Front End Steering Rebuild Kits
Package kits bundle the wearing front end parts in one order, usually for less than buying them one by one.
This interactive diagram shows the front suspension, steering, driveline and rear suspension of the 2004 GMC Envoy 4x4. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit, down to the side and position.
We carry parts for it Not stocked yet Hover or tap any part.
The 2002 to 2009 Envoy and Chevrolet Trailblazer 4WD share this layout: upper and lower control arms with a coilover strut standing on each lower arm, rack and pinion steering behind the front wheels, and a front differential bolted to the side of the engine oil pan with CV shafts out to the wheels. The rear is a solid axle on coil springs, located by two lower arms, two upper arms and a track bar, with a sway bar ahead of the axle and a one piece driveshaft.
We carry replacement parts for 40 of the 51 components on this diagram, 118 parts in all. See every part for the 2004 GMC Envoy 4WD.
Package kits bundle the wearing front end parts in one order, usually for less than buying them one by one.
Front and rear shock sets for the whole vehicle.
One kit with the suspension bushings for the whole vehicle.
Front and rear lowering kits for the street.
The upper ball joint sits in the tip of the U shaped upper control arm. Its stud points down into the top of the knuckle.
Signs of wear: Clunks over bumps, wandering steering, or play when the wheel is rocked top to bottom.
Tip: The joint presses into the arm, so it can be replaced on its own. The same joint fits every year from 2002 to 2009.
See all Front Upper Ball Joint parts for the 2004 GMC Envoy 4WD
The lower ball joint presses into the tip of the lower control arm and is held by a snap ring. Its stud points up into the bottom of the knuckle.
Signs of wear: Clunks over bumps, a loose front end, or play when the wheel is rocked top to bottom with the vehicle on a jack.
Tip: It carries the weight of the vehicle, so it usually wears first. A lower arm with the joint already fitted saves pressing it in.
See all Front Lower Ball Joint parts for the 2004 GMC Envoy 4WD
A U shaped steel arm that holds the top of the knuckle. The coilover passes up through the middle of the U, and its two bushings pivot on a bracket on top of the frame rail.
Signs of wear: Clunks, torn bushings, or a worn ball joint.
Tip: The same arm fits every 2002 to 2009 Trailblazer and Envoy, including the long wheelbase models.
A stamped steel A arm under each corner. Its two bushings pivot on the engine crossmember and a bracket under the frame, and the coilover stands on its rear leg.
Signs of wear: Clunks over bumps, torn bushings, or a worn lower ball joint.
Tip: The arm changed for 2004 and again for 2008 (the sway bar link stud size changed), so order by year.
A cast bracket bolted under the frame rail that carries the rear pivot of the lower control arm.
Signs of wear: A cracked bracket or a clunk from the rear of the lower arm. The 2002 models were recalled to replace this bracket.
Tip: Check the bolts and the bracket for cracks whenever the lower arm is off.
Rubber bushings in the two eyes of the upper control arm.
Signs of wear: Clunks, steering that shifts under braking, or cracked rubber at the eyes.
Tip: Polyurethane kits press into the original arm.
See all Front Control Arm Bushings parts for the 2004 GMC Envoy 4WD
Rubber bushings in the front and rear eyes of the lower control arm.
Signs of wear: Clunks over bumps or on braking, or cracked rubber at the eyes.
Tip: The forward and rearward bushings are different sizes.
See all Front Control Arm Bushings parts for the 2004 GMC Envoy 4WD
The bushing in the bottom eye of the strut, where it bolts to the rear leg of the lower control arm.
Signs of wear: A knock from the front over small bumps.
Tip: It comes with a new strut assembly, and is sold on its own for the original strut.
See all Front Control Arm Bushings parts for the 2004 GMC Envoy 4WD
The knuckle joins the two ball joints, carries the hub and caliper, and has the steering arm at the back for the outer tie rod.
Signs of wear: A bent knuckle after a curb strike, or worn ball joint bores.
Tip: Swap the hub and caliper bracket over to the new knuckle.
The front shock and coil spring are one coilover unit. Its bottom eye bolts to the lower arm, and it passes up through the upper arm to a tower on the frame with three studs.
Signs of wear: Bouncing after bumps, nose dive under braking, oil on the body, or a clunk from the top mount.
Tip: A complete strut assembly with the spring and mount saves using a spring compressor.
See all Front Shock Absorber parts for the 2004 GMC Envoy 4WD
The coil spring around the front strut carries the front of the vehicle.
Signs of wear: A sagging front, uneven height side to side, or a broken coil.
Tip: The Trailblazer and the Envoy 4WD use different spring rates. Replace in pairs.
Rubber pads at the ends of the front coil spring that stop it rattling against its seats.
Signs of wear: A squeak or creak when turning or over bumps.
Tip: Replace them whenever the spring is off the strut.
See all Front Coil Spring Isolator Pads parts for the 2004 GMC Envoy 4WD
The top plate of the strut, with three studs up through the frame tower.
Signs of wear: A clunk from the top of the strut over bumps.
Tip: Included with a complete strut assembly.
A rubber bumper on the strut rod inside the top of the spring.
Signs of wear: A harsh bang over big bumps.
Tip: It comes with a complete strut assembly.
A steel bar across the front of the vehicle, ahead of the crossmember, linking the two lower arms to reduce body roll.
Signs of wear: Body roll, or a clunk if a bushing or link is worn.
Tip: Bar size changed over the years, so measure it before ordering bushings.
Two bushings clamp the front sway bar under the front of the frame rails.
Signs of wear: Clunks or squeaks over bumps.
Tip: Bar sizes differ by year: 2004 to 2009 most use 34.5 mm, some 2006 to 2009 36.5 mm. Measure the bar.
See all Front Sway Bar Bushings parts for the 2004 GMC Envoy 4WD
A short link with a ball stud at each end, from the end of the sway bar down to the lower control arm.
Signs of wear: A clunk or rattle over small bumps.
Tip: The link changed in 2004 and 2008, so order by year.
See all Front Sway Bar Endlinks parts for the 2004 GMC Envoy 4WD
Shims and tools for setting caster and camber at the upper control arm.
Signs of wear: An alignment that cannot reach spec.
Tip: A tool that moves the upper arm makes adjustment easier.
The long outer tie rod end runs back from the inner tie rod to the steering arm at the rear of the knuckle.
Signs of wear: Loose steering, wander, or uneven tire wear.
Tip: Count the threads when you take it off, then get an alignment.
See all Front Outer Tie Rod End parts for the 2004 GMC Envoy 4WD
The inner tie rod screws into the end of the rack inside the boot.
Signs of wear: Clunks when turning, or play you can feel through the boot.
Tip: Replace the boot clamps with it.
See all Front Inner Tie Rod End parts for the 2004 GMC Envoy 4WD
A rubber bellows at each end of the rack keeps dirt away from the inner tie rod.
Signs of wear: A split boot, or fluid in the boot.
Tip: A torn boot ruins the inner tie rod, so replace it as soon as you see it.
See all Steering Rack Bellow parts for the 2004 GMC Envoy 4WD
The vehicle steers with a hydraulic rack and pinion behind the front wheels, bolted to the engine crossmember.
Signs of wear: Fluid leaks, a heavy spot in the steering, or knocks from the rack.
Tip: We list the boots and tie rods.
Each front wheel is driven by a CV shaft. The driver one bolts to the differential, the passenger one to the axle disconnect on the other side of the engine oil pan.
Signs of wear: Clicking on turns, a torn boot, or grease on the inside of the wheel.
Tip: The same shaft fits both sides.
See all CV Joint Parts - Front parts for the 2004 GMC Envoy 4WD
The U-joint where the front driveshaft meets the front differential.
Signs of wear: A clunk when the four wheel drive engages, or a squeak at low speed.
Tip: Replace the straps with the joint.
The U-joint at the rear of the front driveshaft, behind the transfer case output.
Signs of wear: A clunk in four wheel drive.
Tip: Check both ends of the shaft together.
The U-joint at the front of the one piece rear driveshaft, behind the transfer case.
Signs of wear: A clunk on take off, or a vibration that grows with speed.
Tip: The same 1-1/8 inch cap joint is used at both ends of the rear shaft.
The U-joint at the rear axle pinion.
Signs of wear: A clunk on take off or a squeak at low speed.
Tip: Straps hold this joint to the pinion yoke. Replace them with the joint.
A tubular link under each side, from below the axle bracket forward to a bracket under the frame rail.
Signs of wear: A clunk on take off or braking.
Tip: Tighten the bolts with the weight on the wheels.
A shorter link above each lower arm, from the ear on top of the axle bracket forward to the frame.
Signs of wear: A clunk from the rear, or a vibration on take off.
Tip: Vehicles with rear air leveling use an upper arm with a sensor tab. Check yours.
One bar behind the axle, from a bracket on the driver side of the axle to a bracket on the passenger frame rail. It keeps the axle centered.
Signs of wear: The rear moves side to side over bumps, or a clunk when changing lanes.
Tip: We list the bushings for the original bar.
Bushings in both eyes of the rear track bar.
Signs of wear: Clunks when turning or changing lanes.
Tip: Replace both ends together.
See all Rear Track Arm Bar Bushings parts for the 2004 GMC Envoy 4WD
Bushings in both eyes of each rear control arm.
Signs of wear: Clunks over bumps or on take off.
Tip: Kits for this rear cover all four arms.
See all Rear Control Arm Bushings parts for the 2004 GMC Envoy 4WD
A coil spring on each side, between a seat on the axle bracket and a pocket under the frame rail.
Signs of wear: A sagging rear, uneven height, or a broken coil.
Tip: Vehicles with rear air springs use a conversion kit to change to coils.
A rubber insulator between the top of the rear spring and the frame.
Signs of wear: A creak or squeak from the rear over bumps.
Tip: Replace them with the springs.
See all Rear Coil Spring Isolator Pads parts for the 2004 GMC Envoy 4WD
Some vehicles have rear air springs with automatic leveling in place of the coil springs. They sit where the coils are drawn.
Not on every vehicle: Vehicles with rear automatic leveling (air springs) only; coil springs are drawn.
Signs of wear: A rear that sags overnight, or a compressor that runs often.
Tip: A conversion kit replaces the air springs with coils and shocks.
A bar across the vehicle ahead of the rear axle, clamped to the axle with two bushings, its ends linked up to the frame.
Signs of wear: Body roll, or a clunk from a worn bushing.
Tip: A thicker bar reduces body roll when towing.
Two bushings clamp the rear sway bar to brackets on the axle.
Signs of wear: Clunks or squeaks over bumps.
Tip: Measure the bar before ordering.
See all Rear Sway Bar Bushings parts for the 2004 GMC Envoy 4WD
A link with a ball stud at each end, from the sway bar end up to a bracket on the frame.
Signs of wear: A rattle or clunk from the rear.
Tip: The studs have an Allen socket to hold them while the nut is turned.
See all Rear Sway Bar Endlinks parts for the 2004 GMC Envoy 4WD
A shock on each side, outboard of the spring, from the axle bracket up to the frame.
Signs of wear: Bouncing, a floaty rear, or oil on the shock body.
Tip: Replace in pairs.
See all Rear Shock Absorber parts for the 2004 GMC Envoy 4WD
A rubber bumper under the frame above the axle.
Signs of wear: A harsh bang when the rear bottoms out.
Tip: Check them when you replace the springs.
A bearing pressed into each end of the rear axle housing, inside the tube, that carries the axle shaft.
Signs of wear: A hum from the rear that changes with speed.
Tip: Replace the seal with it.
See all Rear Wheel Bearing Assembly parts for the 2004 GMC Envoy 4WD
A sealed hub and bearing bolted to the knuckle with three bolts. The CV shaft splines through it.
Signs of wear: A hum that changes with speed, or ABS warning lights.
Tip: Coated versions resist rust on the flange.
See all Front Wheel Bearing and Hub Assembly parts for the 2004 GMC Envoy 4WD
The vented front rotor sits on the hub flange under the wheel.
Signs of wear: Pulsing in the pedal or scoring.
Tip: Two sizes are listed for 2002 to 2005 (305 and 325 mm), and the 2006 to 2009 rotor is 302 mm. Measure yours.
The floating front caliper sits at the rear of the rotor.
Signs of wear: Pulling under braking, a sticking brake, or fluid leaks.
Tip: The caliper changed for 2006.
See all Front Brake Caliper parts for the 2004 GMC Envoy 4WD
The pads sit in the caliper either side of the rotor.
Signs of wear: Squeal, grinding, or a long pedal.
Tip: The pad changed for 2006, so order by year.
The vented rear rotor, with the parking brake drum inside its hat.
Signs of wear: Pulsing in the pedal, or a weak parking brake.
Tip: Replace in pairs.
The single piston rear caliper sits behind the axle.
Signs of wear: A dragging rear brake or a leak.
Tip: Same caliper 2002 to 2009.
The rear pads in the caliper either side of the rotor.
Signs of wear: Squeal or grinding from the rear.
Tip: Same pad 2002 to 2009.
A small shoe inside the hat of each rear rotor, used only for the parking brake.
Signs of wear: A parking brake that will not hold.
Tip: Adjust them through the rotor before fitting the caliper.
See all Parking Brake Shoes parts for the 2004 GMC Envoy 4WD
Rubber mounts between the engine and the frame.
Signs of wear: A clunk on take off or extra vibration at idle.
Tip: Check both sides together.
Rubber cushions between the frame and the body, on outriggers along both rails.
Signs of wear: A clunk or shift from the body over bumps.
Tip: Replace them as a set.
Lower ball joints, outer tie rod ends and sway bar links wear first. Check them with the front wheels off the ground: a worn joint shows up as play you can feel when you rock the wheel.
Coil springs at both ends. The front spring sits on the strut as one coilover unit, and the rear springs sit between the axle and the frame. There are no torsion bars.
Two lower control arms and two upper control arms keep the axle square, and a track bar behind the axle keeps it centered under the body. Worn bushings in any of them cause clunks and a loose feel at the rear.
Mostly. The arms, ball joints, tie rods, hubs and rear links are shared, but the front coil springs differ in rate between the Trailblazer and the Envoy 4WD. Vehicles with rear air leveling use air springs and their own upper arms.
The 2002 to 2009 Trailblazer and Envoy 4WD use this layout. Some parts changed along the way: the front lower arm and sway bar links for 2004 and 2008, and the front brakes for 2006. The parts shown here are the ones listed for the 2004 4WD Envoy.
Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.