1990 Ford F-150 4WD Suspension Diagram

This interactive diagram shows the front suspension, steering linkage, driveline and rear suspension of the 1990 Ford F-150 4WD. Hover over or tap any part to see what it does, the signs that it is worn, and the replacement parts we carry that fit your truck, down to the side and position.

1990 Ford F-150 4WD Suspension Diagram (Full Chassis)

FRONT
The whole chassis from above the driver side, drawn as a regular cab long bed. The front of the truck is to the left.

1990 Ford F-150 4WD Front Suspension and Steering Diagram

PASSENGER SIDEDRIVER SIDEFRONT
The Twin Traction Beam front, radius arms and steering linkage from above the front driver side corner.

1990 Ford F-150 4WD Rear Suspension Diagram

DRIVER SIDEPASSENGER SIDEREAR
Rear axle from above the rear driver side corner. The rear of the truck is toward the lower left.

We carry parts for it Not stocked yet Hover or tap any part.

The 1987 to 1993 F-150 4WD uses Ford's Twin Traction Beam front: a Dana 44 axle split into two beams that cross under the engine, each pivoting on the far side of the frame. The driver beam carries the front differential, coil springs sit over the radius arms, and the knuckles turn on upper and lower ball joints with a camber sleeve at the top. The front brakes are a rotor held behind the hub flange by the wheel studs, with a single piston caliper held on the knuckle by two slider pins. The steering is a drag link from the pitman arm to the passenger knuckle with the driver tie rod plugged into it. The rear is a Ford 8.8 axle on 3 inch leaf springs with drum brakes.

We carry replacement parts for 37 of the 53 components on this diagram, 208 parts in all. See every part for the 1990 Ford F-150 4WD.

Questions about the 1990 Ford F-150 4WD suspension

Why does my F-150 4WD wear the front tires on the edges?

Twin Traction Beam camber changes as the beams move, so worn axle pivot bushings, radius arm bushings or ball joints show up as edge wear. Check those parts first, then set camber with the sleeve at the upper ball joint.

Which front brake parts fit my 1990 F-150 4WD?

The 1987 to 1993 4WD trucks use a rotor held behind the hub flange by the pressed-in wheel studs, so the hub and its wheel bearings come off the spindle with it, and a single piston caliper that slides on the knuckle and is held by two slider pins. The 1994 to 1996 trucks use a different rotor, a caliper on guide pin bolts and other pads, so order by year.

Does the ball joint job need the knuckle off?

Yes. On the Dana 44 Twin Traction Beam the ball joints are pressed into the knuckle, so the hub and rotor, spindle and knuckle come off first. Replace the upper and lower joints on a side together.

Which radius arm bushings do I need?

Your 1990 truck uses the earlier radius arm bushing set (Ford changed the driver side front insulator on January 13, 1992), so order the set listed for your year.

Which years share this suspension?

The 1987 to 1993 F-150 4WD shares the axle beams, ball joints, radius arms, steering linkage, front brakes and rear spring hardware. Front sway bar bushing kits are listed by bar size (7/8 inch or 1 inch), so measure the bar before ordering. The parts shown here are the ones listed for the 1990 4WD truck.

Printable 1990 Ford F-150 4WD suspension diagrams

Numbered diagrams to print or save for the shop. The numbers match the numbered parts on the interactive diagram.

1990 Ford F-150 4WD Suspension Diagram (Full Chassis) with numbered parts
1990 Ford F-150 4WD Suspension Diagram (Full Chassis)
1990 Ford F-150 4WD Front Suspension and Steering Diagram with numbered parts
1990 Ford F-150 4WD Front Suspension and Steering Diagram
1990 Ford F-150 4WD Rear Suspension Diagram with numbered parts
1990 Ford F-150 4WD Rear Suspension Diagram