Front End Steering Rebuild Kits
Package kits bundle the wearing front end parts in one order, usually for less than buying them one by one.
This interactive diagram shows the front suspension, steering, driveline and rear suspension of the 2005 Jeep Liberty. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit, down to the side and position.
We carry parts for it Not stocked yet Hover or tap any part.
The 2002 to 2007 Liberty has independent front suspension: a wide lower control arm and a forged upper control arm at each corner, with a coilover strut whose fork bolts to the lower arm, and rack and pinion steering ahead of the front wheels. The rear is a solid axle on coil springs, held by two lower arms and a single A shaped upper arm with a ball joint on top of the differential, with a sway bar bolted to the lower arms. The diagram is drawn from a four wheel drive model; the two wheel drive Liberty has no front differential or front CV axles.
We carry replacement parts for 34 of the 40 components on this diagram, 87 parts in all. See every part for the 2005 Jeep Liberty.
Package kits bundle the wearing front end parts in one order, usually for less than buying them one by one.
Front and rear shock sets for the whole vehicle.
Both rear driveshaft U-joints in one package.
Spacer lifts that raise the front struts and the rear coils.
The lower ball joint presses into the bottom of the steering knuckle. Its stud points down through a tapered hole in the tip of the lower control arm.
Signs of wear: Clunks over bumps, a loose front end, or play when the wheel is rocked top to bottom with the vehicle on a jack.
Tip: The joint changed for 2005: the 2002 to 2004 Liberty takes a different number, so order by year. It presses into the knuckle, not the arm.
See all Front Lower Ball Joint parts for the 2005 Jeep Liberty
A forged A shaped arm that holds the top of the knuckle. The upper ball joint is part of the arm, and the coilover strut passes up through its middle.
Signs of wear: Clunks, torn bushings, or a worn upper ball joint. The joint is not sold on its own, so the arm is replaced as an assembly.
Tip: The same upper arm fits every 2002 to 2007 Liberty.
A wide ribbed A arm under each corner. Its two bushings pivot on the front and rear crossmembers under the engine, and the strut fork bolts to its rear leg.
Signs of wear: Clunks over bumps or under braking, torn bushings, or a car that wanders.
Tip: Left and right arms are different parts. The 2002 and 2003 arms were recalled in salt belt states for corrosion.
Rubber bushings in the two eyes of the upper control arm.
Signs of wear: Clunks, steering that shifts under braking, or cracked rubber at the eyes.
Tip: Polyurethane kits press into the original arm.
See all Front Control Arm Bushings parts for the 2005 Jeep Liberty
Rubber bushings in the front and rear eyes of the lower control arm, on bolts through the crossmembers.
Signs of wear: Clunks over bumps or on braking, or cracked rubber at the eyes.
Tip: The bolts carry the alignment cams, so mark them before you take them out.
See all Front Control Arm Bushings parts for the 2005 Jeep Liberty
The bushing in the bottom eye of the strut fork, where the fork bolts to the rear leg of the lower control arm.
Signs of wear: A knock from the front over small bumps.
Tip: Check it whenever the strut is out; it is a common source of front end clunks.
See all Front Control Arm Bushings parts for the 2005 Jeep Liberty
The knuckle carries the hub and caliper, holds both ball joints, and has the steering arm at the front for the outer tie rod.
Signs of wear: A bent knuckle after a curb strike, or a worn lower ball joint bore.
Tip: The lower ball joint presses into the knuckle, so it is pressed out with the knuckle on the bench.
The front shock and coil spring are one coilover strut. A fork at its bottom bolts to the lower arm, and four studs at its top bolt up under the battery tray.
Signs of wear: Bouncing after bumps, nose dive under braking, oil on the body, or a clunk from the top mount.
Tip: A complete strut assembly with the spring and mount saves using a spring compressor.
See all Front Shock and Coil Spring Assembly parts for the 2005 Jeep Liberty
The coil spring around the front strut carries the front of the vehicle.
Signs of wear: A sagging front, uneven height side to side, or a broken coil.
Tip: Spring rates differ by trim and engine. Replace them in pairs.
A rubber pad on the lower spring seat of the strut that stops the coil rattling against the seat.
Signs of wear: A squeak or creak when turning or over bumps.
Tip: Replace it whenever the spring is off the strut.
See all Front Coil Spring Isolator Pads parts for the 2005 Jeep Liberty
The top plate of the strut, with four studs up through the body under the battery tray.
Signs of wear: A clunk or knock from the top of the strut over bumps.
Tip: Left and right mounts are different parts.
A steel bar across the front of the vehicle, ahead of the front crossmember, linking the two lower arms to reduce body roll.
Signs of wear: Body roll, or a clunk if a bushing or link is worn.
Tip: The bar is 30.5 mm (1.20 in) on every 2002 to 2007 Liberty.
Two bushings clamp the front sway bar under the body rails.
Signs of wear: Clunks or squeaks over bumps.
Tip: They are for the 30.5 mm bar.
See all Front Sway Bar Bushings parts for the 2005 Jeep Liberty
A short link with a rubber eye at each end, from the end of the sway bar down to the front leg of the lower control arm.
Signs of wear: A clunk or rattle over small bumps.
Tip: Replace both sides together.
See all Front Sway Bar Endlinks parts for the 2005 Jeep Liberty
Cam bolts and shims that set the front camber and caster.
Signs of wear: Uneven tire wear or a pull after suspension work.
Tip: Fit them with an alignment.
See all Front End Alignment Kit parts for the 2005 Jeep Liberty
The outer tie rod end joins the inner tie rod to the steering arm at the front of the knuckle.
Signs of wear: Loose steering, wander, or uneven tire wear.
Tip: Count the turns when you take it off, then get an alignment.
See all Front Outer Tie Rod End parts for the 2005 Jeep Liberty
The inner tie rod screws into the end of the steering rack inside the boot.
Signs of wear: A clunk when turning, or play in the steering.
Tip: The inner tie rod changed for 2006, so the 2002 to 2005 and 2006 to 2007 Liberty take different parts.
See all Front Inner Tie Rod End parts for the 2005 Jeep Liberty
Rubber boots at each end of the steering rack keep dirt off the inner tie rods.
Signs of wear: A torn boot, or grease thrown on the crossmember.
Tip: Replace a torn boot before the inner tie rod wears.
The rack and pinion steering gear sits across the vehicle just behind the front crossmember, ahead of the front wheels.
Signs of wear: Leaks, a clunk on turning, or heavy steering.
Tip: The rack mounts on rubber bushings, which can be replaced on their own.
Rubber bushings in the two clamps that hold the steering rack to the front crossmember.
Signs of wear: A clunk or shift in the steering when turning in or over bumps.
Tip: Change both at once.
See all Steering Rack Bushings parts for the 2005 Jeep Liberty
The CV axle drives the front wheel from the front differential (driver side) or from the intermediate shaft (passenger side).
Not on every vehicle: Four wheel drive models only; the 2WD Liberty has no front differential, CV shafts or front driveshaft.
Signs of wear: Clicking on turns, a torn boot, or grease on the inside of the wheel.
Tip: Check the boots whenever the wheel is off.
See all CV Joint Parts - Front parts for the 2005 Jeep Liberty
The U-joint at the front end of the rear driveshaft, at the transfer case (4WD) or the transmission (2WD).
Signs of wear: A clunk when shifting into gear, or a vibration that grows with speed.
Tip: There are two joint sizes on these years, so match the caps and the yoke span to yours.
The U-joint where the rear driveshaft bolts to the pinion yoke of the rear axle.
Signs of wear: A squeak when rolling slowly, a clunk on take off, or a vibration.
Tip: Mark the shaft and the yoke before you separate them.
A stamped arm from a bracket under the axle tube forward to a bracket on the body. The rear sway bar is bolted to it.
Signs of wear: Clunks, a rear that steers itself, or rust through the arm.
Tip: Rear lower arms on many 2002 to 2007 Liberty were recalled for corrosion, so check the arm itself as well as the bushings.
A single A shaped arm whose tip holds a ball joint on top of the differential and whose two legs bolt to the body. It keeps the axle centred, so there is no track bar.
Signs of wear: A clunk from the rear over bumps or on take off, or a rear that shifts side to side.
Tip: The arm comes with the ball joint; the joint is also sold on its own.
The ball joint in the tip of the rear upper arm, on top of the differential.
Signs of wear: A clunk from the rear over bumps or on take off.
Tip: It presses into the arm.
See all Rear Upper Ball Joint parts for the 2005 Jeep Liberty
Rubber bushings in the two leg ends of the rear upper arm, at the body brackets.
Signs of wear: Clunks over bumps or on take off.
Tip: Polyurethane kits press into the original arm.
See all Rear Control Arm Bushings parts for the 2005 Jeep Liberty
Rubber bushings at the body end and the axle end of each rear lower arm. The axle end bushing is the slotted one.
Signs of wear: Clunks, or a rear that feels loose in turns.
Tip: The body end bushing changed for 2004, so 2002 and 2003 take different parts.
See all Rear Control Arm Bushings parts for the 2005 Jeep Liberty
The rear coil springs sit on pads on the axle tubes, on a rubber insulator, and up into pockets in the body.
Signs of wear: A sagging rear, or a broken coil.
Tip: Replace them in pairs.
A rubber bellows bumper inside each rear coil that stops the axle hitting the body.
Signs of wear: A bang from the rear over big bumps.
Tip: Check it whenever the springs are out.
A U shaped bar ahead of the rear axle whose legs are bolted to the two rear lower arms, so it twists when one side of the axle rises.
Signs of wear: Rear body roll, or a rattle from loose clamp bolts.
Tip: The bar comes off with the lower arms, so new arms need it bolted back on.
The rear shocks stand behind the axle, from a bracket under the tube up to the body behind the coil.
Signs of wear: Bouncing, a floaty rear, oil on the body, or cupped rear tires.
Tip: Keep the extended length within the factory figure so the springs stay seated.
The sealed hub bearing bolts to the knuckle with three bolts, and the wheel studs are in its flange.
Signs of wear: A hum or growl that changes with speed or in turns, or play in the wheel.
Tip: Left and right hubs differ on vehicles with four wheel ABS; non ABS 2002 to 2005 models take one hub for both sides.
See all Front Wheel Bearing and Hub Assembly parts for the 2005 Jeep Liberty
A 288 mm vented rotor over the hub.
Signs of wear: A pulsing pedal or a scored surface.
Tip: Replace them in pairs.
A single piston floating caliper on its bracket behind the rotor.
Signs of wear: Pulling to one side, a dragging brake or a leak.
Tip: Bleed the brakes after you fit it.
Pads either side of the front rotor, inside the caliper.
Signs of wear: Squeal from the wear indicator, grinding, or a longer stop.
Tip: Check the rotors when you change pads.
A 285 mm solid rotor. Its hat is the drum for the parking brake shoes.
Signs of wear: A pulsing pedal or a scored surface.
Tip: The 2002 and some 2003 models have rear drum brakes instead.
A single piston floating caliper behind the rear axle.
Signs of wear: A dragging brake, a leak or uneven pad wear.
Tip: Bleed the brakes after you fit it.
Pads either side of the rear rotor, inside the caliper.
Signs of wear: Squeal, grinding or a weak parking feel.
Tip: The 2007 Liberty takes a different pad set.
Small shoes inside the hat of the rear rotor that hold the vehicle when the parking brake is set.
Signs of wear: A parking brake that will not hold.
Tip: Adjust them before you fit the rotor.
Lower ball joints, outer tie rod ends, sway bar links and the strut fork bushings wear first. Check them with the front wheels off the ground: a worn joint shows up as play you can feel when you rock the wheel.
It presses into the bottom of the steering knuckle, and its stud points down into the lower control arm. The upper ball joint is part of the upper control arm, so the arm is replaced as an assembly.
No. A single A shaped upper arm with a ball joint on top of the differential keeps the axle centred, and two lower arms keep it square. A clunk from the rear often comes from the upper ball joint or the arm bushings.
The 2002 to 2007 Liberty uses this layout, but some parts changed: the lower ball joint for 2005, the inner tie rods for 2006, the rear lower arm bushings for 2004, the rear pads for 2007, and the rear brakes (drums on the 2002 and some 2003 models). The parts shown here are the ones listed for the 2005 Liberty.
Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.