Complete Strut Assemblies
A strut with its spring, mount and boot already assembled, so no spring compressor is needed.
This interactive diagram shows the front suspension, steering, 4WD driveline and rear suspension of the 2017 Ford Explorer 4WD. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit your Explorer, down to the side and position.
We carry parts for it Not stocked yet Hover or tap any part.
The 2011 to 2019 Explorer uses MacPherson struts at the front, bolted to the knuckles by a two bolt clevis, with a forged L shaped lower arm under each corner. The steering rack sits behind the front axle and the front sway bar runs across the top of the cradle with long links up to the struts. The rear is a multi-link design on its own subframe: a wide spring arm behind the axle carries the coil spring, an A shaped upper arm sits on top, a toe link and a short trailing link sit ahead of the axle, and the shock is separate from the spring. On 4WD models a power transfer unit on the transaxle drives a two piece driveshaft to the rear drive unit.
We carry replacement parts for 30 of the 40 components on this diagram, 91 parts in all. See every part for the 2017 Ford Explorer 4WD.
A strut with its spring, mount and boot already assembled, so no spring compressor is needed.
Front struts and rear shocks for the whole truck in one order.
Cam bolts replace the two strut to knuckle bolts so front camber can be set.
Cam bolts for adjusting rear camber.
Package kits bundle the wearing front end parts in one order.
The strut is the front shock absorber and the upper locating part of the corner in one. A two bolt clevis at its bottom clamps the top of the knuckle, the coil spring sits on it, and its top bolts into the strut tower.
Signs of wear: Bouncing after bumps, nose dive under braking, fluid on the tube, or a knock from the top of the strut over rough roads.
Tip: Struts are sold bare or as a complete assembly with the spring and mount fitted. 2011 to 2013 trucks and 2013 to 2019 trucks take different struts, so check the build date.
See all Front Shock Absorber parts for the 2017 Ford Explorer 4WD
The front coil spring sits on a seat on the strut tube, with a rubber isolator under it, and pushes up against the top mount. It carries the weight of the front of the vehicle.
Signs of wear: A front corner sitting lower than the other, a broken coil end, or a clunk when turning the wheel at a stop.
Tip: Replace springs in pairs, and fit new isolators at the same time.
See all Front Coil Springs parts for the 2017 Ford Explorer 4WD
The strut mount is the rubber and bearing block at the top of the strut. Three studs hold it to the strut tower, and its bearing lets the strut turn with the steering.
Signs of wear: Clunks or creaks from the top of the strut when steering at low speed, or a steering wheel that is slow to return to center.
Tip: The mount is usually replaced with the strut, since the strut has to come out either way.
See all Front Strut Mount parts for the 2017 Ford Explorer 4WD
A rubber bellows covers the strut rod to keep grit off its seal, and the bump stop inside it cushions the strut at full compression. The spring hides it in the assembled view; the exploded view shows it.
Signs of wear: A torn boot, a rusty or scored strut rod, or a hard bang over big bumps.
Tip: Fit a new boot and bump stop whenever the strut is replaced.
A forged L shaped arm. The ball joint pressed into its outer end carries the knuckle, a short leg runs in to a bushing at the side of the cradle, and a long rear leg ends in a large bushing held in an aluminum housing that bolts up under the cradle.
Signs of wear: Clunks over bumps, steering that wanders under braking, cracked bushings, or play in the ball joint.
Tip: Left and right arms are different parts. The ball joint is not sold on its own for this truck, so a worn joint means a new arm.
See all Front Control Arm parts for the 2017 Ford Explorer 4WD
Each lower arm has two bushings: a small one in the front leg, on a bolt that runs front to back, and a large rear one inside an aluminum housing bolted to the cradle.
Signs of wear: Clunks when braking or pulling away, a vague steering feel, or rubber that is cracked or pushed out of its housing.
Tip: The rear bushings come with their housing and are listed by side.
See all Front Control Arm Bushings parts for the 2017 Ford Explorer 4WD
The knuckle carries the hub and the brake caliper. The strut clevis clamps its top, the ball joint stud sits in its bottom, and its rear arm takes the outer tie rod end.
Signs of wear: Knuckles rarely wear out. A bent knuckle after a curb strike shows as a pull or a crooked steering wheel that an alignment will not fix.
Tip: The hub bolts to the knuckle with four bolts, so it can be changed without pressing.
The 32 mm front sway bar runs across the top of the rear of the front cradle. Long links join its ends to brackets on the struts, so it twists when one side moves more than the other and keeps the truck flatter in turns.
Signs of wear: Body roll that feels worse than it used to, usually from worn links or bushings rather than the bar.
Tip: Bushings fit one bar size. The stock front bar is 32 mm.
Two rubber bushings in steel clamps hold the front bar to the cradle.
Signs of wear: Squeaks or knocks from the front over speed bumps, or a bar that moves in its clamps.
Tip: The 2011 and 2012 trucks list a different bushing kit from 2013 to 2019.
See all Front Sway Bar Bushings parts for the 2017 Ford Explorer 4WD
A long link with a ball stud at each end. The top bolts to a bracket on the strut tube and the bottom to the end of the sway bar.
Signs of wear: A rattle or knock from the front over small bumps, or a link that moves by hand.
Tip: Left and right links are listed separately. Replace them in pairs.
See all Front Sway Bar Endlinks parts for the 2017 Ford Explorer 4WD
An electrically assisted rack and pinion sits behind the front axle under the rear edge of the cradle. Rubber boots seal each end over the inner tie rods.
Signs of wear: A torn boot, a clunk through the steering wheel, or a steering assist warning on the dash.
Tip: Replace a torn boot early. Grit inside it wears out the inner tie rod and the rack seals.
The inner tie rod screws into the end of the rack inside the boot. Its ball joint lets the rod swing as the suspension moves.
Signs of wear: Loose or wandering steering, uneven tire wear, or a clunk when turning.
Tip: 2017 to 2019 trucks can take a different inner tie rod from earlier years. Always set the toe after replacing tie rods.
See all Front Inner Tie Rod End parts for the 2017 Ford Explorer 4WD
The outer tie rod end threads onto the inner rod and its stud points up through the steering arm at the back of the knuckle.
Signs of wear: Play in the steering, a clunk over bumps when turning, or feathered wear on the tire edges.
Tip: Count the turns when removing the old end so the new one goes on close to the old toe setting, then align.
See all Front Outer Tie Rod End parts for the 2017 Ford Explorer 4WD
A half shaft drives each front wheel. The driver side shaft comes from the transaxle and the passenger side shaft from the power transfer unit.
Signs of wear: Clicking when turning under power, grease thrown inside the wheel, or a split boot.
Tip: Replace the axle nut whenever the axle comes out.
See all CV Joint Parts - Front parts for the 2017 Ford Explorer 4WD
The power transfer unit bolts to the passenger side of the transaxle. It drives the passenger front axle and turns power back toward the rear through the driveshaft.
Signs of wear: A burnt oil smell, a leak at the right side of the transaxle, or a whine that changes with speed.
Tip: Its fluid is separate from the transmission fluid and is often overlooked.
A two piece driveshaft with a center support runs under the floor from the power transfer unit to the rear drive unit.
Signs of wear: A vibration that rises with speed, or a clunk when pulling away.
Tip: The center support bearing is a common wear point on high mileage trucks.
The rear drive unit sits in the middle of the rear subframe. It takes power from the driveshaft and sends it out through two rear halfshafts.
Signs of wear: A whine or howl from the rear, or a leak at its seals.
Tip: Use the fluid type on the unit's tag when topping up.
A halfshaft runs from each side of the rear drive unit to the rear hub, between the toe link and the spring arm.
Signs of wear: Clicking or clunking from the rear under power, or grease from a split boot.
Tip: The rear axle nut is replaced along with the shaft.
The cast rear knuckle carries the hub and caliper and ties every rear link together: the upper arm on top, the spring arm at the bottom, the toe link and trailing link at the front, and the shock and bar link.
Signs of wear: Rear toe that will not stay in alignment, a clunk from the rear, or a seized toe link ball joint.
Tip: Ford recalls covered the toe link ball joint in this knuckle; complete knuckle assemblies come with new bushings and the ball joint.
A large bushing pressed into the top of the knuckle, where the upper arm's clevis bolts on.
Signs of wear: A clunk from the rear over bumps, or rear camber that has crept out.
Tip: Ford warns that some aftermarket knuckle bushings have led to toe link failures; many shops replace the whole knuckle instead.
See all Rear Control Arm Bushings parts for the 2017 Ford Explorer 4WD
A bushing pressed into the back of the rear knuckle. The shock's lower clevis bolts through it.
Not on every vehicle: Sold separately for 2011 to 2015 trucks; later trucks get it with the knuckle assembly.
Signs of wear: A knock from the rear over bumps, or a shock bolt that has worked loose.
Tip: Listed for 2011 to 2015 trucks only; on later trucks the bushing is serviced with the knuckle.
A wide stamped arm behind the axle. Its inner bushing pivots on the rear of the subframe, the coil spring sits in a pocket on top, and a clevis at its outer end bolts to the bottom of the knuckle.
Signs of wear: Clunks from the rear, a sagging corner, or rust through the spring pocket.
Tip: The same arm fits both sides.
See all Rear Control Arm parts for the 2017 Ford Explorer 4WD
The bushing in the inner end of the spring arm, on a bolt that runs front to back through the subframe.
Signs of wear: A thump from the rear over bumps or a vague rear end in turns.
Tip: The arm must be at ride height before the bolt is tightened.
See all Rear Control Arm Bushings parts for the 2017 Ford Explorer 4WD
The rear coil spring stands on the spring arm's pocket and pushes up against a seat in the body. The shock is separate.
Signs of wear: A rear corner sitting low, a broken end coil, or a clunk over bumps.
Tip: Support the spring arm before undoing its outer bolt; the spring is under load.
An A shaped arm on top of the rear corner. Two inner bushings mount it to the subframe and a clevis at its outer end bolts through the knuckle's upper bushing.
Signs of wear: Uneven inner tire wear, a clunk from the rear, or cracked bushings.
Tip: Left and right arms are different parts.
See all Rear Control Arm parts for the 2017 Ford Explorer 4WD
The upper arm's two inner bushings: a small one at the front and a larger one in an aluminum housing at the rear.
Signs of wear: Creaks or clunks from the rear, or rear camber that will not stay set.
Tip: Greasable and non greasable rear bushings are both listed.
See all Rear Control Arm Bushings parts for the 2017 Ford Explorer 4WD
A lateral link ahead of the axle with a turnbuckle for setting rear toe. A bushing at its inner end mounts it to the subframe, and a fork at its outer end bolts through a ball joint in the knuckle.
Signs of wear: Rear tires wearing on their edges, a vague rear end, or a bent or cracked link.
Tip: Ford recalled these links on many 2011 to 2019 trucks; check for open recalls before buying. Set rear toe after fitting.
See all Rear Control Arm parts for the 2017 Ford Explorer 4WD
A short rod from the knuckle's lower front leg forward and inboard to a bushing in the subframe. It holds the knuckle against fore and aft loads.
Signs of wear: A clunk from the rear under braking or acceleration, or a torn bushing.
Tip: The same link fits both sides.
See all Rear Control Arm parts for the 2017 Ford Explorer 4WD
The rear shock stands just behind the axle, separate from the spring. Its lower clevis bolts through a bushing in the knuckle and its top stud bolts into the body.
Signs of wear: A bouncy or floaty rear end, oil on the shock body, or a knock over bumps.
Tip: Replace shocks in pairs. The top nuts are reached from inside the cargo area trim on many trucks.
See all Rear Shock Absorber parts for the 2017 Ford Explorer 4WD
The rear bar runs across the subframe ahead of the axle in two clamps, and short links join its ends to the knuckles.
Signs of wear: More body roll than usual, or a knock from the rear over bumps (usually the links or bushings).
Tip: Thicker aftermarket rear bars are sold for this truck.
Two rubber bushings in clamps hold the rear bar to the subframe.
Signs of wear: Squeaks or knocks from the rear over speed bumps.
Tip: Bushings fit one bar size only.
See all Rear Sway Bar Bushings parts for the 2017 Ford Explorer 4WD
A short link with a ball stud at each end, from the end of the rear bar up to a tab on the knuckle.
Signs of wear: A rattle from the rear over small bumps.
Tip: Left and right links are listed separately.
See all Rear Sway Bar Endlinks parts for the 2017 Ford Explorer 4WD
A sealed bearing and hub unit bolts to the knuckle with four bolts. The wheel studs are pressed into its flange and the half shaft runs through its splined center.
Signs of wear: A hum or growl that changes with speed and gets louder in turns, or play in the wheel.
Tip: 2011 and 2012 trucks and 2013 to 2019 trucks list different front hubs.
See all Front Wheel Bearing and Hub Assembly parts for the 2017 Ford Explorer 4WD
A vented rotor turns with the hub. The drawing shows the 352 mm rotor of the XLT and up; base trucks use a 325 mm rotor.
Signs of wear: Pulsing in the brake pedal, grooves or a lip on the rotor face, or squealing under braking.
Tip: Check the rotor size before ordering. 2013 and later trucks can have either size.
See all Front Brake Rotor parts for the 2017 Ford Explorer 4WD
A two piston floating caliper sits ahead of the axle on a bracket bolted to the knuckle.
Signs of wear: A pull to one side under braking, uneven pad wear, or a sticking or leaking piston.
Tip: Heavy duty brake trucks use a different caliper.
See all Front Brake Caliper parts for the 2017 Ford Explorer 4WD
Two pads in the caliper squeeze the rotor. The exploded view shows them out of the caliper.
Signs of wear: Squealing from the wear tab, grinding, or a longer stop than usual.
Tip: Standard and heavy duty brakes take different pads.
See all Front Brake Pads parts for the 2017 Ford Explorer 4WD
The rear bearing and hub bolts to the rear knuckle with four bolts. On 4WD trucks the halfshaft runs through its splined center.
Signs of wear: A hum from the rear that changes with speed, or play in the wheel.
Tip: The rear axle nut is replaced whenever the hub comes off.
See all Rear Wheel Bearing and Hub Assembly parts for the 2017 Ford Explorer 4WD
The rear rotor turns with the hub. The drawing shows the 345 mm rotor of the XLT and up; base trucks use a 330 mm rotor.
Signs of wear: A pulsing pedal, scoring, or a rusty lip on the rotor edge.
Tip: Release the parking brake before pulling the rotor.
See all Rear Brake Rotor parts for the 2017 Ford Explorer 4WD
A single piston caliper with the parking brake built in sits behind the rear axle.
Signs of wear: A dragging rear brake, a weak parking brake, or uneven rear pad wear.
Tip: The piston screws back in; a piston tool is needed when fitting new pads.
See all Rear Brake Caliper parts for the 2017 Ford Explorer 4WD
Two pads in the rear caliper squeeze the rear rotor.
Signs of wear: Squealing, grinding, or a parking brake that needs more lever travel.
Tip: Rear pads changed part numbers over the generation, so check the year.
See all Rear Brake Pads parts for the 2017 Ford Explorer 4WD
Front lower control arm rear bushings, front and rear sway bar links, inner and outer tie rod ends and the rear toe links are the parts most often replaced. Ford also recalled the rear toe links on many 2011 to 2019 Explorers, so check for open recalls.
No. The front uses struts, so the strut locates the top of the knuckle. There is one lower control arm per side, with the ball joint pressed into it. The rear does have an upper arm on each side.
Not for this truck. The front lower ball joint is pressed into the control arm, so a worn joint is fixed by replacing the arm, which comes with new bushings.
The arms, links, struts and knuckles are shared. 4WD models add the power transfer unit, a driveshaft, a rear drive unit and rear halfshafts, and the rear hubs carry the halfshafts.
The suspension arms, links and knuckles carried over. Brake sizes depend on the trim rather than the year: XLT and up trucks use 352 mm front and 345 mm rear rotors, and base trucks smaller ones. 2017 to 2019 trucks can take a different inner tie rod.
Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.