Ball Joint Dust Boots - AM General Hummer - 9.13136

  • 9.13136 360image 1
  • 9.13136 Front Ball Joint Dust Boots
  • 9.13136 Front Ball Joint Dust Boots
  • 9.13136 Front Ball Joint Dust Boots
  • 9.13136 Front Ball Joint Dust Boots
  • 9.13136 Front Ball Joint Dust Boots
  • 9.13136 360image large 1

Front Ball Joint Dust Boots

Manufacturer: Energy Suspension
Part Number: 9.13136

:(?)
Black
Red

:(?)
Free Lifetime Warranty Upgrade
Price: $41.49

check_box In Stock check_box Ships Immediately


  • 2 - 13025 -Upper Ball Joint Boots
  • 2 - 13026- Lower Ball Joint Boots
  • 2 - Metal Retaining Clips for Upper Boots
  • 2 - Metal Retaining Clips for Lower Boots
  • Energy Suspension warrants its products against defects in workmanship and material for 7 years or 750,000 miles when used on passenger cars and light trucks. Products that have been abused, altered, or incorrectly installed are not covered. Energy Suspension will replace defective products or component parts, if inspection for factory personnel determines the part to be defective. Warranty replacement covers only the product. Labor claims, time loss, or freight charges will not be honored.

question_answer Ask us a Question

FitmentFront Ball Joint Dust Boots 9.13136 fits these vehicles:
Details
Polyurethane Front Ball Joint Dust Boots
Finally, someone has made a replacement ball joint dust boot! No more expenseor cost worries when the boot wears out or is damaged either from installation or from day to day use.

Ball Joint Dust Boots - AM General Hummer - 9.13136

Pin Opening Diameter Base Opening Diameter Height of Boot Piece Number
19mm (0.75 inch) 45.10mm (1.775 inch) 42.33mm (1.666 inch) 13025*
21.25mm (0.836 inch) 51mm (2 inch) 40.3mm (1.585 inch) 13026
* The 13025 piece can be bought separately

Here is our complete list of universal dust boots.

Polyurethane Front Ball Joint Dust Boots
  • Repair torn and worn out ball joint boots without having to buy the entire ball joint just to get the boot.
  • Adds both durability and that custom look attention custom show car builders!
  • Lasts longer, seals better and looks great for show vehicles!
  • Resist damage from rocks, sand, water, road salt, and oils better than many other O.E.M. rubber boots.
  • Made of Energy's HYPER FLEX performance polyurethane for added performance and durability.
Footnotes
  • One Set Will Cover the Left and Right Side

Energy Suspension Polyurethane Universal Dust Boots

Importance of Dust Boots

Many of you are finding out that the rubber boot on your ball joint or tie rod has rotted away or has split. These boots are extremely important for the suspension of your vehicle. Fortunately, Energy Suspension makes Universal Dust boots that will fit most vehicles. These dust boots are made of polyurethane and are far more durable than rubber. This will seal your boot to retain the grease in the joint, as well as protecting the joint from dirt, sand, water, and snow.

Energy Suspension Universal Dust Boots
Energy Suspension Universal Dust Boots

How to get your measurements

In order to select the proper boot, you will first need to grab a few measurements. The best way to do this is with a set of digital calipers. You will need to measure the diameter of the base where the boot will sit, the diameter of the shaft (also called the Pin Opening Diameter) and the height of the boot. Once you have gotten to your tie rod end measure these three spots. Be sure to be as exact as possible and to write down your measurements. If you have any trouble getting these measurements, give our customer service team at DST a call.

It is important to note that you do not want to choose a boot that is bigger than your measurements. You want to choose a boot that is just slightly smaller than the measurements you obtained. The elasticity of the polyurethane will allow the hole to stretch and grip the joint tightly. If you choose a boot that is too large there will be a gap which lets in debris.

Now that you have these measurements, you can verify that this is the boot that you need. If you find that your measurements do not match this boot, go to our Universal Dust Boot page to match a part to your measurements.

Choose your design

Energy Suspension offers an alternative to the traditional round bushing. There is an octagon shaped dust boot available as an option. The octagonal boots have the same specifications and perform the exact thing. They just offer a more unique look.

Energy Suspension Universal Dust Boots
Energy Suspension 9.13136

Product Reviews for Ball Joint Dust Boots - AM General Hummer - 9.13136

5 Star (11)
92%
4 Star (1)
8%
3 Star (0)
0%
2 Star (0)
0%
1 Star (0)
0%
starstarstarstarstar

Energy Suspension 9.13136

5 out of 5 based on 12 user reviews. Write a Review

B
verified_user

starstarstarstarstar" Heavy Duty "

The rubber on my lower ball joints didnt seem to hold up as long. Willing to see if these can impress me.

verified_user Verified Buyer - - . Energy Suspension 9.13136 - 5 out of 5
S
verified_user

starstarstarstarstar" very good product, looks like it will last a long time "

I got these for a forklift steering ram, very hard to find big sizes anywhere else, had to enlarge the shaft hole slightly then installed nicely and should keep the dust-out.

verified_user Verified Buyer - - . Energy Suspension 9.13136 - 5 out of 5
S
verified_user

starstarstarstarstar" Great "

The parts work great had no issue with them.

verified_user Verified Buyer - - . Energy Suspension 9.13136 - 5 out of 5
R
verified_user

starstarstarstarstar" Great "

The parts were used on a different application than ball joints and saved us several hundred dollars over what we would have had to do to complete the repair.

verified_user Verified Buyer - - . Energy Suspension 9.13136 - 5 out of 5

question_answer Customer Questions and Answers


Question:
Does part number 9.13136 come with 4 dust boots as pictured?
Answer:
Yes, part number 9.13136 will come with everything shown in the picture.