Front End Steering Rebuild Kits
Package kits bundle the wearing steering parts and ball joints for this truck.
This interactive diagram shows the front suspension, steering, driveline and rear suspension of the 2004 Dodge Ram 2500 with two wheel drive. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit your truck, down to the side and position.
We carry parts for it Not stocked yet Hover or tap any part.
The two wheel drive Ram 2500 does not share the 4x4's solid front axle. It has an independent front suspension: an upper and a lower control arm on each side, a coil spring on the lower arm with the shock inside it, and rack and pinion steering. The rear is a solid axle on leaf springs.
We carry replacement parts for 29 of the 41 components on this diagram, 104 parts in all. See every part for the 2004 Dodge Ram 2500 2WD.
Package kits bundle the wearing steering parts and ball joints for this truck.
Front and rear shock sets for the whole truck.
Every U-joint for the truck in one order. Check the engine and driveshaft notes on each package.
Spacers on top of the front coil springs that raise the front to level the truck.
The upper ball joint is the top pivot of the steering knuckle. Its stud points down into the knuckle from the end of the upper control arm.
Signs of wear: A clunk over bumps, wandering, uneven tire wear, or play when the tire is rocked top to bottom with the front lifted.
Tip: On 2003 to 2005 trucks the upper joint is part of the aluminium upper arm, so the arm is replaced as one piece. From 2006 a press-in joint is sold on its own.
The lower ball joint presses into the outer end of the lower control arm. Its stud points up into the bottom of the steering knuckle and carries the truck's weight.
Signs of wear: A clunk or knock over bumps, a shimmy, or play at the bottom of the tire with the front lifted.
Tip: The lower joint is loaded by the coil spring, so the arm must be supported before the joint is separated.
See all Front Lower Ball Joint parts for the 2004 Dodge Ram 2500 2WD
An A-shaped arm on two bushings at a frame bracket above the spring pocket. Its outer end holds the upper ball joint.
Signs of wear: Clunks, torn or cracked bushings, or a worn ball joint at the outer end.
Tip: Trucks built through 2006 have a cast aluminium upper arm; 2007 and 2008 trucks have a stamped steel arm with a different part number.
See all Front Control Arm parts for the 2004 Dodge Ram 2500 2WD
A stamped steel A-arm on two bushings at the front crossmember. The coil spring and shock sit on a seat in the middle of it, and the lower ball joint is at its outer end.
Signs of wear: Clunks, a shimmy after bumps, torn bushings, or a worn lower ball joint.
Tip: Complete arms come with new bushings and ball joint. Support the arm before unbolting anything, because the coil spring is under load.
See all Front Control Arm parts for the 2004 Dodge Ram 2500 2WD
Rubber bushings in the two inner eyes of the upper arm, where it pivots on the frame bracket.
Signs of wear: Clunks over bumps, alignment that won't hold, or cracked rubber.
Tip: The bushing kit changed for 2006 trucks. Check the year on each listing.
See all Front Control Arm Bushings parts for the 2004 Dodge Ram 2500 2WD
Rubber bushings in the front and rear inner eyes of the lower arm, where it pivots on the crossmember.
Signs of wear: Clunks when braking or over bumps, or the tire moving fore and aft.
Tip: 2003 and 2004 trucks use different forward and rearward bushings. Check the position on each listing.
See all Front Control Arm Bushings parts for the 2004 Dodge Ram 2500 2WD
The cast knuckle (spindle) turns between the upper and lower ball joints. It carries the hub bearing, the brake caliper and the steering arm for the outer tie rod end.
Signs of wear: Rarely wears out. Replace it after damage, or if a tapered ball joint or tie rod hole is worn.
Each front coil sits on the lower control arm and pushes up into a spring pocket on the frame. The shock runs up through the middle of it.
Signs of wear: A sagging front, the truck leaning to one side, or a broken coil end.
Tip: The coil is under heavy load. Use a spring compressor, or support the lower arm with a jack, before separating the lower ball joint.
A thick rubber pad between the top of the coil and the frame spring pocket. It quiets the spring.
Signs of wear: A squeak or clunk from the spring over bumps, or a torn pad.
Tip: Replace it whenever the coil is out.
See all Front Coil Spring Isolator Pads parts for the 2004 Dodge Ram 2500 2WD
The front shock runs up through the coil spring. Its stem goes through the top of the spring pocket and its cross bar bolts to the lower control arm.
Signs of wear: Bouncing after bumps, nose dive under braking, or a leaking shock.
Tip: Leveling kits often need a spacer on the shock stem. Check the kit's notes.
See all Front Shock Absorber parts for the 2004 Dodge Ram 2500 2WD
A urethane stop on top of the lower control arm, between the ball joint and the coil spring. It strikes the frame above it at full compression.
Signs of wear: A harsh bang when the front bottoms out, or a missing or crumbled stop.
See all Front Bump Stops parts for the 2004 Dodge Ram 2500 2WD
The bar runs across the front of the truck under the frame and its arms reach back to links on the lower control arms.
Signs of wear: Body roll in turns. The bar itself rarely fails; listen for its bushings and links first.
Two rubber bushings in straps that hold the sway bar to the frame.
Signs of wear: Squeaks or clunks over bumps and in turns.
Tip: Bushings are sold by bar diameter. Measure the bar, or check the size in the listing.
See all Front Sway Bar Bushings parts for the 2004 Dodge Ram 2500 2WD
A vertical link from the end of each sway bar arm down to a tab on the lower control arm.
Signs of wear: Rattles or clunks over small bumps, or a broken link.
See all Front Sway Bar Endlinks parts for the 2004 Dodge Ram 2500 2WD
The inner tie rod screws onto the end of the steering rack inside the rubber boot. It carries the steering out to the outer tie rod end.
Signs of wear: Wandering, loose steering, or a clunk when turning the wheel back and forth. Check by squeezing the boot while someone turns the wheel.
Tip: Replace the boot at the same time, and set the toe with an alignment afterwards.
See all Front Inner Tie Rod End parts for the 2004 Dodge Ram 2500 2WD
The outer tie rod end threads onto the inner tie rod and its stud goes into the steering arm on the knuckle.
Signs of wear: Loose or wandering steering, uneven inner or outer tire wear, or a torn boot.
Tip: Count the turns when you remove it, so the toe stays close until the alignment.
See all Front Outer Tie Rod End parts for the 2004 Dodge Ram 2500 2WD
Rubber bushings in the two mounting ears of the rack and pinion, where it bolts to the crossmember.
Signs of wear: The steering wheel turns a little before the wheels respond, or a clunk when turning.
Tip: Only move the rack forward enough to press out the old bushings.
See all Steering Rack Bushings parts for the 2004 Dodge Ram 2500 2WD
The rear driveshaft. The three joint version is two pieces with a center support bearing; some trucks have a one piece, two joint shaft.
Signs of wear: Vibration on takeoff or at speed.
The front U-joint of the rear driveshaft, at the transmission.
Signs of wear: A clunk when shifting into gear, or vibration.
The middle U-joint, just behind the center support bearing, on trucks with the three joint shaft.
Not on every vehicle: Only on trucks with the two piece (three joint) rear driveshaft.
Signs of wear: Vibration that comes and goes with load.
The U-joint at the rear differential end of the rear driveshaft.
Signs of wear: A clunk on takeoff, a squeak, or rust dust around the caps.
Tip: Rear joints come in 1-3/16 in and 1-3/8 in cap sizes depending on engine and transmission. Check the fit notes.
Holds the middle of the two piece rear driveshaft to a crossmember.
Not on every vehicle: Only on trucks with the two piece (three joint) rear driveshaft (Moog driveline diagram B for the 2006 2WD truck). Trucks with the one piece shaft (diagram A) have no center bearing.
Signs of wear: A rumble or vibration at speed, or a torn rubber mount.
The solid rear axle. Diesel trucks use the AAM 11.5 in full floating axle drawn here; gas trucks typically use the 10.5 in axle.
Signs of wear: Leaks at the cover or axle seals, or gear whine.
A multi leaf spring each side, clamped on top of the axle with U-bolts. The front eye bolts to a fixed hanger and the rear eye to a shackle.
Signs of wear: A sagging rear, a broken leaf, or a spring that has shifted on the axle.
Bushings in the spring eyes at the front hanger and the rear shackle.
Signs of wear: Squeaks over bumps, clunks on takeoff, or rubber pushed out of the eye.
See all Rear Leaf Spring Bushings parts for the 2004 Dodge Ram 2500 2WD
The link at the rear of each spring that lets the spring grow longer as it flexes.
Signs of wear: Squeaks, a clunk, or a worn or cracked shackle.
Two U-bolts each side clamp the spring to the axle perch with a plate underneath.
Signs of wear: A spring that has shifted on the axle, or loose U-bolt nuts.
Tip: Gas and diesel trucks use different U-bolt sizes. Use new U-bolts when the spring is removed.
The rear shocks are staggered: one sits ahead of the axle and the other behind it.
Signs of wear: Bouncing, a rear that squats or floats, or leaks.
See all Rear Shock Absorber parts for the 2004 Dodge Ram 2500 2WD
A rubber stop on a bracket under each frame rail, above the leaf spring.
Signs of wear: A hard bang when loaded, or a torn or missing stop.
See all Rear Bump Stops parts for the 2004 Dodge Ram 2500 2WD
An aftermarket rear sway bar, clamped to the axle with links up to the frame rails. These trucks were not built with one.
Not on every vehicle: No factory rear sway bar is listed for the 2003 to 2008 Ram 2500. We list rear links for the 2004 truck only; if your truck has a bar, its links fit here.
Signs of wear: Body roll at the rear, or clunks from the links.
Tip: Not drawn: the factory truck has no rear bar. Look for links hanging from the frame rails behind the axle if one was added.
Links from each end of an added rear sway bar up to brackets on the frame rails.
Not on every vehicle: No factory rear sway bar is listed for the 2003 to 2008 Ram 2500. We list rear links for the 2004 truck only; if your truck has a bar, its links fit here.
Signs of wear: Rattles over small bumps, or a broken link.
Tip: Not drawn.
See all Rear Sway Bar Endlinks parts for the 2004 Dodge Ram 2500 2WD
Bushings that clamp an added rear sway bar to the axle.
Not on every vehicle: No factory rear sway bar is listed for the 2003 to 2008 Ram 2500. We list rear links for the 2004 truck only; if your truck has a bar, its links fit here.
Signs of wear: Clunks or squeaks from the rear over bumps.
Tip: Not drawn.
A sealed bearing and hub unit bolted to the knuckle with three bolts, with eight wheel studs and the ABS sensor lead.
Signs of wear: A hum or growl that changes with speed, play in the wheel, or an ABS light.
Tip: 2003 to 2005 trucks and 2006 to 2008 trucks take different hub units. Check the year on the listing.
See all Front Wheel Bearing and Hub Assembly parts for the 2004 Dodge Ram 2500 2WD
A vented 353 mm rotor that slips over the hub studs.
Signs of wear: A pulsing pedal, grooves or rust ridges, or thickness under the minimum.
See all Front Brake Rotor parts for the 2004 Dodge Ram 2500 2WD
The caliper sits at the back of each front rotor and squeezes the pads with its pistons.
Signs of wear: Pulling while braking, a dragging wheel, leaks, or uneven pad wear.
See all Front Brake Caliper parts for the 2004 Dodge Ram 2500 2WD
One pad each side of the rotor, held in the caliper.
Signs of wear: Squealing, grinding, or a long pedal.
See all Front Brake Pads parts for the 2004 Dodge Ram 2500 2WD
A 352 mm rear rotor. The inside of its hat is the drum for the parking brake shoes.
Signs of wear: A pulsing pedal or worn friction faces.
See all Rear Brake Rotor parts for the 2004 Dodge Ram 2500 2WD
The caliper sits behind each rear rotor, toward the bottom.
Signs of wear: Pulling, a dragging wheel, or leaks.
See all Rear Brake Caliper parts for the 2004 Dodge Ram 2500 2WD
One pad each side of the rear rotor.
Signs of wear: Squealing, grinding, or low pad material.
See all Rear Brake Pads parts for the 2004 Dodge Ram 2500 2WD
Small brake shoes inside the rear rotor hat. They hold the truck when the parking brake is set.
Signs of wear: A parking brake that will not hold the truck on a slope.
Tip: 2003 to 2005 trucks and 2006 to 2008 trucks take different shoes. Check the year on the listing.
See all Parking Brake Shoes parts for the 2004 Dodge Ram 2500 2WD
Rubber mounts between the frame and the cab and bed: a core support mount ahead of the front wheels, cab mounts and bed mounts. The count changes with cab and bed length.
Signs of wear: Clunks from under the cab, a cab that shifts on the frame, or crushed or cracked rubber.
Tip: Body lift kits replace or space these mounts.
See all Body Mount Bushings Kit parts for the 2004 Dodge Ram 2500 2WD
No. The 4x4 has a solid front axle with a track bar and a steering box, while the two wheel drive truck has upper and lower control arms on each side and rack and pinion steering. Ball joints, control arms, tie rods and sway bar links are all different. The brakes and the rear suspension parts are shared.
On 2003 to 2005 trucks the upper ball joint comes with the aluminium upper control arm, so the arm is replaced as an assembly. The lower ball joint presses into the lower arm and is sold on its own.
Common causes are worn lower ball joints, control arm bushings, sway bar links and inner tie rods. With the front lifted, check for play at the top and bottom of each tire, and squeeze the rack boots while someone turns the wheel to feel for a loose inner tie rod.
Yes. Replacing tie rods, ball joints or control arms changes the alignment. Count the turns when you remove an outer tie rod end so the toe stays close until the truck is aligned.
The 2003 to 2008 Ram 2500 2WD has the same layout. Some parts change by year: the hub, the control arm bushings and the parking brake shoes changed for 2006, and the upper control arm changed from aluminium to steel for 2007. The parts shown here are the ones listed for the 2004 truck.
Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.