Complete Front Coil Over Assemblies
A front damper with its spring, mount and boot already assembled, so no spring compressor is needed.
This interactive diagram shows the front suspension, steering, axles and rear suspension of the 2004 Honda Accord Sedan. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit your car, down to the side.
We carry parts for it Not stocked yet Hover or tap any part.
The 2003 to 2007 Accord uses double wishbones at both ends. Up front, a cast lower arm and a stamped upper arm hold a tall knuckle, and the coil over damper stands on a fork that straddles the axle. The rear has five links per side: a trailing link, two lower arms, an upper arm with a ball joint and a short upper rear arm, with the coil over damper on the knuckle.
We carry replacement parts for 44 of the 50 components on this diagram, 212 parts in all. See every part for the 2004 Honda Accord Sedan.
A front damper with its spring, mount and boot already assembled, so no spring compressor is needed.
A rear damper with its spring and mount already assembled.
Front and rear dampers for the whole car in one order.
The wearing front end parts in one order.
One kit with the suspension bushings for the car or the front end.
All five adjustable rear arms for one car, for full camber, toe and setback adjustment.
A stamped A shaped arm high in the wheel well, above the tire. Its two bushings bolt to the inner wheel house and its ball joint sits on top of the tall knuckle upright. The coil over damper passes up between its legs.
Signs of wear: Clunks over bumps, uneven inner tire wear, or a torn ball joint boot.
Tip: Left and right arms are different parts, and most come with the ball joint and bushings already fitted.
See all Front Control Arm parts for the 2004 Honda Accord Sedan
Two rubber bushings at the inner ends of the upper arm, on bolts that run front to back through brackets on the wheel house.
Signs of wear: A knock over bumps from high in the wheel well, or rubber that is cracked or pushed out.
Tip: Offset upper bushings are made to add a little camber or caster on lowered cars.
See all Front Control Arm Bushings parts for the 2004 Honda Accord Sedan
The upper ball joint sits in the tip of the upper arm. Its stud points down into the top of the knuckle upright.
Signs of wear: A clunk over bumps, play when the wheel is rocked top to bottom, or a split boot.
Tip: Adjustable upper joints give a degree or more of camber change.
See all Front Upper Ball Joint parts for the 2004 Honda Accord Sedan
A cast A shaped arm. Its outer end carries the lower ball joint stud, a front leg pivots on a bushing on the subframe, and a rear leg ends in the large compliance bushing. The damper fork and the sway bar link bolt to it beside the ball joint.
Signs of wear: Clunks over bumps or when braking, a vague steering feel, or cracked bushings.
Tip: Left and right arms are different parts. Replacement arms usually come with new bushings.
See all Front Control Arm parts for the 2004 Honda Accord Sedan
The small bushing in the front leg of the lower arm, on a bolt that runs front to back through the subframe.
Signs of wear: A clunk when pulling away or braking, or rubber that is torn.
Tip: Offset front bushings are made to add caster.
See all Front Control Arm Bushings parts for the 2004 Honda Accord Sedan
The large rear bushing of the lower arm, called the compliance bushing. It lets the wheel move back slightly over bumps to soften the ride.
Signs of wear: Shimmy or a shake under braking, a clunk over bumps, or rubber that has split and leaked its fluid.
Tip: This is the most common wear item on the front of this car.
See all Front Control Arm Bushings parts for the 2004 Honda Accord Sedan
The bushing pressed into the lower arm beside the ball joint. The bottom of the damper fork bolts through it.
Signs of wear: A clunk from low in the corner over bumps, or a fork that moves on its bolt.
Tip: Press the bushing out of the arm with a bushing tool; the arm can stay on the car.
See all Front Control Arm Bushings parts for the 2004 Honda Accord Sedan
A forged fork that straddles the CV axle. Its top clamps the foot of the coil over damper and its bottom bolts to the lower arm.
Signs of wear: A bent fork after a curb strike pulls the wheel out of line.
Tip: The fork is reused when the damper is replaced.
The damper stands on the fork and runs up between the upper arm legs to the tower. The coil spring sits on it, so it works like a strut but the arms, not the damper, locate the wheel.
Signs of wear: Bouncing after bumps, nose dive under braking, or fluid on the body.
Tip: Complete assemblies with the spring and mount fitted need no spring compressor.
The front coil spring sits on a seat on the damper body and pushes up against the top mount, with rubber insulators at each end.
Signs of wear: A corner sitting low, a broken coil end, or a clunk when turning at low speed.
Tip: Replace springs in pairs.
See all Front Coil Springs parts for the 2004 Honda Accord Sedan
The rubber mount at the top of the damper. Three studs hold it to the tower.
Signs of wear: Knocks from the top of the damper over bumps.
Tip: Often replaced with the damper, since the damper must come out either way.
See all Front Strut Mount parts for the 2004 Honda Accord Sedan
A rubber bellows over the damper rod with the bump stop inside. The spring hides it in the assembled view; the exploded view shows it.
Signs of wear: A torn boot, a scored rod, or a hard bang over big bumps.
Tip: Fit a new boot whenever the damper is replaced.
See all Front Shock Bellows Boot Kit parts for the 2004 Honda Accord Sedan
The knuckle carries the hub bearing and the caliper. A tall upright rises from it over the tire to the upper ball joint, the lower ball joint is pressed into its bottom, and its rear arm takes the tie rod end.
Signs of wear: Knuckles rarely wear out. A bent one after a curb strike shows as a pull that an alignment will not fix.
Tip: Complete knuckle assemblies come with the bearing, hub and lower ball joint already fitted.
See all Front Lowering Spindles parts for the 2004 Honda Accord Sedan
The lower ball joint is pressed into the bottom of the knuckle. Its stud points down through the end of the lower arm and is held by a castle nut.
Signs of wear: A clunk over bumps or play when the wheel is rocked top to bottom.
Tip: It presses out of the knuckle with a ball joint press, or comes fitted in a complete knuckle.
See all Front Lower Ball Joint parts for the 2004 Honda Accord Sedan
The 25.4 mm front bar runs across behind the steering rack, held to the subframe by two bushings. Short links join its ends to the lower arms.
Signs of wear: More body roll than before, usually from worn links or bushings rather than the bar.
Tip: Check the bar diameter before ordering bushings.
Two rubber bushings in steel clamps hold the front bar to the subframe.
Signs of wear: Squeaks or knocks over speed bumps.
Tip: Bushings fit one bar diameter only.
See all Front Sway Bar Bushings parts for the 2004 Honda Accord Sedan
A short link, about 80 mm, with a ball stud at each end. The top bolts to a tab on the lower arm behind the damper fork and the bottom to the bar end.
Signs of wear: A rattle or knock over small bumps.
Tip: Left and right links are different parts on most listings, and early 2003 cars built in Japan use their own links. Check the fit notes.
See all Front Sway Bar Endlinks parts for the 2004 Honda Accord Sedan
Rubber mounts where the front subframe bolts to the body, behind the bumper and behind the lower arms. The subframe itself is shown with the frame and wheels.
Signs of wear: A clunk on hard acceleration or braking, or a subframe that has shifted.
Tip: Polyurethane mounts firm up the front end but pass more noise.
See all Front Subframe Bushings parts for the 2004 Honda Accord Sedan
The outer tie rod end threads onto the inner rod and its stud points up through the steering arm at the rear of the knuckle.
Signs of wear: Loose steering, wander, or uneven tire wear.
Tip: Count the turns when you remove it and get an alignment afterward.
See all Front Outer Tie Rod End parts for the 2004 Honda Accord Sedan
The inner tie rod screws into the end of the steering rack inside the rack boot.
Signs of wear: A clunk felt in the wheel or play at the rack end with the boot pulled back.
Tip: Four cylinder and V6 cars use different inner tie rods. Check the engine on the fit notes.
See all Front Inner Tie Rod End parts for the 2004 Honda Accord Sedan
Rubber boots seal each end of the rack around the inner tie rods.
Signs of wear: A split boot lets dirt into the rack.
Tip: Replace a torn boot before the inner tie rod wears.
See all Steering Rack Bellow parts for the 2004 Honda Accord Sedan
The power rack and pinion sits behind the front axle on the subframe, with the pinion on the driver side.
Signs of wear: Fluid leaks, a heavy wheel, or a knock over bumps.
Tip: Replace the rack boots whenever they split.
Two clamps with rubber bushings hold the rack to the subframe.
Signs of wear: A clunk felt through the wheel when turning, or a rack that shifts.
Tip: Firmer bushings sharpen the steering feel.
See all Steering Rack Bushings parts for the 2004 Honda Accord Sedan
The CV axles run from the transaxle to the hubs. The passenger side runs through an intermediate shaft with a carrier bearing behind the engine.
Signs of wear: A click when turning, grease thrown around the wheel, or a vibration under power.
Tip: Axles differ by transmission and engine; check the fit notes.
See all CV Joint Parts - Front parts for the 2004 Honda Accord Sedan
The upper arm runs out from the body to a ball joint on top of the rear knuckle. It sets the rear camber.
Signs of wear: Inner edge wear on the rear tires, or a knock from the rear over bumps.
Tip: Adjustable arms are made for lowered cars that need camber correction.
See all Rear Control Arm parts for the 2004 Honda Accord Sedan
A short link behind the upper arm, from the body to the top of the knuckle. With the trailing link it holds the wheel's fore and aft position.
Signs of wear: Worn bushings show as a knock over bumps.
Tip: Adjustable versions set the rear wheel's setback.
See all Rear Control Arm parts for the 2004 Honda Accord Sedan
A straight arm from the front cross member of the rear subframe out to the knuckle below the hub.
Signs of wear: Clunks from the rear, or uneven rear tire wear.
Tip: Arms sold as a pair or set cover this and the toe arm.
See all Rear Control Arm parts for the 2004 Honda Accord Sedan
The rearmost lower arm, from the rear cross member of the subframe to the back of the knuckle. A cam bolt at its inner end sets the rear toe.
Signs of wear: Rear tires wearing on one edge, or a rear end that steps out over bumps.
Tip: The inner bolt often seizes; plan to cut it out and fit a new cam bolt.
See all Rear Control Arm parts for the 2004 Honda Accord Sedan
A long link that runs forward and inboard from the front of the knuckle to a bracket on the body. The parking brake cable clips to it.
Signs of wear: A clunk on braking or pulling away, or a worn front bushing.
Tip: Left and right links are different parts.
The bushing in the front end of the trailing link, where it bolts to the body bracket.
Signs of wear: A clunk from the rear when braking.
Tip: It presses out of the link.
See all Trailing Arm Bushings parts for the 2004 Honda Accord Sedan
The rubber bushings in the ends of the rear arms, at the subframe, the body and the knuckle.
Signs of wear: Knocks from the rear and rear tire wear.
Tip: Offset bushings are made to adjust camber or toe.
See all Rear Control Arm Bushings parts for the 2004 Honda Accord Sedan
The rear knuckle holds the hub and the brake. All five rear arms, the damper and the sway bar link bracket attach to it.
Signs of wear: Rarely replaced unless bent in a crash.
The rear damper carries the coil spring. Its lower eye bolts to the knuckle and its top bolts up into the body behind the rear seat.
Signs of wear: Bouncing over bumps, a rear end that floats, or fluid on the body.
Tip: Complete assemblies with the spring and mount fitted need no spring compressor.
See all Rear Shock Absorber parts for the 2004 Honda Accord Sedan
The rear spring sits on the damper between a lower seat and the top mount, with rubber insulators.
Signs of wear: A sagging rear corner or a broken coil.
Tip: Replace in pairs.
See all Rear Coil Springs parts for the 2004 Honda Accord Sedan
The rubber mount at the top of the rear damper.
Signs of wear: A knock from the rear shelf over bumps.
Tip: Mount kits include the bushings and washers.
See all Rear Strut Mount parts for the 2004 Honda Accord Sedan
The bellows and bump stop on the rear damper rod.
Signs of wear: A torn boot or a hard bang over big bumps.
See all Rear Shock Bellows Boot parts for the 2004 Honda Accord Sedan
The rear bar runs across the rear cross member of the subframe and its ends reach forward to links on the knuckles. It is 14 mm on 4 cylinder cars and 13 mm on the V6.
Signs of wear: More rear body roll than before, usually from worn links or bushings.
Tip: Larger aftermarket bars bolt to the same mounts.
Two bushings in clamps hold the rear bar to the subframe.
Signs of wear: Squeaks or knocks from the rear.
Tip: Bushings fit one bar diameter only.
See all Rear Sway Bar Bushings parts for the 2004 Honda Accord Sedan
A link from the bar end up to a bracket bolted to the knuckle.
Signs of wear: A rattle from the rear over small bumps.
Tip: Left and right links are listed separately.
See all Rear Sway Bar Endlinks parts for the 2004 Honda Accord Sedan
The bearing is pressed into the knuckle and the hub is pressed through it. The CV axle splines into the hub and an axle nut holds it.
Signs of wear: A hum or growl that changes with speed and gets louder in turns.
Tip: Pressing a bearing needs a press; a complete knuckle assembly avoids that.
See all Front Wheel Bearing Assembly parts for the 2004 Honda Accord Sedan
A bolt on hub and bearing unit on the rear knuckle, held by an axle nut.
Signs of wear: A hum from the rear that changes with speed.
Tip: The Hybrid uses its own rear hub.
See all Rear Wheel Bearing and Hub Assembly parts for the 2004 Honda Accord Sedan
Vented front rotors, 282 mm on 4 cylinder cars and 300 mm on the V6.
Signs of wear: Pulsing in the pedal, grooves, or a lip at the edge.
Tip: Check the rotor size before ordering.
See all Front Brake Rotor parts for the 2004 Honda Accord Sedan
A single piston floating caliper ahead of the axle, on a bracket bolted to the knuckle.
Signs of wear: Pulling under braking, a dragging wheel, or a fluid leak.
Tip: Calipers are listed by side and by rotor size.
See all Front Brake Caliper parts for the 2004 Honda Accord Sedan
The pads sit in the caliper bracket either side of the rotor.
Signs of wear: Squealing, grinding, or a long pedal.
Tip: Pads differ for 282 mm and 300 mm rotors.
See all Front Brake Pads parts for the 2004 Honda Accord Sedan
Solid rear rotors on cars with rear discs: 260 mm, or 282 mm on the 2005 to 2007 V6 and Hybrid.
Signs of wear: Pulsing or noise from the rear.
Tip: Cars with rear drums use drums and shoes instead.
See all Rear Brake Rotor parts for the 2004 Honda Accord Sedan
The rear caliper with the parking brake built in.
Signs of wear: A dragging rear wheel or a weak parking brake.
See all Rear Brake Caliper parts for the 2004 Honda Accord Sedan
The rear pads in the rear caliper.
Signs of wear: Squealing or grinding from the rear.
See all Rear Brake Pads parts for the 2004 Honda Accord Sedan
Cars without rear discs have drum brakes: a drum over the hub with two shoes inside.
Not on every vehicle: Fitted to the DX and LX sedans and the LX coupe; EX and V6 cars have rear discs.
Signs of wear: A weak parking brake, a scraping noise, or pulsing from the rear.
Tip: Drums and shoes are not drawn; the diagram shows the rear disc brakes.
See all Rear Brake Drum parts for the 2004 Honda Accord Sedan
Rubber mounts hold the engine to the body and subframe. The passenger side mount sits on the frame rail.
Signs of wear: A thud when shifting, more vibration at idle, or an engine that rocks.
Tip: Replace a collapsed mount before it strains the others.
The transmission side mount sits on the driver frame rail; other mounts hold the front and rear of the transaxle.
Signs of wear: A clunk when shifting into gear or pulling away.
Tip: Mounts differ by transmission and engine.
See all Transmission Mount parts for the 2004 Honda Accord Sedan
The large rear bushing of the front lower arm, called the compliance bushing, is the usual one. It splits and causes a shake under braking. Upper ball joints, sway bar links and rear toe arm bushings are next.
Yes, at both ends. The front upper arm sits high above the tire on top of a tall knuckle upright, and the rear has an upper arm with a ball joint plus a short upper rear arm.
The rear toe is set by a cam bolt at the inner end of the rearmost lower arm. That bolt often seizes in its sleeve, so replacement toe arms come with a new one.
Almost all of them. The sedan is 70 mm longer between the wheels than the coupe, and a few brake pads and front links differ by trim, engine and build plant, so check the fit notes on each part.
EX and V6 cars have rear discs, which the diagram shows. DX and LX cars have rear drums and shoes, listed with the brakes.
Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.