2006 Jeep Liberty Suspension Diagram

This interactive diagram shows the front suspension, steering, driveline and rear suspension of the 2006 Jeep Liberty. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit, down to the side and position.

2006 Jeep Liberty 4WD Suspension Diagram (Full Chassis)

FRONT
The whole chassis from above the driver side. The front of the vehicle is to the left.

2006 Jeep Liberty 4WD Front Suspension and Steering Diagram

PASSENGER SIDEDRIVER SIDEFRONT
Front suspension and rack and pinion steering from above the front driver side corner.

2006 Jeep Liberty 4WD Rear Suspension Diagram

DRIVER SIDEPASSENGER SIDEREAR
Rear axle, its three links and the sway bar from above the rear driver side corner.

We carry parts for it Not stocked yet Hover or tap any part.

Kits and packages for your 2006 Jeep Liberty

3 kits

Packages

Complete Shock Package Kit
Includes
  • 2 × Front Strut (Coilover) (driver and passenger)
  • 2 × Rear Shock Absorber
$428.26
View package

Lift and leveling kits

See every part for the 2006 Jeep Liberty

The 2006 and 2007 Liberty has independent front suspension: a wide lower control arm and a forged upper control arm at each corner, with a coilover strut whose fork bolts to the lower arm, and rack and pinion steering ahead of the front wheels. The rear is a solid axle on coil springs, held by two lower arms and a single A shaped upper arm with a ball joint on top of the differential, with a sway bar bolted to the lower arms. The diagram is drawn from a four wheel drive model; the two wheel drive Liberty has no front differential or front CV axles.

We carry replacement parts for 34 of the 40 components on this diagram, 85 parts in all. See every part for the 2006 Jeep Liberty.

Questions about the 2006 Jeep Liberty suspension

What are the most common front end wear items on a 2006 Jeep Liberty?

Lower ball joints, outer tie rod ends, sway bar links and the strut fork bushings wear first. Check them with the front wheels off the ground: a worn joint shows up as play you can feel when you rock the wheel.

Where is the lower ball joint on a Liberty?

It presses into the bottom of the steering knuckle, and its stud points down into the lower control arm. The upper ball joint is part of the upper control arm, so the arm is replaced as an assembly.

Does the 2006 Liberty have a rear track bar?

No. A single A shaped upper arm with a ball joint on top of the differential keeps the axle centred, and two lower arms keep it square. A clunk from the rear often comes from the upper ball joint or the arm bushings.

Which U-joints fit the rear driveshaft on a 2006 Liberty 4x4?

The rear driveshaft has a U-joint at each end, and the diagram draws the 1310 size at both. At the rear axle the 1310 joint (Moog 369) is the one listed. At the front end, behind the transfer case, some 2006 Liberty 4x4 models take the larger 1330 joint (Moog 354, 444 or 254) instead, and the catalogs list both sizes there without saying which trucks get which. The 1330 is wider across its bearing caps (about 3-5/8 inch against 3-7/32 inch on the 1310), so measure the old joint before you order.

Which years share this suspension?

The 2006 and 2007 Liberty share this drawing. The parts shown are listed for both years, with two exceptions: the rear brake pads (ZD981 in 2006, ZD981A in 2007) and the steering rack mount bushing (listed for 2006, not for 2007). The inner tie rods are the 2006 to 2007 design.

Printable 2006 Jeep Liberty suspension diagrams

Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.

2006 Jeep Liberty 4WD Suspension Diagram (Full Chassis) with numbered parts
2006 Jeep Liberty 4WD Suspension Diagram (Full Chassis)
2006 Jeep Liberty 4WD Front Suspension and Steering Diagram with numbered parts
2006 Jeep Liberty 4WD Front Suspension and Steering Diagram
2006 Jeep Liberty 4WD Rear Suspension Diagram with numbered parts
2006 Jeep Liberty 4WD Rear Suspension Diagram