Complete Front Strut Assemblies
A front strut with its spring, mount and boot already assembled, so no spring compressor is needed.
This interactive diagram shows the front suspension, steering, axles and rear suspension of the 2008 Chevrolet Cobalt. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit your Cobalt, down to the side and position.
We carry parts for it Not stocked yet Hover or tap any part.
The Cobalt uses MacPherson struts at the front, with the coil spring on the strut and a stamped L shaped lower control arm under each corner. The steering rack sits behind the axle on a cradle and the front sway bar runs behind the cradle with links up to the struts. The rear is a twist beam: two trailing arms joined by a perforated cross beam, with a separate coil spring on each arm and a shock behind the axle. The diagram shows the base car with 15 inch wheels, front disc brakes and rear drum brakes.
We carry replacement parts for 27 of the 37 components on this diagram, 106 parts in all. See every part for the 2008 Chevrolet Cobalt.
A front strut with its spring, mount and boot already assembled, so no spring compressor is needed.
Front and rear struts for the whole car in one order.
Tie rods and boots for both sides in one order.
Polyurethane bushings for the whole car in one order.
A pressed steel L shaped arm. The ball joint bolts to its outer end, a leg runs in to a small front bushing at the cradle, and from that corner a second leg runs back to a large upright bushing. Stamped steel on most cars, aluminum on the SS and sport suspensions.
Signs of wear: Creaking or popping in slow tight turns, clunks over bumps or under braking, or wandering on the highway.
Tip: Left and right arms are different parts. Complete arms with the ball joint fitted save pressing the joint over.
See all Front Control Arm parts for the 2008 Chevrolet Cobalt
The small horizontal bushing in the eye at the inner end of the arm's front leg, on a bolt that runs front to back through the cradle.
Signs of wear: A clunk when pulling away or braking, or torn rubber.
Tip: Polyurethane sets replace the arm's inner bushings.
See all Front Control Arm Bushings parts for the 2008 Chevrolet Cobalt
The large upright bushing at the end of the arm's rear leg, held in the arm and bolted up into the cradle.
Signs of wear: Creaks in slow turns, shimmy under braking, or rubber that has split.
Tip: This bushing wears more often than any other part of the front arm. Offset versions add caster.
See all Front Control Arm Bushings parts for the 2008 Chevrolet Cobalt
The ball joint bolts to the outer end of the lower arm. Its stud points up into the bottom of the knuckle and is held by a nut. Soft ride and sport arms take different joints.
Signs of wear: A clunk over bumps, play when the wheel is rocked top to bottom, or a torn boot.
Tip: One ball joint fits both sides. Check whether your arm is stamped steel or aluminum.
See all Front Lower Ball Joint parts for the 2008 Chevrolet Cobalt
The cast knuckle carries the wheel bearing and hub. Its top sits in the strut's two bolt clevis, the ball joint stud goes into its bottom, and the tie rod joins its steering arm behind the axle.
Signs of wear: A bent knuckle after a curb strike pulls the car to one side.
Tip: Complete knuckle assemblies come with the bearing, hub and backing plate.
The MacPherson strut clamps the top of the knuckle in a two bolt clevis and runs up to the strut tower. It carries the coil spring, and a tab on its body holds the top of the sway bar link.
Signs of wear: Bouncing after bumps, nose dive under braking, fluid on the strut body, or a knock from the top of the strut.
Tip: Left and right struts are different parts. Complete strut assemblies need no spring compressor.
The front coil spring sits on a seat on the strut body and pushes up against the top mount, with rubber insulators at its ends.
Signs of wear: A corner sitting low, a broken coil end, or a clunk when turning at low speed.
Tip: Replace springs in pairs.
See all Front Coil Springs parts for the 2008 Chevrolet Cobalt
A rubber boot over the strut rod, inside the coil spring, with the bump stop at its top. It keeps dirt off the rod seal.
Signs of wear: A torn boot, or a harsh bang when the suspension bottoms out.
Tip: Replace the boot and bump stop whenever the strut is replaced.
See all Front Shock Bellows Boot Kit parts for the 2008 Chevrolet Cobalt
The rubber mount and bearing at the top of the strut. Three studs hold it to the strut tower under the hood.
Signs of wear: Knocks or creaks from the top of the strut over bumps or while turning the wheel at a standstill.
Tip: Replace the mount with the strut; it comes fitted on complete strut assemblies.
See all Front Strut Mount parts for the 2008 Chevrolet Cobalt
The two bolts that hold the strut's clevis to the top of the knuckle. Offset cam bolts in their place let the camber be set.
Signs of wear: Uneven wear on the inside or outside edge of the front tires after a curb strike.
Tip: Check the bolt size (15 or 17 mm) in the fit notes, then align the car.
See all Front End Alignment Kit parts for the 2008 Chevrolet Cobalt
The front sway bar runs across behind the cradle. Its ends bend forward to the links that rise to the struts.
Signs of wear: A bar seldom fails; worn links and bushings are what make the noise.
Tip: Check the links and bushings first.
Two rubber bushings in clamps hold the front bar to the cradle.
Signs of wear: A squeak or a dull knock over bumps from the front of the car.
Tip: Bushings are sold for 18, 20.8, 22 and 24 mm bars. Measure the bar or check the fit notes.
See all Front Sway Bar Bushings parts for the 2008 Chevrolet Cobalt
A link with a ball stud at each end, in two lengths (about 250 and 300 mm). The top bolts to a tab on the strut body and the bottom to the end of the sway bar.
Signs of wear: A rattle or clunk over small bumps is the most common sign.
Tip: Hold the stud with a hex key while you turn the nut.
See all Front Sway Bar Endlinks parts for the 2008 Chevrolet Cobalt
The outer tie rod end threads onto the inner rod. Its stud goes up through the knuckle's steering arm behind the axle.
Signs of wear: Loose steering, a clunk when turning, or uneven tire wear.
Tip: Left and right ends are different parts. Count the turns when you unscrew the old one, then align the car.
See all Front Outer Tie Rod End parts for the 2008 Chevrolet Cobalt
The inner tie rod screws into the end of the steering rack under the boot.
Signs of wear: Play in the steering with the boot squeezed, or a clunk over bumps.
Tip: One inner rod fits both sides.
See all Front Inner Tie Rod End parts for the 2008 Chevrolet Cobalt
A rubber boot at each end of the rack keeps dirt out of the inner tie rod joint.
Signs of wear: A split boot, or grease on the rack.
Tip: Replace the boot whenever an inner tie rod is replaced.
See all Steering Rack Bellow parts for the 2008 Chevrolet Cobalt
The steering rack sits behind the front axle on the cradle, held in rubber mount bushings. Its pinion rises on the driver side to the steering column, which carries the electric assist motor.
Signs of wear: Clunks over bumps, wandering, or a leak at a boot. Worn mount bushings let the rack shift in turns.
Tip: Align the car after any rack work.
A half shaft runs from the transmission to each front hub. The passenger shaft is the long one.
Signs of wear: Clicking when turning, a vibration on acceleration, or grease thrown from a split boot.
Tip: Shafts are listed by transmission (automatic or manual) and side.
See all CV Joint Parts - Front parts for the 2008 Chevrolet Cobalt
A twist beam (torsion beam): two trailing arms joined by a cross beam ahead of the wheels. Each arm pivots on a rubber bushing in a body bracket ahead of the wheel and carries the hub, the brake, the coil spring and the shock.
Signs of wear: Clunks from the rear over bumps, or the rear wheels steering the car, point to worn pivot bushings.
Tip: The beam itself is not sold here. Camber and toe shims fit between the beam and the hub.
The rear shock bolts to a bracket on the trailing arm behind the axle and runs up into the body. The coil spring sits separately on the arm.
Signs of wear: Bouncing after bumps, the rear swaying, or fluid on the body.
Tip: The rear coil spring is a separate part on this car.
See all Rear Shock Absorber parts for the 2008 Chevrolet Cobalt
The rear coil spring sits on a seat on the trailing arm and pushes up into the body.
Signs of wear: A corner sitting low, or a broken coil end.
Tip: Replace springs in pairs.
See all Rear Coil Springs parts for the 2008 Chevrolet Cobalt
A rubber bump stop on the rear shock rod.
Signs of wear: A torn boot, or a bang when the rear bottoms out.
Tip: Replace it with the strut.
A thin tapered shim between the arm's hub plate and the rear hub. Fitting one changes the rear camber and toe.
Signs of wear: Rear tires wearing on one edge when the rear alignment is out of range.
Tip: Shims come in steps of angle. Fit one per side, then align the car.
See all Rear End Alignment Kit parts for the 2008 Chevrolet Cobalt
A separate rear bar across the beam, on the cars that have one, or added as an upgrade.
Not on every vehicle: Only on cars with the aftermarket rear bar
Signs of wear: Body roll at the rear in fast turns.
Tip: Bolt on bars clamp to the beam.
Bushings that hold an aftermarket rear bar.
Not on every vehicle: Only on cars with the aftermarket rear bar
Signs of wear: A squeak or knock from the rear.
Tip: Check that your car has a separate rear bar before ordering.
Links between a separate rear bar and the body.
Not on every vehicle: Only on cars with the aftermarket rear bar
Signs of wear: A rattle from the rear over small bumps.
Tip: Check that your car has a separate rear bar before ordering.
The front bearing is pressed into the knuckle and the hub is pressed through it.
Signs of wear: A hum or growl that changes with speed or when turning, or play in the wheel.
Tip: Pressing the bearing needs a press; a complete knuckle assembly avoids that.
A bolt on hub and bearing unit on the end of the beam, with four wheel studs on the base car (five on the SS and 16 inch wheel cars).
Signs of wear: A hum from the rear that rises with speed, or play in the wheel.
Tip: Cars with ABS take the hub with the sensor; check the fit notes.
See all Rear Wheel Bearing and Hub Assembly parts for the 2008 Chevrolet Cobalt
A 256 mm vented rotor on the 4 stud front hub (280, 296 and 315 mm rotors fit 5 stud cars).
Signs of wear: A pulsing pedal, grooves, or a lip at the edge.
Tip: Check the rotor size and stud count before ordering.
See all Front Brake Rotor parts for the 2008 Chevrolet Cobalt
A single piston floating caliper on a bracket bolted to the knuckle, ahead of the axle.
Signs of wear: Pulling to one side when braking, a dragging wheel, or a leak.
Tip: Bleed the brakes after replacing one.
The pads sit in the caliper bracket either side of the rotor.
Signs of wear: Squealing, grinding, or a long pedal.
Tip: Replace pads on both sides together.
See all Front Brake Pads parts for the 2008 Chevrolet Cobalt
A 230 mm drum over the rear hub covers the shoes.
Signs of wear: A pulsing pedal when stopping gently, or a grinding noise from the rear.
Tip: Check the shoes and wheel cylinder with the drum off.
Two shoes on the backing plate inside the drum, pushed out by the wheel cylinder. They also work the parking brake.
Signs of wear: A parking brake lever that pulls up too far, or grinding from the rear.
Tip: Shoes differ by year: Wagner Z795 for 2005-2008 (9-1/16 x 1-43/64 in. brakes). Check the fit notes.
See all Rear Brake Shoes parts for the 2008 Chevrolet Cobalt
A 270 mm rear rotor on the cars that have rear disc brakes.
Not on every vehicle: Only on cars with rear disc brakes (listed as Sport and SS in the fit data)
Signs of wear: A pulsing pedal or a grooved rotor.
Tip: Most Cobalts of these years have rear drums.
See all Rear Brake Rotor parts for the 2008 Chevrolet Cobalt
A rear caliper on the cars that have rear disc brakes.
Not on every vehicle: Only on cars with rear disc brakes (listed as Sport and SS in the fit data)
Signs of wear: A dragging rear wheel, or a leak.
Tip: Most Cobalts of these years have rear drums.
See all Rear Brake Caliper parts for the 2008 Chevrolet Cobalt
Rear pads for the cars that have rear disc brakes.
Not on every vehicle: Only on cars with rear disc brakes (listed as Sport and SS in the fit data)
Signs of wear: Squealing or grinding from the rear.
Tip: Most Cobalts of these years have rear drums.
Small shoes inside the hat of each rear rotor work the parking brake on rear disc cars.
Not on every vehicle: Only on cars with rear disc brakes (listed as Sport and SS in the fit data)
Signs of wear: A parking brake that does not hold.
Tip: Not on drum brake cars, whose drum shoes do the job.
The front lower control arm bushings (the large upright one at the rear of the arm especially), front sway bar links, outer tie rod ends, struts and strut mounts are the parts most often replaced.
No. The front uses MacPherson struts, so the strut itself locates the top of the knuckle. There is one lower control arm and one lower ball joint per side.
No. The rear is a twist beam: both wheels ride on trailing arms joined by a cross beam that twists to let each side move. There are no rear control arms to replace; the pivot bushings at the front of each arm, the coil springs, the shocks and the hubs are the wear parts.
Yes. The SS and cars with the sport suspensions use aluminum lower control arms with their own ball joints and bushings, 5 stud hubs, larger front rotors (280, 296 or 315 mm) and, on some cars, rear disc brakes. The diagram shows the base car, so check the fit notes on each part.
No. Most base, LS and LT cars have rear drums, but cars with rear disc brakes use rotors and pads at the back. Look at the rear wheel or check the fit notes before ordering rear brake parts.
Many suspension parts are shared across these cars. The fit notes on each part list the vehicles it fits, so check them before ordering.
Yes, after replacing tie rods, struts, control arms or the rear shims. Front toe is set at the tie rods and front camber can be corrected with a cam bolt in the strut clevis. Rear camber and toe are adjusted with shims between the arm and the hub.
Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.