
Tip: Buy the bushing for your bar's diameter: the sedan bar is 21 mm on most cars, and a 23 mm set is listed too.
See all Front Sway Bar Bushings parts for the 2015 Nissan Altima
A long link with a ball stud at each end joins each end of the front sway bar to a tab on the strut body.
Signs of wear: A knock or rattle from the front over small bumps, often the first front end noise on these cars.
Tip: Hold the stud with a hex key while turning the nut.
See all Front Sway Bar Endlinks parts for the 2015 Nissan Altima
The rack and pinion sits on the subframe behind the axle. Rubber boots at each end cover the inner tie rods and keep dirt out of the rack.
Signs of wear: A torn boot, a clunk when turning, or steering fluid on the boot.
Tip: Replace a torn boot quickly; grit in the rack wears it fast.
See all Steering Rack Bellow parts for the 2015 Nissan Altima
The inner tie rod screws into the end of the rack under the boot and carries the outer tie rod end on its threaded end.
Signs of wear: A clunk or play in the steering, or the car wandering on the road.
Tip: Count the turns when you unscrew the outer end and set the toe afterwards.
See all Front Inner Tie Rod End parts for the 2015 Nissan Altima
The outer tie rod end joins the inner tie rod to the steering arm at the rear of the knuckle with a ball stud.
Signs of wear: Loose steering, a knock over bumps, or wear on the edges of the front tires.
Tip: An alignment is needed after replacing either tie rod.
See all Front Outer Tie Rod End parts for the 2015 Nissan Altima
A CV shaft runs from the transaxle out to each front hub, with a constant velocity joint at each end under a rubber boot.
Signs of wear: A clicking noise when turning, a vibration when accelerating, or grease thrown from a split boot.
Tip: The right shaft is longer, since the transaxle sits on the driver side. Boot kits are sold for each joint.
See all CV Joint Parts - Front parts for the 2015 Nissan Altima
The aluminium rear knuckle carries the hub. Its arched bottom bolts over the outer end of the rear lower link with two bolts, and the upper link joins its top.
Signs of wear: Usually replaced only after damage.
Tip: Mark the alignment bolts before taking the rear apart.
The wide rear lower link carries the coil spring in a pocket. Its narrow inner end sits on an alignment bolt at the subframe, its outer end carries the knuckle, and the front lower link and the sway bar link bolt to it.
Signs of wear: A knock or rattle from the rear over bumps, or a rear wheel with a lot of positive camber. Nissan bulletin NTB21-045 replaces both rear lower links for this.
Tip: Removing it means compressing the coil spring. Ask a Nissan dealer whether a campaign or extended coverage applies to your car first.
A rubber bushing in the inner eye of each rear lower link takes the alignment bolt.
Signs of wear: A clunk from the rear over bumps, or rear tire wear.
Tip: Mark the alignment bolt washer before removing the bolt, so the toe stays close.
See all Rear Control Arm Bushings parts for the 2015 Nissan Altima
The rear coil spring stands in the pocket of the rear lower link, with rubber seats at each end, and pushes up against a bracket on the body.
Signs of wear: A sagging rear corner or a clunk from a broken coil.
Tip: The spring has a painted orientation mark; refit it the same way.
The front lower link runs from its own alignment bolt at the subframe out to the rear lower link, where two upright bushings bolt it to the link's front edge.
Signs of wear: A clunk from the rear, a rear end that steers itself over bumps, or uneven rear tire wear.
Tip: The links are made for each side. Moog lists an old and a new design; either fits.
The arched upper link joins the top of the rear knuckle to the subframe. An eccentric bolt at its inner end sets rear camber.
Signs of wear: Rear tires wearing on their inside edges, or a clunk from the rear.
Tip: An adjustable replacement arm can correct rear camber on a lowered car.
A rubber bushing in each end of the upper link.
Signs of wear: A clunk from the rear, or rear camber that will not stay set.
Tip: Polyurethane bushing sets cover every rear link on these cars.
See all Rear Control Arm Bushings parts for the 2015 Nissan Altima
The rear shock is separate from the spring, with a clevis at its lower end and a stem at its upper end.
Signs of wear: Bouncing after bumps, a floaty rear on the highway, or fluid on the body.
Tip: Replace shocks in pairs.
See all Rear Shock Absorber parts for the 2015 Nissan Altima
Rubber bushings, a sleeve and retainer washers hold the top stem of the rear shock.
Signs of wear: A knock from the rear over bumps.
Tip: Fit new mount rubbers with new shocks.
See all Rear Shock Bushings parts for the 2015 Nissan Altima
The rear sway bar runs across behind the subframe. Short links drop from its ends to the rear lower links.
Signs of wear: Body roll in corners, or a clunk from the rear.
Tip: The SR trim from 2016 has its own rear links (sport tuned suspension).
Two rubber bushings in clamps hold the rear bar to the subframe.
Signs of wear: A squeak or knock from the rear.
Tip: Replace both bushings together.
See all Rear Sway Bar Bushings parts for the 2015 Nissan Altima
A short link with a ball stud at each end joins each end of the rear sway bar to a bracket on the rear lower link.
Signs of wear: A rattle from the rear over small bumps.
Tip: The SR with sport tuned suspension (2016 on) takes its own links; check the notes.
See all Rear Sway Bar Endlinks parts for the 2015 Nissan Altima
The hub assembly bolts to the knuckle and holds the wheel studs, the bearing and the CV shaft splines.
Signs of wear: A hum or growl that changes with speed or when turning, play at the wheel, or an ABS light.
Tip: The hub bolts on from behind, so no press is needed. Use a new axle nut.
See all Front Wheel Bearing and Hub Assembly parts for the 2015 Nissan Altima
A 296 mm vented rotor on the front hub.
Signs of wear: A pulsing brake pedal, a vibration under braking, or a grooved or rusted disc.
Tip: Replace rotors in pairs and fit new pads with them.
A single piston floating caliper on a bracket ahead of the axle.
Signs of wear: The car pulling under braking, a dragging wheel, or a brake fluid leak.
Tip: Bleed the brakes after replacing a caliper.
The pads sit in the caliper bracket either side of the rotor. The pads we sell have a slot and a wear sensor tab.
Signs of wear: A squeal from the wear sensor, grinding, or a longer stop.
Tip: Replace pads on both sides together.
The rear hub assembly bolts to the rear knuckle and carries the wheel studs and the bearing.
Signs of wear: A hum or growl from the rear that changes with speed.
Tip: The hub bolts on as a unit.
See all Rear Wheel Bearing and Hub Assembly parts for the 2015 Nissan Altima
A 292 mm solid rotor on the rear hub. Its hat is a small drum for the parking brake shoes inside it.
Signs of wear: A pulsing pedal, a grooved rotor, or a parking brake that does not hold.
Tip: Check the parking brake shoes when the rotor is off.
A single piston caliper on a bracket on the rear knuckle.
Signs of wear: A dragging rear wheel, or a leak.
Tip: The parking brake works on separate shoes, so the piston pushes straight back.
The rear pads sit in the caliper bracket either side of the rotor.
Signs of wear: Squealing or grinding from the rear.
Tip: Cars with solid rear rotors take the solid rotor pads; check the notes.
Two small shoes inside the hat of each rear rotor work the parking brake.
Signs of wear: A parking brake lever that pulls up too far, or a car that rolls with the brake set.
Tip: They sit inside the rotor hat, so the rotor comes off first.
See all Parking Brake Shoes parts for the 2015 Nissan Altima
Front sway bar links and front lower control arms are the parts most often replaced, followed by the rear lower links, strut mounts and tie rod ends. A knock over small bumps at the front is most often a sway bar link.
Very often the rear lower link, the wide arm that holds the rear spring. Nissan bulletin NTB21-045 covers replacing both rear lower links for this noise, so ask a Nissan dealer whether a campaign or extended coverage applies before buying parts. Worn rear sway bar links make a lighter rattle.
No. The front uses struts, so the strut itself locates the top of the knuckle. There is one lower control arm per side, with the ball joint built into the arm. The rear does have an upper link on each side.
Yes, after replacing tie rods, struts, front lower arms or any rear link. Rear toe and camber are set at eccentric bolts on the rear links, so mark them before you take the rear apart.
The 2015 to 2017 Altima sedan shares the parts on this diagram. The 2013 and 2014 sedans use an earlier front lower arm, 2018 cars take a different front rotor, and the 2013 coupe is the older generation with its own suspension, so check the fit notes on each part.
Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.