Front End Steering Rebuild Kits
Package kits bundle the wearing front end parts in one order, usually for less than buying them one by one.
This interactive diagram shows the front suspension, steering and rear suspension of the 2007 Saturn Aura. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit your Aura, down to the side and position.
We carry parts for it Not stocked yet Hover or tap any part.
The Aura uses MacPherson struts at the front, with the coil spring on the strut and an L shaped lower control arm under each corner on a perimeter cradle. The steering rack sits behind the front axle and the front sway bar links run up to the struts. The rear is a multi-link design on an X shaped crossmember: a curved upper arm, a wide lower arm that carries the coil spring and a short lateral link hold each rear knuckle, a flat trailing arm runs forward from the knuckle to a bushing in the body, and a separate shock absorber damps each corner. The diagram shows the model with four wheel disc brakes.
We carry replacement parts for 32 of the 40 components on this diagram, 81 parts in all. See every part for the 2007 Saturn Aura.
Package kits bundle the wearing front end parts in one order, usually for less than buying them one by one.
A strut with its spring, mount and boot already assembled, so no spring compressor is needed.
The strut is the front shock absorber and the upper locating part of the corner in one. A two bolt clevis at its bottom clamps the top of the knuckle, the coil spring sits on it, and its top mount bolts into the strut tower.
Signs of wear: Bouncing after bumps, nose dive under braking, fluid on the tube, or a knock from the top of the strut over rough roads.
Tip: The same struts fit the 2004 to 2012 Malibu, the 2005 to 2010 G6 and the 2007 to 2009 Aura. Complete assemblies come with the spring and mount fitted.
The front coil spring sits on the strut between a seat on the strut tube and the top mount, with rubber insulators at each end.
Signs of wear: A corner that sits low, a clunk over bumps from a broken coil end, or tires rubbing on full lock.
Tip: Two spring rates are listed (Moog 81230 and 81232), and the hardtop convertible has its own. Compress the spring with a proper tool before taking the strut apart.
The top mount holds the strut in the strut tower with three studs and has a bearing so the strut can turn with the steering.
Signs of wear: A clunk or creak at the top of the strut when turning the wheel, or a strut top that moves in the tower.
Tip: Left and right mounts are different parts on some brands. The mount is usually replaced with the strut.
A rubber boot covers the strut rod, with the bump stop inside it under the top mount.
Signs of wear: A torn boot lets grit onto the rod and wears the strut seal; a missing bump stop gives a harsh bang on big bumps.
Tip: Fit a new boot and bump stop whenever the strut is replaced.
See all Front Shock Bellows Boot Kit parts for the 2007 Saturn Aura
A cam bolt in the upper hole of the strut clevis lets the shop set front camber.
Not on every vehicle: An aftermarket part. The factory strut bolts are plain.
Signs of wear: Uneven tire wear on the inner or outer edge after the car hit a curb or pothole.
Tip: The factory clevis bolt is plain; a cam bolt adds about 1.75 degrees of camber adjustment.
See all Front End Alignment Kit parts for the 2007 Saturn Aura
An L shaped stamped arm under each front corner. Its front leg ends in a bushing on a bolt that runs front to back, its rear leg ends in a large bushing held in a bracket under the cradle, and the ball joint is pressed into its outer end.
Signs of wear: Clunks over bumps or when braking, steering that wanders, or uneven inner tire wear.
Tip: Left and right arms are different parts. The arm comes with both bushings and the ball joint fitted, and the same arm fits every 2004 to 2012 Malibu, G6 and Aura.
Each lower arm has two bushings: a small one in the front leg on a bolt that runs front to back, and a large one at the end of the rear leg in a clamp bracket bolted under the cradle.
Signs of wear: Clunks when braking or pulling away, a vague steering feel, or a shimmy at speed.
Tip: Front (forward) and rear (rearward) bushings are different parts.
See all Front Control Arm Bushings parts for the 2007 Saturn Aura
The lower ball joint is pressed into the outer end of the lower arm. Its stud goes up into the bottom of the knuckle and is held by a pinch bolt.
Signs of wear: A clunk over bumps, play when the wheel is rocked top to bottom, or a torn boot.
Tip: Replacement arms come with the joint fitted. Separate joints are listed for 2004 and 2005 Malibus.
The knuckle carries the hub bearing and the caliper. The strut clevis clamps its top, the ball joint stud fits its bottom and the outer tie rod bolts to its steering arm behind the axle.
Signs of wear: The knuckle rarely wears out; it is replaced after accident damage or a seized bearing.
The front sway bar runs across the car on two rubber bushings on the cradle, with each end joined to its strut by a long link.
Signs of wear: Body roll in turns, or a clunk if the bar or its bushings are loose.
Tip: Most cars have a 22 mm bar; 2004 to 2008 Malibu sedans and early G6s also used a 19 mm bar. Check the bar size before ordering bushings.
Two rubber bushings in clamps hold the front bar to the cradle.
Signs of wear: Squeaks or clunks over bumps and in turns.
Tip: Bushings fit one bar diameter only (19 mm or 22 mm).
See all Front Sway Bar Bushings parts for the 2007 Saturn Aura
A long link with a ball stud at each end, from the end of the sway bar up to a bracket on the strut tube.
Signs of wear: A knock from the front over small bumps, worst at low speed.
Tip: Links changed in 2010: 2004 to 2009 cars use a 300 mm link (Moog K80252) and 2010 to 2012 cars a slightly longer one (Moog K750519). The same link fits both sides.
See all Front Sway Bar Endlinks parts for the 2007 Saturn Aura
The rack and pinion sits on the rear of the front cradle, behind the axle. Power assist comes from an electric motor on the steering column, so the rack has no fluid lines.
Signs of wear: Play in the steering, a clunk through the wheel, or a torn boot.
Tip: Replace a torn boot quickly, before grit reaches the rack.
The inner tie rod screws into the end of the rack inside the boot and carries the outer end on its thread.
Signs of wear: Play in the steering or a clunk when turning.
Tip: The same inner rod fits both sides.
See all Front Inner Tie Rod End parts for the 2007 Saturn Aura
The outer tie rod end threads onto the inner rod; its ball stud fits the knuckle steering arm behind the axle.
Signs of wear: Steering play, wandering, or feathered tire wear.
Tip: Count the turns when unscrewing the old end and get an alignment after fitting the new one.
See all Front Outer Tie Rod End parts for the 2007 Saturn Aura
A shaft with a constant velocity joint at each end drives each front wheel from the transaxle.
Signs of wear: Clicking in tight turns, grease thrown around the wheel from a torn boot, or a vibration when accelerating.
Tip: Axles differ by engine and transaxle (Moog 10S019, and 10E024L and 10E024R on many 2008 to 2012 cars).
See all CV Joint Parts - Front parts for the 2007 Saturn Aura
The rear knuckle carries the hub and the caliper. The upper arm bolts to its top, the two lower arms to its bottom, and the trailing arm bolts to its front.
Signs of wear: The knuckle rarely wears out, but the bushing pressed into it for the lower rear arm does.
A bushing pressed into the bottom of the rear knuckle, where the outer end of the lower rear arm bolts on.
Signs of wear: A clunk from the rear or rear tires that wear on the inner edge.
See all Rear Control Arm Bushings parts for the 2007 Saturn Aura
A flat stamped arm bolted to the front of the rear knuckle, running forward to a large bushing on a bracket under the body. It holds the wheel fore and aft.
Signs of wear: A clunk on braking or over bumps, or a car that steps sideways on rough roads.
Tip: Left and right arms differ, and cars with rear drum brakes use their own arms.
The large bushing in the front end of the trailing arm, bolted through a bracket under the body.
Signs of wear: A clunk on braking, or a car that steps sideways over bumps.
See all Trailing Arm Bushings parts for the 2007 Saturn Aura
The wide stamped lower arm behind the axle, from the rear of the crossmember out to a fork at the bottom of the knuckle. The rear coil spring sits in a seat on it.
Signs of wear: A clunk from the rear, uneven rear tire wear, or a spring that sits crooked.
Tip: One arm fits both sides.
The bushing at the inner end of the lower rear arm, on the crossmember.
Signs of wear: A clunk from the rear, or a rear tire that wears on its inner edge.
See all Rear Control Arm Bushings parts for the 2007 Saturn Aura
A short straight link with a bushing in each end, ahead of the lower rear arm, from the crossmember to the bottom front of the knuckle. It sets the rear toe.
Signs of wear: Rear tires that wear on the edges, or a loose feel at the rear in turns.
Tip: Adjustable toe parts are sold to correct the rear toe.
A curved stamped arm from the crossmember up to the top of the rear knuckle. It sets the rear camber.
Signs of wear: Rear tires that wear on the inner edge, or a clunk from the rear.
Tip: One arm fits both sides.
The rear shock stands behind the spring. Its lower eye bolts to the rear knuckle and its stem goes up through the body.
Signs of wear: Bouncing or floating over bumps, fluid on the body, or a knock from the rear.
Tip: Fit new mount parts with new shocks.
The rear coil spring sits between a seat on the lower rear arm and a seat under the body, on its own, beside the shock.
Signs of wear: A rear corner that sits low, or a clunk from a broken coil end.
Tip: Rear springs differ by trim and body: sedan, coupe and the hardtop convertible take different sets.
Rubber bushings, washers and a bracket that hold the rear shock stem in the body.
Signs of wear: A knock or rattle from the rear over bumps.
Tip: Fit new mount parts whenever the shock is replaced.
The rear sway bar runs across behind the crossmember on two rubber bushings, with each end joined to the lower rear arm by a short link.
Signs of wear: Body roll in turns, or a clunk if the bar or bushings are loose.
Tip: Rear bars are 18, 19 or 20 mm by trim. Check the size before ordering bushings.
Two rubber bushings in clamps hold the rear bar.
Signs of wear: Squeaks or clunks from the rear.
Tip: Bushings fit one bar diameter only.
See all Rear Sway Bar Bushings parts for the 2007 Saturn Aura
A short flat link with a rubber bushing in each end, from the end of the rear bar down to a bracket on the lower rear arm.
Signs of wear: A knock from the rear over small bumps.
Tip: The same link fits both sides and every year.
See all Rear Sway Bar Endlinks parts for the 2007 Saturn Aura
Listed here, not drawn: rear cam bolts, toe adjusters and shims that let a shop set rear camber and toe.
Not on every vehicle: An aftermarket correction part. The diagram shows the factory plain bolts.
Signs of wear: Uneven tire wear, or an alignment that is out of range after a lift, leveling kit or a hard hit.
Tip: The factory rear bolts are plain; these kits add about plus or minus 2 degrees of camber or toe.
See all Rear End Alignment Kit parts for the 2007 Saturn Aura
A sealed bearing and hub unit bolted to the knuckle from behind with three bolts. The CV axle splines through its center.
Signs of wear: A hum or growl that changes in turns, play in the wheel, or an ABS light.
Tip: Hubs differ with and without anti-lock brakes; coated and plain versions fit the same cars.
See all Front Wheel Bearing and Hub Assembly parts for the 2007 Saturn Aura
A vented rotor clamped between the hub and the wheel.
Signs of wear: Pulsing in the pedal, scoring, or a lip at the edge.
Tip: Two front rotor sizes are listed: 296 mm on most cars and 276 mm on some 2004 to 2008 Malibus and 2005 to 2007 G6s. Measure the old rotor before ordering.
A single piston sliding caliper on a bracket bolted to the knuckle.
Signs of wear: Pulling to one side, a sticking brake that runs hot, or fluid at the piston seal.
Tip: Calipers differ by rotor size (276 mm or 296 mm).
Two pads in the caliper, one either side of the rotor.
Signs of wear: Squealing, a grinding noise, or a long pedal.
Tip: Pads changed during the run: 2004 to 2006 Malibus and 2005 G6s take one pad set (Wagner 1028), later cars another (Wagner 1160).
A sealed bearing and hub unit bolted to the rear knuckle with four bolts.
Signs of wear: A hum or growl from the rear, or an ABS light.
Tip: Hubs differ with and without anti-lock brakes.
See all Rear Wheel Bearing and Hub Assembly parts for the 2007 Saturn Aura
A 270 mm solid rotor on the rear hub.
Signs of wear: Pulsing, scoring or rust ridges.
A single piston caliper on a bracket on the rear knuckle, with the parking brake built in.
Signs of wear: A dragging rear brake or a parking brake that will not hold.
Two pads in each rear caliper.
Signs of wear: Squealing or grinding from the rear.
Tip: The piston screws back in, because of the built in parking brake.
Listed here, not drawn: the diagram shows the rear disc brakes.
Not on every vehicle: Fitted to some base models (2004 to 2007 Malibu, 2006 to 2008 G6); most cars have rear discs.
Signs of wear: A low or soft pedal, or a parking brake that will not hold.
Tip: Drum brake cars use their own rear trailing arms.
Front sway bar links, front lower control arms and their rear bushings, outer tie rod ends, front strut mounts and the rear trailing arm bushings are the parts most often replaced, followed by struts and rear shocks.
Most do. The Aura shares its lower arms, ball joints, struts, tie rods, hubs, rear arms, trailing arms and rear shocks with the 2005 to 2010 G6 and the 2008 to 2012 Malibu. Springs, sway bar bushings and some brake parts differ by trim and year, so check the fit of each part before ordering.
No. The front uses struts, so the strut itself locates the top of the knuckle. There is one lower control arm per side with the ball joint pressed into it. The rear has an upper arm on each side.
Yes, after replacing tie rods, struts, control arms or rear arms. Front toe is set at the tie rods, front camber can be corrected with a cam bolt in the strut clevis, and rear camber and toe kits are sold for the rear arms.
Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.