unarchive In The Box of 191831 keyboard_arrow_down
- Qty 2 of 60690 - 0.750 Top I.D. X 1.700 Bottom I.D. X 1.100 Height
lock Warranty Information keyboard_arrow_down
- Lifetime Warranty. Prothane guarantees all Prothane Suspension Parts to be free of defects in materials and workmanship (not due to abuse, neglect or misapplication) for the total time the vehicle remains with the original purchaser of the product(s). Should the products fail to meet these conditions, Prothane will replace the product, free of charge. This excludes any and all related labor charges. The product must be shipped to Prothane (postage prepaid) along with a copy of the original receipt."
Prothane Polyurethane Universal Dust Boots

Many of you are finding out that the rubber boot on your ball joint or tie rod has rotted away or has split. These boots are extremely important for the suspension of your vehicle. Fortunately, Prothane makes Universal Dust boots that will fit most vehicles. These dust boots are made of polyurethane and are far more durable than rubber. This will seal your boot to retain the grease in the joint, as well as protecting the joint from dirt, sand, water, and snow.
How-to obtain measurements
In order to select the proper boot, you will first need to grab a few measurements. The best way to do this is with a set of digital calipers. You will need to measure the diameter of the base where the boot will sit, the diameter of the shaft (also called the Pin Opening Diameter) and the height of the boot. Once you have gotten to your tie rod end measure these three spots. Be sure to be as exact as possible and to write down your measurements. If you have any trouble getting these measurements, give our customer service team at DST a call. It is important to note that you do not want to choose a boot that is bigger than your measurements. You want to choose a boot that is just slightly smaller than the measurements you obtained. The elasticity of the polyurethane will allow the hole to stretch and grip the joint tightly. If you choose a boot that is too large there will be a gap which lets in debris.


After Measureing Your Dust Boots
Now that you have these measurements, you can verify that this is the boot that you need. If you find that your measurements do not match this boot, go to our Universal Dust Boot page to match a part to your measurements.

Product Reviews for
- 5 Star (5)
-
-
- 83%
-
- 4 Star (0)
-
-
- 0%
-
- 3 Star (1)
-
-
- 17%
-
- 2 Star (0)
-
-
- 0%
-
- 1 Star (0)
-
-
- 0%
-
Prothane 191831
starstarstarstar_borderstar_border" Review 2 Years Later "
Two boots split within the first two months. Luckily I bought two extra. When I replaced the failed boots, I cut the replacement boot skirts shorter to reduce the amount of bulge and they have not failed.
verified_user Verified Buyer - Robert Grapengater - . Prothane 191831 - 3 out of 5starstarstarstarstar" Well made, nice product "
Fit correctly,
verified_user Verified Buyer - Jeffrey P. Kulbis - . Prothane 191831 - 5 out of 5starstarstarstarstar" Good quality boot. Should last a very very long time. "
I purchased this boot to fit the Moog DS1413 Track Bar for a 98 Ram 1500. I was a bit concerned that the size didnt match up when ordering and once it arrived, it slipped over with some stretch. Once installed it works perfectly fine. Note: I used a little ring of RTV on the base for grease control.
verified_user Verified Buyer - Michael Long - . Prothane 191831 - 5 out of 5starstarstarstarstar" Worked great "
Fit properly.
verified_user Verified Buyer - Dale Spires - . Prothane 191831 - 5 out of 5