2012 Toyota Corolla Suspension Diagram

This interactive diagram shows the front suspension, steering, axles and rear suspension of the 2012 Toyota Corolla with the 1.8 liter engine, as built in North America. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit your car, down to the side.

2012 Toyota Corolla Suspension Diagram (Full Car)

FRONT
Both ends of the car from above the driver side. The front of the car is to the left.

2012 Toyota Corolla Front Suspension and Steering Diagram

PASSENGER SIDEDRIVER SIDEFRONT
Front strut suspension and steering from above the front of the car.

2012 Toyota Corolla Rear Suspension Diagram

DRIVER SIDEPASSENGER SIDEREAR
Rear torsion beam suspension from above the rear driver side corner.

We carry parts for it Not stocked yet Hover or tap any part.

Kits and packages for your 2012 Toyota Corolla

2 kits

Packages

Front End Steering Rebuild Package Kit
Includes
  • 2 × Outer Tie Rod End
  • 2 × Inner Tie Rod End
  • 2 × Front Lower Ball Joint
  • Front Lower Control Arm (optional)
$459.56
View package
Complete Shock Package Kit
Includes
  • 2 × Front Strut (driver and passenger)
  • 2 × Rear Shock
$520.12
View package

See every part for the 2012 Toyota Corolla

The 2009 to 2013 Corolla uses MacPherson struts up front, each clamping the knuckle in a two bolt clevis above an L shaped lower control arm with a bolted on ball joint. Links rise from the sway bar to the struts, and the steering rack sits behind the front axle. The rear is a torsion beam: two trailing arms joined by a cross beam, with a coil over shock on the back of each arm and drum brakes on the 1.8 liter car.

We carry replacement parts for 27 of the 34 components on this diagram, 100 parts in all. See every part for the 2012 Toyota Corolla.

Questions about the 2012 Toyota Corolla suspension

What wears out most often on a 2012 Corolla suspension?

The front lower control arm bushings, especially the large upright rear bushing, sway bar links, struts and strut mounts. Creaking or popping in slow tight turns is usually the arm bushings.

Does it matter where my Corolla was built?

Yes. This diagram is for cars built in North America, whose VIN starts with 1, 2 or 5. Cars built in Japan (VIN starts with J) take their own front lower control arms, inner and outer tie rods, rack boots and strut mounts. Check the fit notes on each part against your VIN.

Does the 2012 Corolla have a rear sway bar?

No separate rear bar is listed for this car. The rear is a torsion beam: the cross beam that joins the two trailing arms twists as the car leans, which does the job of a bar.

Do I need an alignment after replacing these parts?

Yes, after tie rods, control arms, struts or the camber bolts. The rear has no adjusters; camber and toe shims fit between the beam and each rear hub.

Which years share this suspension?

The 2009 to 2013 Corolla uses this layout, and nearly every part we list carries over from one year to the next. The 2.4 liter cars of 2009 and 2010 add rear disc brakes and their own front struts and half shafts.

Printable 2012 Toyota Corolla suspension diagrams

Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.

2012 Toyota Corolla  Suspension Diagram (Full Car) with numbered parts
2012 Toyota Corolla Suspension Diagram (Full Car)
2012 Toyota Corolla  Front Suspension and Steering Diagram with numbered parts
2012 Toyota Corolla Front Suspension and Steering Diagram
2012 Toyota Corolla  Rear Suspension Diagram with numbered parts
2012 Toyota Corolla Rear Suspension Diagram