add_shopping_cart Suggested Parts 2keyboard_arrow_down
MOOG parts come greased from the factory, but should also be greased at the time of installation. After installation, MOOG recommends greasing these parts at each oil change for the best service life.
Out of grease? No problem we've got you covered with this Mystik Multi-Purpose Grease tube refill.
lock Warranty Information keyboard_arrow_down
Moog fulfills their warranty through their individual dealers. That means that in order to receive warranty support, you will have to refer back to the original dealer you purchased the part from. Be sure to check the dealer's warranty support before you buy the part to make sure that they will properly support the warranty. If a dealer will only refer you back to the manufacturer in order to receive warranty support, then you may not actually have any warranty at all.
Moog Premium Steering Components carry a Limited Lifetime Warranty. Moog R-Series Control Arms, Hub Assemblies, and Strut Assemblies carry a 3 Year Warranty.
Moog warranties their parts to be free of defects in materials and/or workmanship during these timeframes as measured from the date of purchase.
If a Moog part should fail due to materials or manufacturing defect while under warranty, we will provide a replacement of the part upon return of the defective part.
moog-k7455 | Front Lower Ball Joint | 2003-2006 Dodge Sprinter 2500
Moog has really outdone themselves with this ball joint, made to target the things that have been causing the problems with your vehicle.
Turn Your Weak Ball Joint into a Ball Joint Worthy of Your Fleet
Hard Time Getting Your Ball Joint Out?
Whether you manage a fleet of Dodge Sprinters or you only have one for your business the DST parts experts know you've been having a little bit of trouble out of it lately. The problem is that the OE ball joint for your fleet vehicle just wasn't made for the high demands you require out of it. This is a problem for you because, whether you have one or one hundred, they all need to be working correctly. So how do you solve this problem you ask? Well, look no further than Moog's ball joint K7455, made specifically for the high demands of your fleet vehicle.
Small Stud Diameters aren't Good Enough for Your Sprinter
We all know that your fleet vehicle is big and carries heavy loads, as it needs to. However, the OE design of the Sprinter didn't account for the high demands of this vehicle. First of all the OE ball joint isn't serviceable. This doesn't give the OE ball joint the ability to flush out the harmful road contaminants that can lead to premature wear. It also has a plastic bearing design with a 1.25" ball stud diameter. This is a very small stud diameter for a vehicle of this size and for the loads you expect it to carry. All of this leads to premature wear, which in turn leads to the problems you've been having.
It was a Pain Getting the Stud Out
No matter if you took your Dodge to a mechanic or if you have an in-house mechanic, you have found out it's very difficult to get the stud out of the knuckle. So much so that the stud might have had to be cut off to get it out of the knuckle. It is because of the high amount of torque that has to be applied to the stud nut, a whopping 210 foot-pounds of torque. This pulls the stud with extreme force, locking the stud into the knuckle. Making it all but impossible to get out without having to cut the stud.
Moog Solves all the Problems
Moog has really outdone themselves with this ball joint, made to target the things that have been causing you problems with your vehicle. Moog's K7455 is such a ball joint. Typically Moog will oversize the ball stud for vehicles like the Sprinter, but the ball joint housing's outside diameter is too small. This limits the size Moog can make the ball stud. So in order to gain the additional strength that Moog expects out of their parts, they heat treated the ball stud. Moog has also added a powdered-metal gusher bearing that will not deform under the heavy loads of your fleet vehicle, as the OE joint would. The dust boot on K7455 is made with polychloroprene. This boot has a built-in grease-relief valve, providing a sealed, serviceable part that flushes out the harmful road contaminates which leads to premature wear.
Moog has Confidence in this Part
The only thing you'll need to service Moog's K7455 is a "needle adapter" for your grease gun since Moog uses a low profile "pin" style grease fitting. Moog's problem solver lives up to their title. They have not only solved all the problems the OE design had, but they have also made it better in every way. The experts at DST feel the confidence Moog has in their parts when they add a lifetime warranty to K7455, and we're sure you will too.
Product Reviews for moog-k7455 | Front Lower Ball Joint | 2003-2006 Dodge Sprinter 2500
- 5 Star (0)
- 4 Star (0)
- 3 Star (0)
- 2 Star (1)
- 1 Star (0)
starstarstar_borderstar_borderstar_border" Ok "
There wasnt any grease fitting so the grease tried up in 30,000 miles my OEM sprinter front lower ball joints lasted 11 Years and 150k miles . Dont Buy Any Type Of Ball joint that doesnt have a way to Add more grease. Editor Note: k7455 is greaseable. For clearance the ball joint uses a recessed grease zerk. You have to use a grease needle to grease this ball joint.verified_user Verified Buyer - Tim burnett - . MOOG moog-k7455 - 2 out of 5