moog-k80222 | Front Sway Bar Bushings - 21.59mm | Ford E-250 03-07

  • moog-k80222 Front Sway Bar Bushings - 21.59 mm (0.85 inch)
  • moog-k80222 Front Sway Bar Bushings - 21.59 mm (0.85 inch)

Front Sway Bar Bushings - 21.59 mm (0.85 inch)

Manufacturer: MOOG
Part Number: moog-k80222
Price: $21.08

check_box In Stock check_box Ships Immediately


Suggested part for moog-k80222: dll122
dll122 Front Sway Bar Lateral Locks - 21-22mm
DST's lateral locks prevent sway bar movement and fits OE and aftermarket bars.

  • Moog fulfills their warranty through their individual dealers. That means that in order to receive warranty support, you will have to refer back to the original dealer you purchased the part from. Be sure to check the dealer's warranty support before you buy the part to make sure that they will properly support the warranty. If a dealer will only refer you back to the manufacturer in order to receive warranty support, then you may not actually have any warranty at all.

    WARRANTY:

    Moog Premium Steering Components carry a Limited Lifetime Warranty. Moog R-Series Control Arms, Hub Assemblies, and Strut Assemblies carry a 3 Year Warranty.

    Moog warranties their parts to be free of defects in materials and/or workmanship during these timeframes as measured from the date of purchase.

    If a Moog part should fail due to materials or manufacturing defect while under warranty, we will provide a replacement of the part upon return of the defective part.

    Wearable RUBBER parts are not covered under warranty (Dust boots, bushings, bump stops, etc.)

question_answer Ask us a Question

FitmentFront Sway Bar Bushings - 21.59 mm (0.85 inch) moog-k80222 fits these vehicles:
Details

moog-k80222 | Front Sway Bar Bushings - 21.59mm | Ford E-250 03-07

Problem Solver Design attaches sway bar to Twin I Beam Axle.

A patent-pending design eliminates rubber wear and bond failures associated with the OE design

Moog Problem Solver: K80222

The Problem: There's a knocking noise from the front end of my Ford

The noise can be caused by two types of failure. The first is when the sway bar moves inside the axle bushing during normal suspension movement. This causes the bar to slowly wear through the OE rubber bushing material. When it's worn down enough it will come into contact with the outer steel shell-metal to metal contact causing a noise. The second type of failure occurs when the bond between the rubber bushing and steel shell fails, allowing the rubber bushing to move along the sway bar. Noises coming from your suspension can be aggravating and here at DST we understand that. We have a solution for you: Moog Problem Solver K80222.

K80222 Image One
K80222 Image Two

The Solution: Moog's Problem Solver: K80222

Moog's line of problem solver parts target factory defects or poor original design, replacing them with a better more durable part. Moog has engineered front sway bar bushings with a patent-pending design that eliminates rubber wear and bond failures associated with the OE design: K80222

Enhanced Durability and Service Life

Moog engineered K80222 with premium polyurethane material for enhanced durability and service life. Because these sway bar bushings were built with polyurethane they are unaffected by oils, alkalis, ozone, hydrocarbons and can withstand extreme weather. This Moog Problem Solver reduces sway in turns, eliminates noise caused by metal on metal contact. If you needed another reason to call DST's customer service and order K80222, add easy installation to the list of many benefits.

K80222 Image Four
MOOG moog-k80222

Product Reviews for moog-k80222 | Front Sway Bar Bushings - 21.59mm | Ford E-250 03-07

5 Star (3)
100%
4 Star (0)
0%
3 Star (0)
0%
2 Star (0)
0%
1 Star (0)
0%
starstarstarstarstar

MOOG moog-k80222

5 out of 5 based on 3 user reviews. Write a Review

S
verified_user

starstarstarstarstar" Looked good "

using the silicon lube they popped in with modest pressure..

verified_user Verified Buyer - - . MOOG moog-k80222 - 5 out of 5
R
verified_user

starstarstarstarstar" Great "

I like the poly sway bar bushings over the original rubber. You will need a press or large C clamp to install.

verified_user Verified Buyer - - . MOOG moog-k80222 - 5 out of 5
M
verified_user

starstarstarstarstar

Very easy to install

verified_user Verified Buyer - - . MOOG moog-k80222 - 5 out of 5
Fitment for moog-k80222
MakeModelYear RangePositionDrive WheelQuantity RequiredEngine BaseEngine VINEngine Designation
FordE-1502007-2003Front To Axle Quantity 1
FordE-150 Club Wagon2005-2003Front To Axle Quantity 1
FordE-150 Econoline2002-1992Front To Axle Quantity 1
FordE-150 Econoline Club Wagon2002-1992Front To Axle Quantity 1
FordE-2502007-2003Front To Axle Quantity 1
FordE-250 Econoline2002-1992Front To Axle Quantity 1
FordE-350 Club Wagon2005-2003Front To Axle Quantity 1
FordE-350 Econoline1998-1992Front To Axle Quantity 1
FordE-350 Econoline Club Wagon2002-1992Front To Axle Quantity 1
FordE-350 Super Duty2007-1999Front To Axle Quantity 1

question_answer Customer Questions and Answers


Question:
Does the sleeve on my E350 need to be removed before installation for part number k80222?
Answer:
Yes, for part number k80222, you will need to remove the sleeve.

Question:
Do I need to remove the entire stock bushing, outer shell and all for the install of the moog-k80222?
Answer:
You will need to remove the entire stock bushings, Outer shell and all for the install of the moog-k80222.

Question:
Do I leave the metal shell of the original bushing in the axle when I install the moog-k80222 bushings?
Answer:
On the moog-k80222 Bushing kit, you will want to remove the outer shell of the original bushing as well. These bushings will not require the use of that original outer shell like other polyurethane bushings.

Question:
Will I need to reuse the OE metal sleeve on part number k80222?
Answer:
Yes, you will need to reuse you OE metal sleeve for part number k80222.

Question:
Do you need to also remove the steel sleeve in the I-beam before installing these or just the old rubber bushings?
Answer:
Remove the sway bar by unbolting the sway bar frame brackets and sliding the bar out of the axle bushings, remove the oem sway bar axle bushings from the axle. https://fme-cat.com/livedocs/AXCF4501.pdf