2004 GMC Yukon 2WD Suspension Diagram

This interactive diagram shows the front suspension, steering linkage, driveline and rear suspension of the 2004 GMC Yukon 2WD. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit, down to the side and position.

2004 GMC Yukon 2WD Suspension Diagram (Full Chassis)

FRONT
The whole chassis from above the driver side. The front of the vehicle is to the left. One driveshaft runs from the transmission to the rear axle.

2004 GMC Yukon 2WD Front Suspension and Steering Diagram

PASSENGER SIDEDRIVER SIDEFRONT
Front suspension and steering from above the front driver side corner. The two wheel drive truck has no front differential or CV axles. The torsion bars are shown shortened here. Their full length is on the Overview.

2004 GMC Yukon 2WD Rear Suspension Diagram

DRIVER SIDEPASSENGER SIDEREAR
Rear axle from above the rear driver side corner. The rear of the vehicle is toward the lower right.

We carry parts for it Not stocked yet Hover or tap any part.

The 2001 to 2006 Tahoe and Yukon 2WD use forged upper and lower control arms with torsion bars that run back from the lower arms to keys in a crossmember, and one straight center link between the pitman arm and the idler arm. There is no front differential: the front hubs bolt to the knuckles, and one driveshaft runs from the transmission to the rear axle. The rear is a solid axle on coil springs, located by two lower control arms, two upper control arms and a track bar, with a sway bar bushed to the axle.

We carry replacement parts for 44 of the 46 components on this diagram, 200 parts in all. See every part for the 2004 GMC Yukon 2WD.

Questions about the 2004 GMC Yukon 2WD suspension

What are the most common front end wear items on a 2004 Yukon 2WD?

The idler arm is the best known one. Ball joints, tie rod ends and the center link follow it. Check them with the wheels off the ground, because a worn idler or tie rod end shows up as play you can feel by hand.

Does the 2004 Yukon 2WD have torsion bars?

Yes. Like the 4WD, the two wheel drive Yukon uses torsion bars at the front, adjusted by a bolt under each torsion bar key, and coil springs at the rear axle.

Is the two wheel drive front hub the same as the four wheel drive hub?

No. The two wheel drive hub has no axle spline and no axle nut. It still bolts to the knuckle with three bolts and carries six wheel studs, but it is a different part, so order the 2WD hub.

What holds the rear axle in place?

Two lower control arms and two upper control arms keep the axle square, and a track bar across the back of the axle keeps it centered under the body. Worn bushings in any of them cause clunks and a loose feel at the rear.

Which years share this suspension?

The 2001 to 2006 Tahoe and Yukon 2WD share this layout. The rear brake calipers and pads changed after 2001, and some 2002 vehicles have either type, but the layout is the same. Vehicles with Autoride or rear self leveling use their own shocks. Parts can still change with options, so the parts shown here are the ones listed for the 2004 2WD Yukon.

Printable 2004 GMC Yukon 2WD suspension diagrams

Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.

2004 GMC Yukon 2WD Suspension Diagram (Full Chassis) with numbered parts
2004 GMC Yukon 2WD Suspension Diagram (Full Chassis)
2004 GMC Yukon 2WD Front Suspension and Steering Diagram with numbered parts
2004 GMC Yukon 2WD Front Suspension and Steering Diagram
2004 GMC Yukon 2WD Rear Suspension Diagram with numbered parts
2004 GMC Yukon 2WD Rear Suspension Diagram