This interactive diagram shows the front suspension, steering linkage, driveline and rear suspension of the 2002 Ford F-150 4x4. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit, down to the side and position.
The 2002 F-150 4x4 holds its front on forged upper and lower control arms with a torsion bar on each side, running back from the lower arm to an adjustable key in a crossmember behind the transmission. CV axles run out from a frame mounted front differential, and a center link ahead of the axle, held by the pitman arm and idler arm, steers both wheels through tie rods with adjusting sleeves. The rear is a solid axle on leaf springs, clamped on top of the axle tubes with U-bolts and hung from a shackle at the rear of each spring, with drum brakes.
Packages and kits
Package kits bundle the wearing steering parts for this truck in one order.
Front and rear shock sets for the whole truck.

Position: Front and RearQty per vehicle: 1
$319.80
View part

Position: Front and RearQty per vehicle: 1
$260.00
View part

Position: Front and RearQty per vehicle: 1
$319.80
View part
One kit with the suspension bushings for the whole truck.
All the U-joints for the driveline in one order. One package fits the regular cab short box, the other every other cab and box.
Front Suspension
The upper ball joint is the top pivot between the upper control arm and the steering knuckle. Its stud points down into the knuckle.
Signs of wear: Clunks over bumps, wandering, uneven tire wear, or play when the wheel is rocked top to bottom.
Tip: On these trucks the factory joint comes in the upper arm, so most owners replace the arm and joint together.
See all Front Upper Ball Joint parts for the 2002 Ford F-150 4WD
The lower ball joint is pressed into the outer end of the lower control arm, with its stud pointing up into the knuckle. It carries the weight the torsion bar puts on the arm.
Signs of wear: Clunks, a loose front end, or play when the wheel is rocked top to bottom with the truck on a jack.
Tip: Unload the torsion bar or support the lower arm before separating the joint, then get an alignment.

Top sellerPosition: Front LowerFits: Includes Powdered-Metal Gusher Bearing To Allow Grease To Penetrate Bearing Surfaces, New Pre-Installed Integral Dust Boot Allows For Ease Of Installation, Both New and Original Designs can be Installed on VehicleQty per vehicle: 2
$56.71
View part

Position: Front LowerFits: Oversized, New Pre-Installed Integral Dust Boot Allows For Ease Of Installation, Both New and Original Designs can be Installed on VehicleQty per vehicle: 2
$58.40
View part

Position: Front LowerQty per vehicle: 2
$38.31
View part

Position: Front LowerFits: OE ReplacementQty per vehicle: 2
$45.37
View part
See all Front Lower Ball Joint parts for the 2002 Ford F-150 4WD
A forged arm shaped like an A that holds the top of the knuckle. Two bushings pivot on cam bolts at the frame, and the ball joint is at the outer end.
Signs of wear: Torn bushings, a worn ball joint, clunks, or an alignment that will not stay set.
Tip: An arm with the ball joint and bushings already fitted saves pressing them.

Top sellerPassenger sidePosition: Front Passenger Side UpperFits: Premium OE ReplacementQty per vehicle: 1
$83.43
View part

Driver sidePosition: Front Driver Side UpperFits: Premium OE ReplacementQty per vehicle: 1
$83.43
View part

Driver sidePosition: Front Driver Side UpperFits: Includes Bushing(s), High Utilization Design, with Integral Ball JointQty per vehicle: 1
$162.64
View part

Passenger sidePosition: Front Passenger Side UpperFits: Includes Bushing(s), High Utilization Design, with Integral Ball JointQty per vehicle: 1
$162.64
View part

Passenger sidePosition: Front Passenger Side UpperFits: Includes Bushing(s), High Utilization Design, Replaceable Ball JointQty per vehicle: 1
$100.53
View part

Driver sidePosition: Front Driver Side UpperQty per vehicle: 1
$82.83
View part

Passenger sidePosition: Front Passenger Side UpperQty per vehicle: 1
$82.83
View part

Driver sidePosition: Front Left Upper
$179.07
View part

Passenger sidePosition: Front Right Upper
$247.90
View part
See all Front Control Arm parts for the 2002 Ford F-150 4WD
The wide lower arm pivots on two bushings in the front crossmember. The torsion bar's front end sits in its rear pivot, and the ball joint, shock and sway bar link mount near its outer end.
Signs of wear: Clunks, worn bushings, a worn ball joint, or a tire that wears on one edge.
Tip: Unload the torsion bar with the key adjuster before removing the arm.

Top sellerPassenger sidePosition: Front Passenger Side LowerQty per vehicle: 1
$308.72
View part

Driver sidePosition: Front Driver Side LowerQty per vehicle: 1
$308.72
View part
See all Front Control Arm parts for the 2002 Ford F-150 4WD
Rubber or polyurethane bushings pressed into the two inner eyes of the upper arm, around the cam bolts.
Signs of wear: Clunks over bumps, a shifting alignment, or cracked rubber at the arm's inner end.
Tip: The cam bolts that pass through these bushings set caster and camber, so mark them before taking them out.

Position: FrontQty per vehicle: 1
$171.46
View part

Position: FrontQty per vehicle: 2
$43.44
View part

Position: Front UpperFits: Kit Contains FRONT AND REAR BUSHINGQty per vehicle: 2
$45.04
View part
See all Front Control Arm Bushings parts for the 2002 Ford F-150 4WD
Bushings in the lower arm's front and rear eyes, where the arm pivots on the crossmember.
Signs of wear: Clunks, a pull under braking, or cracked rubber at the pivots.
Tip: The rear bushing sits around the torsion bar socket, so the bar has to be unloaded first.

Top sellerPosition: Front LowerFits: Kit Contains FRONT AND REAR BUSHINGQty per vehicle: 2
$59.73
View part

Position: FrontQty per vehicle: 1
$171.46
View part

Position: FrontQty per vehicle: 2
$43.44
View part

Position: Front Lower Rearward
$36.97
View part
See all Front Control Arm Bushings parts for the 2002 Ford F-150 4WD
Cam bolts and washers through the upper arm's inner bushings. Turning them moves the arm in or out to set caster and camber.
Signs of wear: Rusted, seized or worn cams, or a truck that cannot be aligned after a lift or new arms.
Tip: Adjustable kits give more range than the factory cams after a leveling kit.

Top sellerPosition: FrontFits: Non-Greasable, with Bolts & Cams, Plus or Minus 2-1/2 Degree(s) Camber and/or CasterQty per vehicle: 2
$50.76
View part

Position: FrontFits: Greasable, with Bolts & Cams, Plus or Minus 2-1/2 Degree(s) Camber and/or CasterQty per vehicle: 2
$85.22
View part

Position: Front Upper Control ArmQty per vehicle: 1
$62.33
View part
See all Front End Alignment Kit parts for the 2002 Ford F-150 4WD
8 Steering Knuckle (driver and passenger side)
The knuckle carries the hub and brake caliper, turns on the two ball joints, and has the steering arm the outer tie rod end bolts to.
Signs of wear: Rarely fails, but check the ball joint tapers and the caliper mounts when replacing joints.
Tip: The front axle shaft passes through the knuckle into the hub.
We don't carry a steering knuckle for the 2002 Ford F-150 4WD yet.
Ask us about this part and we will try to source it.
The front shock runs from a loop on the lower control arm up to a stem mount on the frame.
Signs of wear: Bouncing after bumps, nose dive under braking, leaks, or cupped tires.
Tip: Replace front shocks in pairs.

Position: FrontQty per vehicle: 2
$51.98
View part

Position: FrontQty per vehicle: 2
$41.54
View part

Position: FrontQty per vehicle: 2
$73.74
View part

Position: FrontQty per vehicle: 2
$81.24
View part

Position: FrontQty per vehicle: 1
$65.00
View part

Position: FrontQty per vehicle: 1
$65.00
View part

Position: FrontQty per vehicle: 1
$79.95
View part
See all Front Shock Absorber parts for the 2002 Ford F-150 4WD
10 Torsion Bar (driver and passenger side)
The front spring on the 4WD truck: a long steel bar from the lower arm's rear pivot back to a key in a crossmember behind the transmission. Twisting it holds the front up.
Signs of wear: A front end that sits low on one side or both.
Tip: Ride height is set at the key adjuster bolt, not by changing the bar.
We don't carry a torsion bar for the 2002 Ford F-150 4WD yet.
Ask us about this part and we will try to source it.
11 Torsion Bar Key (driver and passenger side)
The key is the lever on the rear end of each torsion bar. An adjuster bolt under it sets how much the bar is twisted, which sets the front height.
Signs of wear: A front end that cannot be raised to height, or a seized adjuster bolt.
Tip: Leveling keys index the bar further to lift the front. Unload the bar with a puller before removing a key.

Fits: Forged Universal Torsion Bar Loading and Unloading Tool Kit - Safely Loads and Unloads Torsion Bar Suspensions for Key ReplacementQty per vehicle: 1
$415.67
View part

Position: FrontFits: Adjustable -1/2 to 1-1/2 Degrees, Allows Front Ride Height Changes Up To 2 Above OEMQty per vehicle: 1
$412.22
View part
See all Torsion Bar Key Lift Kit parts for the 2002 Ford F-150 4WD
12 Front Sway Bar
A steel bar across the front, bushed to the frame, with its ends linked down to the lower control arms. It reduces body roll.
Signs of wear: A cracked bar is rare; look for broken links and worn bushings first.
Tip: A thicker bar firms up roll. The factory bar size varies by option, so check the bushing size.
We don't carry a front sway bar for the 2002 Ford F-150 4WD yet.
Ask us about this part and we will try to source it.
Rubber bushings that hold the sway bar to the frame in clamp brackets.
Signs of wear: Squeaks or clunks over bumps, or a bar that moves in its brackets.
Tip: Measure the bar first: these trucks came with 27, 30, 33 and 35 mm bars.

Top sellerPosition: FrontQty per vehicle: 1
$51.06
View part

Position: Front To FrameFits: 30 Sway Bar DiameterQty per vehicle: 1
$36.16
View part

Position: FrontQty per vehicle: 1
$50.76
View part

Position: Front To FrameFits: 27 Sway Bar DiameterQty per vehicle: 1
$27.89
View part

Position: Front To FrameFits: 35 Sway Bar DiameterQty per vehicle: 1
$35.44
View part

Position: Front To FrameFits: 33 Sway Bar DiameterQty per vehicle: 1
$36.16
View part

Position: Front To FrameFits: 0.354 Width, 2.559 Bore Diameter, 2.564 Outside Diameter Seal, 1.889 Shaft Diameter
$36.88
View part

Position: FrontQty per vehicle: 1
$62.99
View part
See all Front Sway Bar Bushings parts for the 2002 Ford F-150 4WD
A long bolt with a spacer sleeve and rubber bushings that joins each end of the sway bar to the lower control arm.
Signs of wear: Rattles over bumps, torn bushings, or a broken bolt.
Tip: Replace both sides together.

Top sellerPosition: FrontFits: Includes Polyurethane Bushings and Solid Metal Sleeve for Enhanced Performance - Barrel Nut Allows for Easier InstallationQty per vehicle: 2
$16.76
View part

Position: FrontQty per vehicle: 2
$13.41
View part
See all Front Sway Bar Endlinks parts for the 2002 Ford F-150 4WD
Steering
The center link runs across the front ahead of the axle. The pitman arm and idler arm hold it, and the inner tie rod ends bolt into its ends.
Signs of wear: Play in the steering, wander, or worn tapered holes.
Tip: This link is the 4WD part. The 2WD truck uses another one.
See all Tie Rod Center Link parts for the 2002 Ford F-150 4WD
The pitman arm is splined to the steering gear's output shaft and moves the center link when the wheel is turned.
Signs of wear: Play at its ball stud, or a loose arm on the gear shaft.
Tip: Use a puller to remove the arm from the splines.

Top sellerFits: Includes Greasable Socket Design to Reduce Corrosion and WearQty per vehicle: 1
$75.16
View part
See all Pitman Arm parts for the 2002 Ford F-150 4WD
The idler arm holds the passenger end of the center link to the frame and pivots as the link moves.
Signs of wear: Up and down play at the passenger end of the link, wander, or uneven tire wear.
Tip: Two bracket hole spacings were used, 2.48 in and 3.43 in. Measure yours before ordering.

Top sellerFits: with 2-1/2 Between Mount Holes, Includes Powdered-Metal Gusher Bearing To Allow Grease To Penetrate Bearing SurfacesQty per vehicle: 1
$156.13
View part

Fits: with 3-1/2 Between Mount Holes, Includes Powdered-Metal Gusher Bearing To Allow Grease To Penetrate Bearing SurfacesQty per vehicle: 1
$246.36
View part
See all Idler Arm parts for the 2002 Ford F-150 4WD
The inner tie rod end is a ball joint whose stud bolts into the end of the center link. Its threaded shank goes into the adjusting sleeve.
Signs of wear: Play in the steering, torn boots, or toe that keeps changing.
Tip: Count the turns when removing it from the sleeve, then get an alignment.

Top sellerPassenger sidePosition: Front Passenger Side InnerFits: Includes Powdered-Metal Gusher Bearing To Allow Grease To Penetrate Bearing SurfacesQty per vehicle: 1
$62.22
View part

Driver sidePosition: Front Driver Side InnerFits: Includes Powdered-Metal Gusher Bearing To Allow Grease To Penetrate Bearing SurfacesQty per vehicle: 1
$62.22
View part

Driver sidePosition: Front Left InnerFits: Includes Powdered-Metal Gusher Bearing To Allow Grease To Penetrate Bearing Surfaces
$49.78
View part

Passenger sidePosition: Front Passenger Side InnerFits: Includes Powdered-Metal Gusher Bearing To Allow Grease To Penetrate Bearing SurfacesQty per vehicle: 1
$49.78
View part

Driver sidePosition: Front Left Inner
$45.75
View part

Passenger sidePosition: Front Right Inner
$105.50
View part
See all Front Inner Tie Rod End parts for the 2002 Ford F-150 4WD
A threaded steel tube with two clamps that joins the inner and outer tie rod ends. Turning it sets the toe.
Signs of wear: A sleeve rusted to the tie rod ends, or bent from an impact.
Tip: Replace a seized sleeve with the tie rod ends, and set the toe afterward.

Position: FrontQty per vehicle: 2
$24.89
View part
See all Tie Rod Adjusting Sleeve parts for the 2002 Ford F-150 4WD
The outer tie rod end is a ball joint whose stud goes down through the steering arm of the knuckle.
Signs of wear: Play, a torn boot, clunks, or a feathered tire edge.
Tip: Replace in pairs and align afterward.

Top sellerPassenger sidePosition: Front Passenger Side OuterFits: Includes Powdered-Metal Gusher Bearing To Allow Grease To Penetrate Bearing SurfacesQty per vehicle: 1
$59.96
View part

Driver sidePosition: Front Driver Side OuterFits: Includes Powdered-Metal Gusher Bearing To Allow Grease To Penetrate Bearing SurfacesQty per vehicle: 1
$59.96
View part

Driver sidePosition: Front Left Outer
$46.42
View part

Driver sidePosition: Front Driver Side OuterFits: Includes Powdered-Metal Gusher Bearing To Allow Grease To Penetrate Bearing SurfacesQty per vehicle: 1
$47.97
View part

Passenger sidePosition: Front Passenger Side OuterFits: Includes Powdered-Metal Gusher Bearing To Allow Grease To Penetrate Bearing SurfacesQty per vehicle: 1
$47.97
View part

Passenger sidePosition: Front Right Outer
$136.60
View part
See all Front Outer Tie Rod End parts for the 2002 Ford F-150 4WD
21 Steering Gear Box
The power steering gear bolts to the driver side frame rail ahead of the front axle. Its output shaft turns the pitman arm.
Signs of wear: Leaks, a dead spot in the wheel, or play at the gear's output shaft.
Tip: Check the linkage before the gear: worn joints feel the same.
We don't carry a steering gear box for the 2002 Ford F-150 4WD yet.
Ask us about this part and we will try to source it.
Driveline
22 Front CV Axle (driver and passenger side)
The front axle shaft runs from the frame mounted front differential to the hub, with a CV joint in a boot at each end.
Signs of wear: Clicking in turns, grease thrown from a torn boot, or vibration.
Tip: Replace a torn boot quickly; dirt wears out the joint.
See all CV Joint Parts - Front parts for the 2002 Ford F-150 4WD
The U-joint where the front driveshaft meets the front differential.
Signs of wear: Clunks when shifting into gear, squeaks, or vibration in 4WD.
Tip: Check the size listed for your suspension option before ordering.

Position: At Center Bearing, At Rear Axle, At Transmission, Front Driveshaft at Front Axle, Front Driveshaft at Transfer Case, Rear Driveshaft at Rear Axle, Rear Driveshaft at TransmissionFits: 1.063 Bearing Caps, Greasable Super Strength U-Joint, with 1-1/16 Outside Diameter Bearing(s)
$30.18
View part

Position: At Center Bearing, At Rear Axle, At Transmission, Front Driveshaft at Front Axle, Front Driveshaft at Transfer Case, Rear Driveshaft at Rear Axle, Rear Driveshaft at TransmissionFits: 1.063 Bearing Caps, Non-Greasable Super Strength U-Joint, with 1-1/16 Outside Diameter Bearing(s)
$27.69
View part

Position: Front Driveshaft at Front AxleFits: Only Fits Lube Fitting in Bearing Cup, PremiumQty per vehicle: 1
$31.51
View part

Position: Front Driveshaft at Front AxleFits: Only Fits Lube Fitting in Body, PremiumQty per vehicle: 1
$22.09
View part
See all U Joint parts for the 2002 Ford F-150 4WD
The U-joint where the front driveshaft leaves the transfer case.
Signs of wear: Clunks, squeaks, or vibration in 4WD.
Tip: Grease it when servicing the truck.

Position: At Center Bearing, At Rear Axle, At Transmission, Front Driveshaft at Front Axle, Front Driveshaft at Transfer Case, Rear Driveshaft at Rear Axle, Rear Driveshaft at TransmissionFits: 1.063 Bearing Caps, Greasable Super Strength U-Joint, with 1-1/16 Outside Diameter Bearing(s)
$30.18
View part

Position: At Center Bearing, At Rear Axle, At Transmission, Front Driveshaft at Front Axle, Front Driveshaft at Transfer Case, Rear Driveshaft at Rear Axle, Rear Driveshaft at TransmissionFits: 1.063 Bearing Caps, Non-Greasable Super Strength U-Joint, with 1-1/16 Outside Diameter Bearing(s)
$27.69
View part

Position: Front Driveshaft at Transfer CaseFits: Only Fits Lube Fitting in Bearing Cup, PremiumQty per vehicle: 1
$31.51
View part

Position: Front Driveshaft at Transfer CaseFits: Only Fits Lube Fitting in Body, PremiumQty per vehicle: 1
$22.09
View part
See all U Joint parts for the 2002 Ford F-150 4WD
The U-joint at the front of the rear driveshaft, behind the transfer case.
Signs of wear: A clunk taking off, squeaks, or vibration at speed.
Tip: Mark the shaft before removal so it goes back in phase.

Position: At Center Bearing, At Rear Axle, At Transmission, Front Driveshaft at Front Axle, Front Driveshaft at Transfer Case, Rear Driveshaft at Rear Axle, Rear Driveshaft at TransmissionFits: 1.063 Bearing Caps, Greasable Super Strength U-Joint, with 1-1/16 Outside Diameter Bearing(s)
$30.18
View part

Position: At TransmissionQty per vehicle: 1
$31.51
View part

Position: At Center Bearing, At Rear Axle, At Transmission, Front Driveshaft at Front Axle, Front Driveshaft at Transfer Case, Rear Driveshaft at Rear Axle, Rear Driveshaft at TransmissionFits: 1.063 Bearing Caps, Non-Greasable Super Strength U-Joint, with 1-1/16 Outside Diameter Bearing(s)
$27.69
View part

Position: Rear Driveshaft at TransmissionFits: Only Fits Lube Fitting in Bearing Cup, PremiumQty per vehicle: 1
$31.51
View part

Position: At TransmissionQty per vehicle: 1
$22.09
View part

Position: Rear Driveshaft at TransmissionFits: 0.059 Ring Thickness, 1.188 Bearing Caps, Only Fits Steel DriveshaftQty per vehicle: 1
$71.24
View part

Position: Rear Driveshaft at TransmissionFits: Only Fits Lube Fitting in Body, PremiumQty per vehicle: 1
$22.09
View part

Position: Rear Driveshaft at TransmissionFits: 0.059 Ring Thickness, 1.188 Bearing Caps, Only Fits Steel Driveshaft, Premium, Spicer 1350 SeriesQty per vehicle: 1
$25.42
View part

Position: Rear Driveshaft at TransmissionFits: 0.059 Ring Thickness, 1.188 Bearing Caps, Only Fits Steel DriveshaftQty per vehicle: 1
$28.87
View part
See all U Joint parts for the 2002 Ford F-150 4WD
The U-joint at the rear axle's pinion yoke.
Signs of wear: A clunk taking off, squeaks, or vibration at speed.
Tip: Replace both rear joints together.

Position: At Center Bearing, At Rear Axle, At Transmission, Front Driveshaft at Front Axle, Front Driveshaft at Transfer Case, Rear Driveshaft at Rear Axle, Rear Driveshaft at TransmissionFits: 1.063 Bearing Caps, Greasable Super Strength U-Joint, with 1-1/16 Outside Diameter Bearing(s)
$30.18
View part

Position: At Center Bearing, At Rear Axle, At Transmission, Front Driveshaft at Front Axle, Front Driveshaft at Transfer Case, Rear Driveshaft at Rear Axle, Rear Driveshaft at TransmissionFits: 1.063 Bearing Caps, Non-Greasable Super Strength U-Joint, with 1-1/16 Outside Diameter Bearing(s)
$27.69
View part

Position: Rear Driveshaft at Rear AxleFits: Only Fits Lube Fitting in Bearing Cup, PremiumQty per vehicle: 1
$31.51
View part

Position: At Rear AxleFits: Only Fits Lube Fitting in Bearing Cup, PremiumQty per vehicle: 1
$31.51
View part

Position: Rear Driveshaft at Rear AxleFits: 0.059 Ring Thickness, 1.188 Bearing Caps, Only Fits Steel DriveshaftQty per vehicle: 1
$71.24
View part

Position: Rear Driveshaft at Rear AxleFits: Only Fits Lube Fitting in Body, PremiumQty per vehicle: 1
$22.09
View part

Position: At Rear AxleFits: Only Fits Lube Fitting in Body, PremiumQty per vehicle: 1
$22.09
View part

Position: Rear Driveshaft at Rear AxleFits: 0.059 Ring Thickness, 1.188 Bearing Caps, Only Fits Steel Driveshaft, Premium, Spicer 1350 SeriesQty per vehicle: 1
$25.42
View part

Position: Rear Driveshaft at Rear AxleFits: 0.059 Ring Thickness, 1.188 Bearing Caps, Only Fits Steel DriveshaftQty per vehicle: 1
$28.87
View part
See all U Joint parts for the 2002 Ford F-150 4WD
The U-joint at the center support bearing on trucks with a two piece rear driveshaft.
Not on every vehicle: Only trucks with a two piece rear driveshaft (some SuperCab and SuperCrew trucks). The SuperCab with the 6.5 ft box drawn here has a one piece shaft.
Signs of wear: Vibration at speed or a clunk taking off.
Tip: Only trucks with a two piece rear driveshaft have this joint.

Position: At Center BearingFits: Only Fits Lube Fitting in Bearing Cup, PremiumQty per vehicle: 1
$31.51
View part

Position: Rear Driveshaft at Support BearingFits: 0.059 Ring Thickness, 1.188 Bearing Caps, Only Fits 2 Piece Rear Driveshaft, Only Fits Steel Driveshaft, Premium, Spicer 1350 SeriesQty per vehicle: 1
$25.42
View part

Position: Rear Driveshaft at Support BearingFits: 0.059 Ring Thickness, 1.188 Bearing Caps, Only Fits 2 Piece Rear Driveshaft, Only Fits Steel DriveshaftQty per vehicle: 1
$71.24
View part

Position: At Center BearingFits: Only Fits Lube Fitting in Body, PremiumQty per vehicle: 1
$22.09
View part

Position: Rear Driveshaft at Support BearingFits: 0.059 Ring Thickness, 1.188 Bearing Caps, Only Fits 2 Piece Rear Driveshaft, Only Fits Steel DriveshaftQty per vehicle: 1
$28.87
View part
See all U Joint parts for the 2002 Ford F-150 4WD
Rear Suspension
34 Rear Leaf Spring (driver and passenger side)
A pack of steel leaves on each side that carries the rear of the truck. It sits on top of the axle tube, held by two U-bolts, with an eye at each end.
Signs of wear: A rear end that sags, a broken leaf, or a spring that has shifted on the axle.
Tip: Replace springs in pairs.
We don't carry a rear leaf spring for the 2002 Ford F-150 4WD yet.
Ask us about this part and we will try to source it.
The bushing pressed into the spring's front eye, where the spring pivots on the front hanger.
Signs of wear: Clunks taking off and stopping, or a rear axle that steers the truck over bumps.
Tip: Polyurethane kits replace the front and rear eye bushings together.

Position: Rear ForwardQty per vehicle: 2
$36.80
View part
See all Rear Leaf Spring Bushings parts for the 2002 Ford F-150 4WD
The bushing in the spring's rear eye, where the spring hangs from the shackle.
Signs of wear: Squeaks or clunks over bumps.
Tip: Replace with the shackle bushings.
See all Rear Leaf Spring Bushings parts for the 2002 Ford F-150 4WD
Two plates that hang the spring's rear eye from a bracket on the frame, so the spring can lengthen as it flexes.
Signs of wear: Clunks, a rusted or bent shackle, or worn bushings.
Tip: The listed shackle is for trucks under 7700 GVW.

Position: Rear RearwardFits: Under 7,700 Gross Vehicle Weight (GVW)Qty per vehicle: 2
$80.47
View part
See all Rear Leaf Spring Shackles parts for the 2002 Ford F-150 4WD
The bushing in the frame bracket where the shackle pivots.
Signs of wear: Squeaks or clunks over bumps.
Tip: Replace with the shackle.

Position: Rear RearwardQty per vehicle: 2
$36.82
View part
See all Rear Leaf Spring Shackle Bushings parts for the 2002 Ford F-150 4WD
39 Rear Axle U-Bolts (driver and passenger side)
Two U-bolts on each side wrap under the axle tube and clamp the spring to the top of it with a plate on the spring.
Signs of wear: Loose U-bolts let the axle shift on the springs.
Tip: Use new U-bolts and nuts whenever they are removed.
We don't carry a rear axle u-bolts for the 2002 Ford F-150 4WD yet.
Ask us about this part and we will try to source it.
The rear shock runs from a bracket under the axle tube up and back to the frame, inboard of the spring.
Signs of wear: Bouncing, a floaty rear, leaks, or cupped tires.
Tip: Trucks with the 7700 GVW package use their own rear shocks.

Position: RearFits: Doesn't Fit 7,700 Gross Vehicle Weight (GVW)Qty per vehicle: 2
$40.57
View part

Position: RearFits: Only Fits 7,700 Gross Vehicle Weight (GVW)Qty per vehicle: 2
$75.19
View part

Position: RearFits: Doesn't Fit 7,700 Gross Vehicle Weight (GVW)Qty per vehicle: 2
$75.22
View part

Position: RearFits: Only Fits 7,700 Gross Vehicle Weight (GVW)Qty per vehicle: 2
$80.56
View part

Position: RearFits: Doesn't Fit 7,700 Gross Vehicle Weight (GVW)Qty per vehicle: 2
$71.70
View part

Position: RearFits: Doesn't Fit 7,700 Gross Vehicle Weight (GVW)Qty per vehicle: 2
$79.72
View part

Position: RearFits: Doesn't Fit 7,700 Gross Vehicle Weight (GVW)Qty per vehicle: 1
$234.41
View part

Position: RearFits: Lowering Nitro Drop 2 SeriesQty per vehicle: 1
$65.00
View part

Position: RearFits: Lowering Street Performance SeriesQty per vehicle: 1
$79.95
View part

Position: RearQty per vehicle: 1
$79.95
View part
See all Rear Shock Absorber parts for the 2002 Ford F-150 4WD
47 Rear Sway Bar Not on every vehicle
A bar across the rear axle with its ends linked up to the frame.
Not on every vehicle: Some trucks only. The 2001 truck in our lift photos has no rear bar, so it is not drawn.
Signs of wear: Rattles from broken links or worn bushings.
Tip: Not every truck has a rear bar.
We don't carry a rear sway bar for the 2002 Ford F-150 4WD yet.
Ask us about this part and we will try to source it.
Bushings that hold the rear sway bar in its clamps.
Not on every vehicle: Trucks with a rear sway bar only.
Signs of wear: Squeaks or clunks over bumps.
Tip: Match the bar diameter.
See all Rear Sway Bar Bushings parts for the 2002 Ford F-150 4WD
49 Rear Sway Bar Links (driver and passenger side) Not on every vehicle
Links from the ends of the rear sway bar up to the frame.
Not on every vehicle: Trucks with a rear sway bar only (listed for 1997-2001 XL, XLT and Lariat 4WD).
Signs of wear: Rattles over bumps.
Tip: Replace both sides.
See all Rear Sway Bar Endlinks parts for the 2002 Ford F-150 4WD
Brakes and Hubs
A sealed hub and bearing unit bolted to the knuckle. The front axle shaft's splines drive it, and the rotor and wheel bolt to its studs.
Signs of wear: Humming or growling that changes in turns, play at the wheel, or an ABS light.
Tip: Trucks with the 7700 GVW package use a 7 stud hub; the 5 stud hub is drawn.

Position: FrontFits: with 5 Stud Hub, Not CoatedQty per vehicle: 2
$312.96
View part

Position: FrontFits: Only Fits 7 Stud HubQty per vehicle: 2
$423.22
View part
See all Front Wheel Bearing and Hub Assembly parts for the 2002 Ford F-150 4WD
The vented front disc that bolts to the hub under the wheel.
Signs of wear: Pulsing in the pedal, grooves, or a lip at the edge.
Tip: Replace in pairs with new pads.
No imagePosition: FrontFits: Only Fits 7,700 Gross Vehicle Weight (GVW)Qty per vehicle: 2
$57.52
View part

Position: FrontFits: 5 Stud Wheel, Doesn't Fit 7,700 GVW, Only Fits 307 Front RotorQty per vehicle: 2
$68.14
View part

Position: FrontFits: 5 Stud Wheel, Doesn't Fit 7,700 GVW, Only Fits 307 Front RotorQty per vehicle: 2
$83.14
View part

Position: FrontFits: 5 Stud Wheel, Doesn't Fit 7,700 GVW, Only Fits 307 Front RotorQty per vehicle: 2
$84.78
View part

Position: FrontFits: Only Fits 7,700 Gross Vehicle Weight (GVW)Qty per vehicle: 2
$114.82
View part
See all Front Brake Rotor parts for the 2002 Ford F-150 4WD
The caliper straddles the rotor behind the axle and squeezes the pads against it.
Signs of wear: A pull to one side, a sticking brake, or a leak.
Tip: The calipers listed for this section are the 7700 GVW package ones; check your truck's package before ordering. Bleed the brakes afterward.

Passenger sidePosition: Front Passenger SideQty per vehicle: 1
$95.96
View part

Driver sidePosition: Front Driver SideQty per vehicle: 1
$95.96
View part

Passenger sidePosition: Front Passenger SideQty per vehicle: 1
$98.90
View part

Driver sidePosition: Front Driver SideQty per vehicle: 1
$98.90
View part
See all Front Brake Caliper parts for the 2002 Ford F-150 4WD
The pads sit in the caliper either side of the rotor.
Signs of wear: Squealing, grinding, or a long pedal.
Tip: Ceramic pads make less dust.

Position: FrontFits: Under 7700 Gross Vehicle Weight (GVW)Qty per vehicle: 1
$40.14
View part

Position: FrontFits: Doesn't Fit 7700 GVWQty per vehicle: 1
$44.90
View part

Position: FrontFits: Doesn't Fit 7700 GVWQty per vehicle: 1
$51.38
View part

Position: FrontFits: Only Fits Mechanical Pad Sensors, Under 7700 Gross Vehicle Weight (GVW)Qty per vehicle: 1
$57.12
View part

Position: FrontFits: Doesn't Fit 7700 GVWQty per vehicle: 1
$59.92
View part

Position: FrontFits: Under 7700 Gross Vehicle Weight (GVW)Qty per vehicle: 1
$65.02
View part

Position: FrontFits: Under 7700 Gross Vehicle Weight (GVW)Qty per vehicle: 1
$66.60
View part

Position: FrontFits: Doesn't Fit 7700 GVWQty per vehicle: 1
$94.56
View part
See all Front Brake Pads parts for the 2002 Ford F-150 4WD
41 Rear Brake Drum (driver and passenger side)
The cast iron drum on each end of the rear axle. The wheel bolts over it and the shoes inside press out against it.
Signs of wear: Pulsing when braking, scoring, or a drum worn past its limit.
Tip: Check the shoes and hardware whenever a drum is off.
We don't carry a rear brake drum for the 2002 Ford F-150 4WD yet.
Ask us about this part and we will try to source it.
Two curved shoes inside each rear drum, pushed out against it by the wheel cylinder. On these trucks they also work as the parking brake.
Signs of wear: Grinding, a low pedal, or a parking brake that will not hold.
Tip: Adjust the shoes after fitting the drum.

Position: RearFits: Only Fits 11-1/32 x 2-1/4 BrakesQty per vehicle: 1
$57.10
View part
See all Rear Brake Shoes parts for the 2002 Ford F-150 4WD
43 Rear Brake Rotor (driver and passenger side) Not on every vehicle
The rear disc on trucks with rear disc brakes.
Not on every vehicle: Rear disc brakes. The 2001 F-150 4WD XL, XLT and Lariat drawn here have rear drums.
Signs of wear: Pulsing, grooves, or a weak parking brake.
Tip: Check the parking shoes when the rotor is off.

Position: RearFits: 5 Stud Wheel, Doesn't Fit 7,700 GVW, Only Fits 334 Diameter Rear Brake RotorQty per vehicle: 2
$66.66
View part

Position: RearFits: 5 Stud Wheel, Doesn't Fit 7,700 GVW, Only Fits 334 Diameter Rear Brake RotorQty per vehicle: 2
$85.94
View part

Position: RearFits: 5 Stud Wheel, Doesn't Fit 7,700 GVW, Only Fits 334 Diameter Rear Brake RotorQty per vehicle: 2
$88.52
View part
See all Rear Brake Rotor parts for the 2002 Ford F-150 4WD
44 Rear Brake Caliper (driver and passenger side) Not on every vehicle
The rear caliper on trucks with rear disc brakes.
Not on every vehicle: Rear disc brakes only; the drawn truck has rear drums.
Signs of wear: A dragging brake or a leak.
Tip: Bleed the brakes afterward.

Passenger sidePosition: Rear Passenger SideQty per vehicle: 1
$55.28
View part

Driver sidePosition: Rear Driver SideQty per vehicle: 1
$55.28
View part
See all Rear Brake Caliper parts for the 2002 Ford F-150 4WD
45 Rear Brake Pads (driver and passenger side) Not on every vehicle
The pads in the rear calipers on trucks with rear disc brakes.
Not on every vehicle: Rear disc brakes only; the drawn truck has rear drums.
Signs of wear: Squealing or grinding from the rear.
Tip: Replace both sides together.

Position: RearFits: Includes Pad Installation Hardware, Optional Ceramic Disc PadsQty per vehicle: 1
$44.16
View part

Position: RearFits: Only Fits Mechanical Pad SensorsQty per vehicle: 1
$44.72
View part

Position: RearFits: OE Pad Material is Semi-Metallic, Optional Semi-Metallic Disc PadsQty per vehicle: 1
$52.16
View part

Position: RearFits: Includes Pad Installation Hardware, Optional Ceramic Disc PadsQty per vehicle: 1
$57.14
View part

Position: RearFits: Includes Pad Installation HardwareQty per vehicle: 1
$82.46
View part
See all Rear Brake Pads parts for the 2002 Ford F-150 4WD
46 Parking Brake Shoes (driver and passenger side) Not on every vehicle
Small shoes inside the rear rotor's hat on trucks with rear disc brakes.
Not on every vehicle: Rear disc brakes only; on the drum brake truck drawn here the rear shoes are the parking brake.
Signs of wear: A parking brake that will not hold.
Tip: Adjust them before fitting the rotor.

Position: RearQty per vehicle: 1
$45.56
View part
See all Parking Brake Shoes parts for the 2002 Ford F-150 4WD
Body and Mounts
Rubber cushions between the cab and the frame brackets. The kits differ by cab: regular cab, SuperCab and SuperCrew.
Signs of wear: Clunks, a cab that shifts on the frame, or cracked rubber.
Tip: Replace the whole set at once and match the kit to your cab.
See all Body Mount Bushings parts for the 2002 Ford F-150 4WD
The rubber mount between the transmission and its crossmember.
Signs of wear: Clunks shifting into gear or a vibration at idle.
Tip: Support the transmission before unbolting it.
See all Transmission Mount parts for the 2002 Ford F-150 4WD